Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Alliance Laundry Systems MB26
Summary of Contents for Alliance Laundry Systems MB26
- Page 1 Washer-Extractors Barrier Washers Refer to Page 7 for Model Identification Original Instructions Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. D1612ENR3 www.alliancelaundry.com June 2016...
-
Page 3: Table Of Contents
PUTTING THE MACHINE INTO OPERATION..........51 © Copyright 2016, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. - Page 4 PUTTING THE MACHINE OUT OF SERVICE........62 DISCONNECTING THE MACHINE.............62 MACHINE DISPOSAL.................62 POSSIBILITY OF THE MACHINE DISPOSAL BY THE SPECIALIZED COM- PANY...................... 62 POSSIBILITY OF THE MACHINE DISPOSAL BY OWN POTENTIAL..62 © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
-
Page 5: Replacement Parts
Alliance Laun- dry Systems at +1(920)748-3950 for the name and address of the nearest authorized parts distributor. © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 6: Customer Service
For technical assistance, contact your local distributor or contact: Alliance Laundry Systems Shepard Street P.O. Box 990 Ripon, Wisconsin 54971-0990 U.S.A. www.alliancelaundry.com Phone: +1(920)748-3121 Ripon, Wisconsin +32 56 41 20 54 Wevelgem, Belgium © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 7: Model Identification
MODEL IDENTIFICATION MODEL IDENTIFICATION Information in this manual is applicable to these models: MB26 MB33 MB44 MB66 LMA260_MICRO LMA330_MICRO LMA440_MICRO LMA660_MICRO © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 8: Warnings And Labels
It is up to the user to proceed as careful as pos- ARISE IN THE SURROUNDING AIR. WATCH OUT sible. FOR VAPOR THAT ESCAPES FROM THE WASHER EXTRACTOR VENTING! C020 © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... - Page 9 7. Heat risks 8. Description of qualities for ventilation 9. Loss of stability 10. Electric risks 11. Minimal water level 12. Sight holes 13. Water supply © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
-
Page 10: Symbols On The Machine (Depending On The Machine Model)
Warm water inlet (label is red) Indicates that the holes Should be drilled not punched CHM2490N_SVG CHM2446N_SVG Soft cold water inlet (label is light blue) Steam CHM2447N_SVG CHM2445N_SVG © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 11: Micro Control
CHM1636R CHM1646R DECREASING SEQUENCE TIME SPEED Adjustment CHM1635R CHM1647R INFO (overview available wash programs and ENTER - Selection or Confirmation wash sequence functions) CHM1642R CHM1637R © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 12: Operating Instructions
Opening the door, while reducing the hand pressure on the door. First phase of open- ing the door. Press safety pin spring. Table continues... Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... - Page 13 (please see the figure above) you confirm that by another pushing of Start button. In case you are not sure of proper locking - push Stop button and the programme will not be started. © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
-
Page 14: Program Selection
30°C ECONOMY chine starts. wash level START THE WASHER EXTRACTOR Wash program 10: Hot wash 90°C SUPER ECON- OMY level MICRO CONTROL Table 1 continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 15: End Of Wash Cycle
HOW TO OPEN DOOR WHEN FAILURE OCCURS See Installation and maintenance manual. © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 16: First Service At Technical Problem
At loading parameters Stall prev Stall prevention function active Continue At spin sequence Wrong Softw Wrong software version Don’t start New software version Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... - Page 17 At spin sequence brake is closed. Run Free Run Run Status inverter =1 while brake Full stop + safety time At spin sequence is closed. Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 18 (Barrier Washers only) RTC Low Batt Real Time Clock, No Battery or bat- For Info only. For Info only. tery low power (Barrier Washers only) Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 19 Problem writing DAQ Memory For Info only Traceability function, whole cycle E552 DAQ FULL DAQ Traceability Memory is Full For Info only Traceability function, whole cycle Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 20 DAQ Traceability Memory is al- For Info only Traceability function, whole DAQ>PC most Full cycle E600- SOFTW ERR Software Error Full stop + safety time Any time E628 © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
-
Page 21: Important Safety Instructions
All drain, inlet, electrical connections, ventilation, ces give off vapors that could ignite or explode. groundings and other connections must be done in according © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... - Page 22 PLEASE NOTE: Except as necessary to perform a particular in servicing a product, the electrical pow- er supply should ALWAYS be disconnected when servicing a product. © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 23 If the door safety lock does not work, do not use washer until the door lock mechanism is repaired. C189 © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
-
Page 24: Symbols On The Machine
© Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 25: Technical Specification
-6% do +10% of the voltage supply ±1 Hz Motor output kW / HP 4 / 5.36 7.5 / 10.06 – 380-480V INPUT POWER Electrical heating 18 kW Table 2 continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... - Page 26 El. heating 45 kW (380-440V 3AC) El. heating 45 kW (208-240V 3AC) El. heating 54 kW (380-440V 3AC) WASHING FUNCTIONS Washing Distribution Table 2 continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 27 5 to 35 / 41 to 95 Relative humidity 30% to 90% without condensation Height above sea level m / ft up 1000 / 3280 Table 2 continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 28 (1) maximum dimensions including protruding parts (2) maximum dimensions for execution with heat and noise isola- tion (on request) (3) washers with air operated water valves (4) ISO 3744 © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
-
Page 29: Dimensions And Placement Of Components Of The Washers
1060 / 41.73 1060 / 41.73 1170 / 46.06 and noise iso- ≈1160 / 45.67 lation 40 / 1.57 Table contin- ues... Table contin- ues... © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... - Page 30 1560 / 61.42 1560 / 61.42 1610 / 63.39 33 / 1.30 (1) maximum dimensions for execution with heat and noise isola- tion (on request) © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
-
Page 31: Dimensions And Placement Of Components Of The Washer
