Advertisement
Quick Links
Instruction Manual IM01005031E
Instruction Manual IM01005031E
Eaton SPD Series
Eaton SPD Series
For Mounting External To
for Mounting External to
Electrical Distribution Equipment
Electrical Distribution Equipment
Effective November 2012
Effective January 2019
Table of Contents
Rev. 2
Rev. 6
Advertisement
Related Manuals for Eaton SPD050208Y1K
Summary of Contents for Eaton SPD050208Y1K
-
Page 1: Table Of Contents
Instruction Manual IM01005031E Effective November 2012 Rev. 2 Instruction Manual IM01005031E Effective January 2019 Rev. 6 Eaton SPD Series Eaton SPD Series For Mounting External To for Mounting External to Electrical Distribution Equipment Electrical Distribution Equipment Table of Contents 1.0 Introduction 2.0 Installation... -
Page 2: Introduction
Rating Feature Package The Eaton SPD Series is designed to mount on the wall (or other vertical surface) as close as possible to the electrical cabinet. The SPD Series is available in voltage ratings from 120-600V AC,... -
Page 3: Installation
OTHER DEVICES OR LEADS. DAMAGE TO THE EQUIPMENT MAY SPD. THE SPD WILL ALSO CAUSE THE TEST TO FAIL. RESULT. Every Eaton SPD Series unit is tested at the factory for dielec- Check the facility grounding system. All grounding, bonding, •... - Page 4 Eaton SPD Series IM01005031E Rev. 2 Eaton SPD Series for Mounting External Instruction Manual IM01005031E - Rev. 6 For Mounting External To to Electrical Distribution Equipment Effective November 2012 Effective January 2019 Electrical Distribution Equipment Determine the wire length for the Ground and Neutral (where applicable) wires and cut these wires as needed.
- Page 5 Eaton SPD Series IM01005031E Rev. 2 Eaton SPD Series for Mounting External Instruction Manual IM01005031E - Rev.6 For Mounting ExternalTo to Electrical Distribution Equipment Effective November 2012 Effective January 2019 Electrical Distribution Equipment Eaton SPD Series IM01005031E Rev. 2 For Mounting ExternalTo Effective November 2012 Figure 3.
- Page 6 Eaton SPD Series IM01005031E Rev. 2 Eaton SPD Series for Mounting External Instruction Manual IM01005031E - Rev. 6 IM01005031E Rev. 2 Eaton SPD Series For Mounting External To to Electrical Distribution Equipment Effective November 2012 Effective January 2019 For Mounting External To...
- Page 7 Eaton SPD Series for Mounting External Instruction Manual IM01005031E - Rev.6 to Electrical Distribution Equipment Effective January 2019 Figure 7. Flush-Mount Plate For 50-200 kA Units In A NEMA 1 Rated Enclosure Eaton www.eaton.com...
- Page 8 Eaton SPD Series for Mounting External Instruction Manual IM01005031E - Rev. 6 to Electrical Distribution Equipment Effective January 2019 BLUE / WHITE COMMON RED / WHITE NORMALLY OPEN ORANGE / WHITE NORMALLY CLOSED Figure 8. Sidemount Form C Wires Figure 11. 3-Phase Wye Units Figure 9.
-
Page 9: Operating Features
Effective January 2019 3.0 Operating Features 3.1 General The Eaton SPD Series comes in three feature packages: Basic, Standard, and Standard with Surge Counter. The operating spe- cifics of each feature package are described below. The Eaton SPD Series requires no operator involvement, other than to monitor the display panel to determine status of the SPD. - Page 10 Effective January 2019 3.2.2 Standard Feature Package 3.2.4 SPD Display Rotation The Eaton SPD Series Standard Feature Package display is The SPD display can be rotated on the SPD enclosure, up to 360 shown in Figure 16 degrees. This allows you to position the display for the best vis- ibility regardless of the position in which the SPD is installed.
-
Page 11: Troubleshooting
Table 2, Troubleshooting Chart. This Troubleshooting Chart identifies possible causes and solutions to the malfunc- tion. Further assistance may be obtained by calling Eaton’s Applications Engineers, at 1-800-809-2772, option 4, sub-option 2, including being directed to the warranty process if applicable. -
Page 12: Specifications
UL1449 4th Edition listed, CSA (excludes 230L voltage code), UL1283 7th Edition (Type 2 SPDs only) IEC 61643-11/EN 61643-11, Part 11: Test Class II. See Section 6.0 Ordering Guidelines for specific models. Warranty 10 Years, 15 Years if you register on www.eaton.com/spd and click the warranty registration icon. ROHS Compliant Wire Length and AWG Factory prewired with 48 inches of 10 AWG wire. -
Page 13: Ordering Guidelines
Surge Counter with Reset Button **Eaton’s Delta Catalog numbers SPD120480D3M, SPD160480D3M and SPD200480D3M meet the requirements of IEC 61643-11 / EN 61643-11, Part 11: Test Class II, and are intended to be installed in applications with a degree of protection rated IP 20. -
Page 14: Warranty
Electrical Distribution Equipment Effective January 2019 7.0 Warranty Eaton warrants these products for a period of 10 years from the date of delivery to the purchaser , 15 years if you register on www.eaton.com/spd and click the warranty registration icon to be free from defects in both workmanship and materials. - Page 15 Eaton SPD Series for Mounting External Instruction Manual IM01005031E - Rev.6 to Electrical Distribution Equipment Effective January 2019 Notese: Eaton www.eaton.com...
- Page 16 THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY ANY CONTRACT BETWEEN THE PARTIES. In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or otherwise for any special, indirect, incidental or consequential damage or loss...