Table of Contents
Advertisement
Washer-Extractors
Commercial Hardmount
Refer to Page 11 for Model Identification
Original Instructions
Keep These Instructions for Future Reference.
CAUTION: Read the instructions before using the machine.
(If this machine changes ownership, this manual must accompany machine.)
Part No. D1599ENR16
www.alliancelaundry.com
November 2023
Advertisement
Table of Contents
Related Manuals for Alliance Laundry Systems AR105M X CONTROL
Summary of Contents for Alliance Laundry Systems AR105M X CONTROL
- Page 1 Washer-Extractors Commercial Hardmount Refer to Page 11 for Model Identification Original Instructions Keep These Instructions for Future Reference. CAUTION: Read the instructions before using the machine. (If this machine changes ownership, this manual must accompany machine.) Part No. D1599ENR16 www.alliancelaundry.com November 2023...
-
Page 3: Table Of Contents
Three-Phase Connections................53 © Copyright 2023, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. - Page 4 Emergency Unblocking of Door Lock.............73 Care of Stainless Steel................... 74 Disposal of Unit..................75 Disconnecting the Machine................75 Disposal of Unit....................75 China Restriction of hazardous substances (RoHS)....... 76 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
-
Page 5: Safety Information
NOTE: The word “NOTE” is used to communicate in- stallation, operation, maintenance or servicing informa- tion that is important but not hazard related. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... - Page 6 Do not install the machine over an open water stor- age or drain system. Adequate ventilation must be provided to avoid the back flow of gases into the room from appliances burning other fuels. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 7 Old hose sets should not be reused. The machine is not designed for use in IT networks. Applicable measures need to be provided. Electrical - Energy Prevention © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 8 Avoid contact with hot inlet water temperatures high- er than 125° Fahrenheit [51°C] or hot surfaces. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 9 • Always contact your dealer, distributor, service agent or the manufacturer on any problems or conditions you do not understand. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 10 NOTE: If literature or replacement parts are required, contact the source from which the machine was pur- chased or contact Alliance Laundry Systems at +1 (920) 748-3950 for the name and address of the nearest authorized parts distributor.
-
Page 11: Introduction
LAE105T LAX520X AR280N_X_CON- PAN030X LAE105X LAY080T TROL_PLUS AR350_X_CONTROL PAN040T LAE135T LAY080X AR350_X_CONTROL_PLUS PAN040X LAE135X LAY105T AR520_X_CONTROL PAN055T LAE180T LAY105X AR520_X_CONTROL_PLUS PAN055X LAE180X LAY135T Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... - Page 12 RX280N_X_CON- LAU080X PAC280X TROL_PLUS TROL_PLUS MWCX30_X_CONTROL RX350_X_CONTROL LAU105T PAC332T MWCX30_X_CON- RX350_X_CONTROL_PLUS LAU105X PAC332X TROL_PLUS MWCX55_X_CONTROL RX520_X_CONTROL LAU135T PAC520T MWCX55_X_CON- RX520_X_CONTROL_PLUS LAU135X PAC520X TROL_PLUS Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 13 SAE135D NX180M_X_CONTROL NX105M_X_CONTROL PAY240T SAE240D NX180M_X_CON- TROL_PLUS NX105M_X_CON- PAY332X PAY520X NX240_X_CONTROL TROL_PLUS NX135_X_CONTROL NX135M_X_CONTROL NX135M_X_CON- NX240M_X_CONTROL TROL_PLUS NX240M_X_CON- NX280_X_CONTROL NX280M_X_CONTROL NX280M_X_CON- TROL_PLUS TROL_PLUS Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 14 UAM180I UAC240I UAU240I UAX240I UAH240I UAR240I UAM240I UAC280I UAU280I UAX280I UAH280I UAR280I UAM280I UAC332I UAU332I UAX332I UAH332I UAR332I UAM332I UAC520I UAU520I UAX520I UAH520I UAR520I UAM520I © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 15 * can be character C - U - E - N - X - H - Y - K - M - can followed by 11 digits or characters © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
-
Page 16: Serial Plate Location
The serial plate is located on the rear panel of the machine and on the frame inside the machine. Always provide the machine serial number when ordering parts or when seeking technical assistance. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 17: Manufacturing Date
2022 2023 2024 Table 1 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 18: Specifications And Dimensions
[kg] (200G) Shipping 320 [145] 408 [185] 441 [200] 595 [270] 639 [290] 672 [305] 992 [450] 1257 [570] weight, lbs. [kg] (100G) Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... - Page 19 18.31 [465] 18.31 [465] 18.31 [465] 18.31 [465] door bot- tom above floor, in. [mm] Drive Train Information Number of motors in drive train Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 20 15-87 [1-6] 15-87 [1-6] 15-87 [1-6] 15-87 [1-6] and Maxi- [100-600] [100-600] [100-600] [100-600] [100-600] [100-600] [100-600] [100-600] mum Water pressure, PSI [bar] [kPa] Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 21 [kN] (150G) Maximum 427 [1.9] 495 [2.2] 607 [2.7] 899 [4.0] 1012 [4.5] 1101 [4.9] static load on floor, lbs. [kN] (200G) Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 22 [3.73 [3.64 [3.40 ± 4.9] [3.40 [5.07 sure lbs./ft ± 3.40] ± 3.98] ± 4.26] ± 4.31] ± 5.31] ± 6.22] [kN/m (100G) Table continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 23 °F [°C] Relative 30%-90% without condensation Humidity Height up to 3280 [up to 1000] above sea level ft. Storage 34-131 [1-55] Tempera- ture, °F [°C] © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