DIMENSIONS AND PLACEMENT OF COMPONENTS OF THE WASHER Placement of components on the machine 66 / 146 / 663 [kg / lb / L] Figure 6 © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... - Page 32 22. Button of drum positioning 217 / 8.54 23. Unload side door (rear, clean side of the washing machine) 170 / 6.69 24. Door brace Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 33 36. Drain valve, applicable for version with weighing system, (on request) 37. Heating switch (electrical heating, steam heating) 38. Plastic box for electrical connection to liquid soap pumps © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
-
Page 34: Installation
REQUIRED MACHINE WORKING CONDITIONS See Chapter “TECHNICAL SPECIFICATION”. The washer must not be installed or stored in an area where it will be exposed to © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 35: Machine Positioning
THE MACHINE MUST ALWAYS BE FIXED TIGHTLY TO THE FLOOR AND MUST FIT RELIABLY TO THE FLOOR IN ALL FOUR SPOTS INTENDED FOR FIXING THE MACHINE! C195 © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... - Page 36 1. Longitudinal profile of lower frame 2. Floor 3. Mechanical anchor 4. Machine lower cover 5. Nut (part of anchor) 6. Washer (part of anchor) Figure 8 © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
-
Page 37: Installation Of Weighing System Components
C166 10. Using the Advanced menu » Weighing » load cell calibra- tion, check that the machine load is equally shared between the load cells. © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... - Page 38 (see 5. FINE LEVELING THE MACHINE). Each load cell can be ad- justed 5mm). © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 39 INSTALLATION Figure 9 © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 40 The machine is lifted up and the components firm- The load cells and the feet are transported unattached to prevent ly fixed to their places. damage due to shock loads during transport. © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 41 (the machine is not run- ning and the inlet valves are closed), the water connection is not © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
-
Page 42: Connections
For connection dimensions see Figure 5 , Figure 6 . Use the water inlet hoses that accompany the washer as they Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... - Page 43 There are a lot of things that have influence on the temperature measurement. © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 44 • Deflate 2l of water before taking sample. • Sample only after the drum stops and the water temperature in the drum gets calm. © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 45 VALVE AND CAN CAUSE ITS LEAKAGE. C203 For dimensions of steam connection information, see Figure 5 Figure 6 and technical information Table. Use inlet steam pres- © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 46 In some countries an RCD is known as an “earth leakage trip” or utor for more information. “Ground Fault Circuit Interrupter” (GFCI) or an “Appliance Leakage Current Interrupter” (ALCI) or “earth (ground) leakage current breaker”. Specifications: © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 47 11 [4] 40A (40A) 32A (30A) 9 [6] 9 [6] 63A (-) 50A (50A) 7 [10] 7 [10] 5 [16] 5 [16] Table 6 continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 48 66 / 146 / 663 200-240 50-60 3 (L1, L2, L3) 380-415 50-60 3 (L1, L2, L3) 440-480 50-60 3 (L1, L2, L3) Table 7 © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 49 The protection conductor, enabling this connection, is not includ- ed with the washer. If there are other washers/appliances with ex- © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
- Page 50 (max. 5) of Ø 8 mm / 0.315" in the plastic hose connection part © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
-
Page 51: Putting The Machine Into Operation
4. A check of the protective connection (earthing/ground) - “PE” or “PEN”. 5. A check of the vibration switch function during extracting and the emergency function. © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... - Page 52 Transport braces • Package of parts applicable for version with weighing sys- tem. See addition to Installation, maintenance and User´s manual, part number D1603. Figure 26 © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
-
Page 53: Maintenance
8. If there is the earth leakage trip installed in the inlet circuit of the laundry electric switch board, test it according to Chapter "EARTH LEAKAGE TRIP OF THE LAUNDRY". © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 54: Every 6 Months, Or After 1000 Operating Hours
Left vi- limiter. bration switch is bolted to the vertical side of the machine left stand. © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 55: Tightening Moments
TIGHTENING MOMENTS VALUES OF BOLTS, (FIGURE: "MARKING OF THE BOLTS") DIMEN- NUMBER BOLT SION OF pcs. TIGHTENING MOMENTS (Nm) TIGHTENING MOMENTS (lbf.ft) M12 x 60 Table 9 © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 56: Lubrication
TION PERIODS ing bolt. If the belts are too tight the bearing seatings are under stress and their life service has been shortened. • LUBRICANT: © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 57: Water And Steam Filters
3. Clean the sieve with running water or with compressed air. 4. Put the sieve (2) and gasket (3) back to the filter body (1) and tighten the plug (4). © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 58: Thrust Of Door Seal
33 . Adjustment is performed by turning the nuts (1) by the same number of threads always at the same time on the opposite guid- © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 59: Replacement Of Washer Fuses
The earth leakage trip is a very sensitive device and it provides safety for operators by avoiding a risk of an electric shock while the machine is in operation. © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 60: Trouble Shooting Aids
When the power supply has been interrupted during a washing cycle the door lock stays in a blocked position and the door is not openable. © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 61: List Of Recommended Spare Parts
Heating element • V-belts • Door seal Find more detailed information and order codes in the Parts man- ual for individual machines or contact your distributor. © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT... -
Page 62: Putting The Machine Out Of Service
POSSIBILITY OF THE MACHINE DIS- POSAL BY THE SPECIALIZED COMPA- Information concerning the WEEE-directive (Waste Electrical and Electronic Equipment; for European Union member states only): © Copyright, Alliance Laundry Systems LLC - Part No. D1612ENR3 DO NOT COPY or TRANSMIT...
Need help?
Do you have a question about the MB26 and is the answer not in the manual?
Questions and answers