Carrier 30WG Operation Instructions Manual page 22

Pump Configuration Menu – PUMPCONF (continued)
No. Point name Status
5
6
7
8 clpmpdel 24 to 3000
9 clpmpper no / yes
10 clpmpsby no / yes
11 clpmploc no / yes
12
13 cdpmpseq 0 to 4
14
15
16
17
18
19 cdpmpdel 24 to 3000
20 cdpmpper no / yes
21 cdpmpsby no / yes
22 cdpmploc no / yes
23 ol_pump no / yes
*Depends on the selected language (English by default).
Heat/Cool Config Menu – HCCONFIG
No. Point name Status
1 cr_sel 0 to 3
2 hr_sel 0 to 3
3
4
5 boil_on no / yes
6 boil_th -15 to 15
7 ehs_th -4.90 to 21.42
8 both_sel no / yes
9 ehs_back no / yes
10 ehs_pull 0 to 60
*Depends on the selected language (English by default).
HDC Configuration Menu – HDC_CONF
No. Point name Status
1 adpmpper no / yes
2 summ_oat 15.0 to 30.0
3 summ_on 0 to 12
4 summ_off 0 to 12
22
Default Unit Displayed text*
2 = Two Pumps Auto
3 = Pump#1 Manual
4 = Pump#2 Manual
48 hour Pump Auto Rotation Delay
no - Cool Pump Anti-Sticking
no - Cool Pump Stopped in Sby
no - Flow Checked if Pump Off
CONDENSER PUMP
0 - Condenser Pumps Sequence
0 = No Pump
1 = One Pump Only
2 = Two Pumps Auto
3 = Pump#1 Manual
4 = Pump#2 Manual
48 hour Pump Auto Rotation Delay
no - Cond Pump Anti-Sticking
no - Cond Pump Stopped in Sby
no - Flow Checked if Pump Off
no - Open loop pump Control
Default Unit Displayed text*
0 - Cooling Reset Select
0 - Heating Reset Select
0=none, 1=OAT,
2=delta T, 3=4-20mA
no Boiler Manual Command
-10 °C Boiler OAT Threshold
5.2 °C Elec Stage OAT Threshold
no - HSM Both Command Select
no - 1 Elec Stage for Backup
0 min Electrical pulldown time
Default Unit Displayed text*
no - Add. Pump Anti-Sticking
20.0 °C Summer OAT threshold
5 hour Summer OAT start delay
5 hour Summer OAT stop delay
Description
2 = Two Pumps Auto (units with two pumps)
3 = Pump#1 Manual
4 = Pump#2 Manual
Pump auto rotation delay (units with two
pumps = auto control)
Evaporator pump anti-sticking protection
Not applicable (please ignore this parameter)
Water flow is checked when the pump is off
CONDENSER PUMP
Condenser pump sequence
0 = No Pump
1 = One Pump Only
2 = Two Pumps Auto (units with two pumps)
3 = Pump#1 Manual
4 = Pump#2 Manual
Pump Auto Rotation Delay (units with two
pumps = auto control)
Condenser pump anti-sticking protection
Not applicable (please ignore this parameter)
Water flow is checked when the pump is off
Open loop pump control
Description
Cooling reset selection
Heating reset selection
0 = None, 1 = OAT,
2 = Delta T, 3 = 4-20 mA control
Boiler manual command:
No = boiler control based on OAT control logic
(see boil_th below)
Yes = boiler control enabled if OAT sensor is
NOT present or the sensor fails
Boiler OAT threshold
Electric heating stage, OAT threshold
HSM both command selection
One electric heating stage used for back-up
Electrical pull-down time
Description
Additional pump anti-sticking protection
This threshold defines when Summer mode
can be started
Summer mode is activated if OAT is above
OAT Threshold [sum_oat] for at least the
sum_on delay
Summer mode is reset when OAT goes below
OAT Threshold [sum_oat] minus 2K for at least
the sum_off delay