-
Page 24: Machine Dimensions
22. Drain valve or recycle valve - 3 in. [76 mm] (80 lb. / 332 L and 120 lb. / 520 L Models only) 23. Drain valve - 3 in. [76 mm] Figure 2 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... - Page 25 11.93 [303] 15.08 [383] 14.29 [363] 16.34 [415] 19.88 [505] 19.88 [505] 24.61 [625] 24.61 [625] 24.61 [625] 26.42 [671] 26.41 [671] Table 3 continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
-
Page 26: Mounting Bolt Hole Locations
18.66 [474] 22.59 [574] 22.40 [569] 28.11 [714] 31.06 [789] 2.71 [69] 2.85 [67.5] 2.65 [67.5] 2.74 [69.5] 2.74 [69.5] 2.74 [69.5] Table 4 continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... - Page 27 36.38 [924] 2.74 [69.5] 2.74 [69.5] 2.74 [69.5] 2.76 [70] 2.76 [70] 8.68 [220.5] 8.68 [220.5] 8.68 [220.5] 10.69 [271.5] 10.69 [271.5] Table 5 continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
-
Page 28: Floor Mounting Layout
41.71 [1059.5] 37.82 [960.5] 49.04 [1245.5] 3.23 [82] 3.23 [82] 3.23 [82] 3.23 [82] 3.23 [82] Table 5 Floor Mounting Layout Dimensional Clearances CZW110N Figure 5 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... - Page 29 20 [500] (minimum) Distance above 31.50 [800] 31.50 [800] 31.50 [800] 45.28 45.28 45.28 41.34 52.36 machine (mini- [1150] [1150] [1150] [1050] [1330] mum) Table 6 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
-
Page 30: Installation
The machine's side panel can be damaged. NOTE: Two self-adhesive rubber stop-blocks are supplied with the machine. They may be applied as paint protection when opening the door. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 31: Machine Installation
11. Allow concrete to cure for at least one week before installa- size] for the perimeter reinforcing bar into the existing floor. tion of the machine. 5. Clean out debris from each reinforcing bar hole. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... - Page 32 Refer to Table 4 or Table 5 , Specification G 2.95 [75] 31.12 31.12 35.65 37.74 43.48 46.44 42.54 53.76 [790.5] [790.5] [905.5] [958.5] [1104.5] [1179.5] [1080.5] [1365.5] Table 8 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
-
Page 33: Machine Installation On Floor Or Steel Base
2. Washers; 60mm external diameter, 16.5mm internal diameter, 6mm thickness; supplied with the machine 3. Spacing washer 4. Anchor bolt 5. Washing machine 6. Concrete floor Figure 8 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... - Page 34 (80 x 80 mm). 3. Fit a washer and self-locking nut on the anchor bolt and tight- en with a torque wrench to 100Nm. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 35 18 kg / 40 lb. / 180 L, 24 kg / 55 lb. / 240 L and 28 kg / 70 lb. / 280 L with 200 G Extraction; 35 kg / 80 lb. / 332 L and 52 kg / 120 lb. / 520 L CHM2474N_SVG 1. Washing machine 2. Spacing washers, as needed 3. Concrete floor Figure 11 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
-
Page 36: Machine Grouting (North American Models Only)
M16 during installation W945 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 37: Drain Connection
Avoid sharp bends which may prevent proper draining. The drainage pipe should be located over a floor drain, drainage channel. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... - Page 38 0.79 [20] 0.79 [20] 0.79 [20] D mini- 3.94 [100] 3.94 [100] 3.94 [100] 3.94 [100] 3.94 [100] 3.94 [100] 3.94 [100] 3.94 [100] Table 9 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 39 If the main drain pipe cannot be sufficiently ven- must have dimensions suitable for double the value of water flow. ted, install a vent per machine. Every time a machine is coupled © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 40 Drain Line Sizing / Minimum Drain ID, in. [mm] A - 1 Machine B - 2 Machines C - 3 Machines 3 [75] 4 [100] 5 [125] Table 11 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
-
Page 41: Drain Pump, 7.5 Kg / 20 Lb. / 75 L Models Outside Of North America
In order to achieve good draining, the hose must not bend at a sharp angle. Refer to Figure 15 . CHM2514N_SVG 1. Drain hose bend Figure 15 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 42: Water Connection Requirements
18 kg / 40 lb. / 180 L and 24 kg / 55 lb. / 240 L Models, to connect cold water, use a hose with plastic elbow. To connect hot water, use a hose with metal elbow. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... - Page 43 1. Refer to Table 12 . 2. Refer to Table 12 . 3. Refer to Table 12 . Figure 19 Water type Water connection Table 12 continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 44 Suitable air cushions (risers) should be installed in supply lines to prevent “hammering.” Alliance Laundry Systems, LLC ranges of front loading commer- cial clothes washing machines have solenoid valves at the inlets. The machines are supplied with approved inlet hoses.
