Malmbergs 99 190 21 Installation And Instruction Manual

1. Technical Specifications
Product type Independent PIR DALI sensor (Daylight harvest)
Operating voltage 220~240VAC 50/60Hz
Switched power Maximum 20pcs DALI devices Maximum 40mA
Power consumption < 1W
Detection angle 360
Detection area (DxH) 10 x 3m (Tangential)
Mounting height 5m (Maximum)
Detection range 10% / 50% / 75% / 100%
Hold time 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min
Stand-by time 0s / 10s / 1min / 5min / 10min / 30min / 1h / +
Stand-by dimming level 10% / 20% / 30% / 50%
Daylight threshold 50 ~ 500Lux , Disable
Warmming-up time 30s
o
Operating temperature -20
3. Rotary Switch Settings
A rotary switch is built inside the sensor for
scene selection / fast programming. Total
16 channels available:
Detection Hold
Channel
range time
0 100% 5s
1 100% 1min
2 100% 5min
3 100% 5min
4 100% 5min
5 100% 5min
6 100% 10min
7 100% 10min
8 100% 10min
9 100% 10min
A 100% 20min
B 100% 20min
C 100% 30min
D 100% 30min
E 100% 30min
F 100% 5s
Note: settings can also be changed by remote control 99 190 27. The last action controls.
4. Functions
4.1 Daylight Harvest (Daylight Regulating)
Daylight sensor measures the available surrounding natural light, calculates how much electrical light is
needed to reach the total lux expected. The demand is given to the LED driver by DALI signal, so as to
deliver the needed amount of electric light.
Light level
Energy Saving Zone
0
4.2 Lux Off Function
The built-in daylight sensor can read ambient natural light and switch off the fixture automatically whenever
artificial light is not required (natural light lux level exceeds daylight threshold).
Note: if the stand-by time is preset at "+∞", the fixture never switches off even when natural light is
sufficient.
www.malmbergs.com
Art.no: 99 190 21
FLUSH MOUNT PIR DALI SENSOR 99 190 21
Installation and Instruction Manual
o
o
C ~ +50 C
Rotary switch preset (Please
see the location in 2. Installation)
Stand-by Stand-by
time dimming level
10s 10%
5min 10%
10min 10%
+∞ 10%
+∞ 10%
+∞ 30%
30min 10%
+∞ 10%
+∞ 10%
+∞ 30%
1h 10%
+∞ 30%
+∞ 10%
+∞ 30%
+∞ 50%
10s 10%
Hold time
Stand-by time
4 2
2. Installation
Warnings:
1. Installation of the sensor involves connecting it to the mains supply. This work must be
2. Disconnect supply before installing.
Infrared receiver
Rotary switch preset
Daylight
threshold
Disable
Varning!
50Lux
Stäng av strömmen, ta ut säkringen på elcentralen eller ställ automatsäkringen till läge "AV",
50Lux
innan installationsarbetet påbörjas.
75Lux
Skall installeras av behörig installatör och i enlighet med gällande föreskrifter.
100Lux
200Lux
4.3 Semi-auto Function (Absence Detection)
50Lux
The motion sensor is employed, but only activated on the manual press of the push switch,
75Lux
light keeps on in the presence, and dims down in the absence, and eventually switches off
100Lux
automatically in the long absence.
200Lux
100Lux
4.4 Ambient Daylight Threshold
200Lux
Switch the power supply to the sensor two times within 2 seconds, the ambient lux level is
100Lux
sampled and set as the new daylight threshold. Both the settings on rotary switch and the
200Lux
ambient lux level sampled can overwrite each other. This feature enables the daylight sensor
400Lux
to be commissioned to the environment in which it is installed. The last adjustment remains in
100Lux memory.
4.5 8H Manual ON Mode For LED Lamp
Turn off/on the power supply three times within 3 seconds, the light will be turned on for 8
hours, even there is no motion detected, then go back to sensor mode automatically.
Note: this 8H manual on mode can be cancelled by turning off/on the power supply one time
within 1 second.
4.6 Manual Override
With the help of push-switch, this sensor maybe over-ridden by the end-users to switch on/off
the lights manually, or adjust the light brightness during motion hold-time. This makes the
product more user-friendly and offers more options to fit for extra-ordinary demands.
* Short push (<1s): on/off function;
ON → OFF: the light turns off immediately and cannot be lighten for a certain time (equals
to hold time preset) even there is movement is detected. After this period, the sensor goes
back to auto sensor mode.
Normal Electric Light
OFF → ON: the light turns on 100% and goes to auto sensor mode, even when ambient
Daylight controlled light
* Long push (>1s): adjust the target lux level by turning the light up or down. Both the
Natural light
Time (hrs)
* If no end-user adjustment is desired, simply leave this terminal disconnected.
4.7 Synchronization Function
By connecting the "SYNC" terminals in parallel (see wiring diagram), no matter which sensor
detects motion, all 99 190 21 in the group will turn on the lights when surrounding natural light
is below the daylight threshold. The sensor module is shared and the detection area could be
widely enlarged in this way.
carried out by a specialist in accordance with electrotechnical regulations.
70mm
4
3
Photocell
1
LED indicator
PIR
2
Note: the blind can be plugged to the cover for
Lux level exceeds the daylight threshold.
adjustment on remote control and push switch can overwrite each other,
the last adjustment remains in memory.
64.7
(1) Sensor inset
(2) Lens pluggable
(3) Protection cover (covers the
high-voltage terminals, and leaves
the DALI terminals exposed).
(4) Ceiling (drill hole O 70mm).
Blind
reducing detection angle if necessary
2017.03.01