-
Page 45: Connecting Hoses
5. Install this end of hose to water supply tab (Black colored 7. Continue tightening and rechecking until no leaks are found. coupling for BSPP thread) 6. Filter Screens 7. Dual Check Valves Figure 20 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 46: Water Reuse System
A pump must transport the recuperated water from the tank to the Connection - outside diam- 0.75 [19] washer. The requirements for the pump depend on the number eter, in. [mm] © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 47: Electrical Installation Requirements
When you have long distances in the electrical installation, it may be necessary to use big- ger cables to reduce the voltage drop. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 48: Residual Current Device (Rcd) - Models Outside Of North America
6. Protective conductor 7. Main switch inlet terminal switchboard 8. Neutral conductor Figure 23 IMPORTANT: Alliance Laundry Systems warranty does not cover components that fail as a result of improper input voltage. Residual Current Device (RCD) - Models Outside of North America... -
Page 49: Supply Cable
(6) for L1/U, (L2/V), (L3/W), (N) conductors. Make sure there is no accidental contact, since the supply ca- ble stays under voltage even when the main switch is off. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 50: Machine Protective Earth Connection And Equipotential Bonding
14 ). However, for the protection purposes, with the supply cable Figure 25 cross section of a min. 4 mm , select a larger conductor section, i.e., 6 mm © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 51: Input Power Conditioning
Three-phase machines require a separate, three-phase in- Connect the electrical service's wires to the machine's electrical verse-time circuit breaker to prevent damage to the motor by dis- connection terminal as shown. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... - Page 52 Models outside of North America with Single-Phase North American Models with Single-Phase Connec- Connection tion PE U N PE L1L2 CHM2500N_SVG Figure 30 CHM2497N_SVG Figure 28 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
-
Page 53: Three-Phase Connections
Table 19 continues... ing facility. If, at installation, the nominal supply voltage is lower, the appropriate voltage terminal on the transformer must be se- © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 54: Thermal Overload Protector
208V, redirect the voltage wire to the 208V terminal. Thermal Overload Protector For models with inverter drives, the inverter drive provides over- load protection for the drive motor. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 55: Electrical Specifications - Models Outside Of North America
L3, N) 12.6 (6) 17 (9) 380-415 50/60 3 (L1, L2, 11.7 (6) 16.2 (9) 440-480 50/60 3 (L1, L2, 13.5 (7) 15.5 (9) Table 20 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... - Page 56 3 (L1, L2, 0.65 12.6 (6) 17 (9) 12.6 21.3 (12) 440-480 50/60 3 (L1, L2, 0.65 12.3 (7) 15.7 (9) 12.6 20 (12) Table 21 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 57 12.9 (6) 17.2 (9) 12.8 21.5 (12) 14.6 13.8 (22.5) 32 440-480 50/60 3 (L1, L2, 0.85 12.2 (7) 15.9 (9) 12.8 20 (12) Table 22 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 58 Standard Electric Heat 200-240 50/60 2 (L1, L2, or L1, N) 200-240 50/60 3 (L1, L2, 12.9 36.2 (12) 18.9 53 (18) Table 24 continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 59 31 (18) 380-415 50/60 3 (L1, L2, 12.9 20.7 (12) 18.9 29.7 (18) 440-480 50/60 3 (L1, L2, 12.9 19.4 (12) 18.9 27.4 (18) Table 24 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 60 2 (L1, L2, or L1, N) 200-240 50/60 3 (L1, L2, 53 (18) 380-415 50/60 4 (L1, L2, 31.7 (18) L3, N) Table 26 continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 61 (21.9) 380-415 50/60 3 (L1, L2, 19.3 30 (18) 23.2 38 (21.9) 440-480 50/60 3 (L1, L2, 19.3 29 (18) 23.2 35 (21.9) Table 27 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 62 (21.9) 380-415 50/60 3 (L1, L2, 19.3 30 (18) 23.2 38 (21.9) 440-480 50/60 3 (L1, L2, 19.3 29 (18) 23.2 35 (21.9) Table 28 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 63 200-240 50/60 2 (L1, L2 or L1, N) 200-240 50/60 3 (L1, L2, 16.5 (40.6) 380-415 50/60 3 (L1, L2, 62.9 (40.6) Table 30 continues... © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
- Page 64 Installation Standard Electric Heat 440-480 50/60 3 (L1, L2, 81.5 (40.6) Table 30 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
-
Page 65: Electrical Specifications - North American Models
AWG (mm Code cy (Hz) Phase Wire Amps (A) CSA (A) X and Z 208-240 2 (L1, L2 or 14 (2.5) L1, N) Table 34 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 66: Steam Requirements (Steam Heat Option Only)
(min 1h) to allow to cooldown the steam system. Then turn the connection nut slowly loose until some pressure es- capes. Wait until the escape stops, then disconnect further. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 67: Steam Valve Installation
Secure the location of the wiring and hoses so they can not be pinched, damaged or rubbed. Before you start to use liquid soap, © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 68: Connection Of External Liquid Supplies
(check the clamps). Any chemical leakage may cause serious damage to the washer. If one of the connec- tions is open, close and secure the opening with an ap- propriate cover. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... - Page 69 Installation Chemical Injection Supply System 1. Injection Point 2. Chemical Dispenser Pump Outlet 3. PVC Pipe Figure 36 © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
-
Page 70: Operation
• If the machine is a coin operated unit, add coins. As each coin is added, the vend counts down to the amount re- maining. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 71: Before Washing
"CONTINUE / STOP" appears as soon as the power supply is re- stored. If you press the STOP button, the wash program will be cancelled. If you press the START button, the wash program will © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 72: Maintenance
2. Clean the door glass and between the door gasket and the door with a damp cloth. 3. Clean supply dispenser lid and general area with mild deter- gent. Flush the dispenser with clean water. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 73: Every 6 Months
Emergency Unblocking of Door Lock NOTE: Read Important Safety Instructions first. 1. Verify if all condition are present to safely open the door. 2. Remove front panel. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 74: Care Of Stainless Steel
Locate the pump and tubing below the machine’s injection point to prevent siphoning of chemicals into the machine. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 75: Disposal Of Unit
For more detailed information about recycling of this product, please contact the local city office, household waste disposal service, or the source from which the product was purchased. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT... -
Page 76: China Restriction Of Hazardous Substances (Rohs)
NOTE: The referenced Environmental Protection Use Period Marking was determined according to normal oper- ating use conditions of the product such as temperature and humidity. This product under normal use, durable years of environmental protection is 15 years. © Copyright, Alliance Laundry Systems LLC - Part No. D1599ENR16 DO NOT COPY or TRANSMIT...
Need help?
Do you have a question about the AR105M X CONTROL and is the answer not in the manual?
Questions and answers
Do The drain valve transformer how much voltage ......220v or 180v .....?
The voltage of the drain valve transformer for the Alliance Laundry Systems AR105M X CONTROL depends on the supply voltage. If the supply voltage is 220V, the transformer terminal should be set to 240V, and if the supply voltage is 180V, the transformer terminal should be set to 208V. Therefore, the transformer is not specifically 220V or 180V, but must be set to the appropriate terminal based on the actual supply voltage.
This answer is automatically generated
Machine when start start switch not functioning
The start switch on the Alliance Laundry Systems AR105M X CONTROL machine may not be functioning due to a power cut. When power is restored, the machine displays "PRESS START / OPEN DOOR" or "CONTINUE / STOP" depending on the model. If the door is opened, the program is canceled. If START is not pressed, the program does not continue.
This answer is automatically generated
When start showing add soap
The Alliance Laundry Systems AR105M X CONTROL displays an "add soap" message when a "Pause" has been programmed at the end of a wash sequence. During this pause, the machine stops, displays "Pause, Press Start to Continue," and sounds a buzzer. Opening the soap door turns off the buzzer, allowing the operator to add soap before continuing.
This answer is automatically generated