7.0 Warranty .................... 12 Eaton is a registered trademark of Eaton Corporation or its subsidiaries and affiliates. National Electric Code and NEC are registered trade- marks of the National Fire Protection Association. Power Chain Management is a registered trademark of Eaton Corporation, UL is a federally registered trademark of Underwriters Laboratories, Inc.
This manual is organized into seven sections, as follows: 1.4 Catalog Numbering System 1.0 Introduction Each Eaton SPD Series unit has a name plate that identifies the parameters used for manufacture. These parameters are 2.0 Installation expressed in letters and numbers, to reflect the Series, kA 3.0 Operating Features...
Check the facility grounding system. All grounding, bonding, • Every Eaton SPD Series unit is tested at the factory for dielec- and earthing must meet the NEC and any other national, state tric breakdown. No further SPD testing is required for installa- and local electrical codes.
Page 5
Eaton SPD Series Instruction Manual IM01005019E - Rev.5 Surge Protective Device for Integrated Units Effective November 2013 6. Select the correct wiring diagram for the SPD you are install- ing. You must refer to this diagram while wiring the SPD.
Page 6
Eaton SPD Series Instruction Manual IM01005019E - Rev. 5 Surge Protective Device for Integrated Units Effective November 2013 Figure 6. Wiring - Single Phase Units (230 L) Figure 8. Wiring - 3-Phase Delta Units Figure 7. Wiring - Split Phase Units Figure 9.
Eaton SPD Series Instruction Manual IM01005019E - Rev.5 Surge Protective Device for Integrated Units Effective November 2013 7 . Connect the System Ground wire (green) to the SPD’s Surge Ground connection using a ring terminal suitable for use with a #10 fastener and a #10-32 x 3/8" fastener (customer supplied).
Page 8
Eaton SPD Series Instruction Manual IM01005019E - Rev. 5 Surge Protective Device for Integrated Units Effective November 2013 6. Connect the System Ground wire (green) to the SPD’s 2. Connect the RDP cable to the SPD. Use tie wraps Surge Ground connection using a ring terminal suitable (already on the SPD) to secure the cable to the for use with a #10 fastener and #10-32 x 3/8"...
The Eaton SPD Series Standard Feature Package display is 3.1 General shown in Figure 19. The Eaton SPD Series comes in three feature packages: Basic, Standard, and Standard with Surge Counter. The operating spe- cifics of each feature package are described below.
3.2.4 SPD Display Rotation 3.3 Remote Display Panel (RDP) Option The Eaton Series SPD displays may be monitored on a remote The SPD display can be rotated on the SPD enclosure, up to 360 display panel (RDP). This is indicated by the catalog style with a degrees.
Table 3. This Troubleshooting Chart identifies possible causes and solutions to the malfunction. Further assistance may be obtained by calling Eaton’s Applications Engineers, at 1-800-809-2772, option 4, sub-option 2, including being directed to the warranty process if applicable.
UL1449 3rd Edition recognized component for the US and Canada, UL1283 (Type 2 SPDs only) IEC 61643-11/EN 61643-11, Part 11: Test Class II. See Section 6.0 Ordering Guidelines for specific models. Warranty 10 Years, 15 Years if the product is properly registered with Eaton. Eaton www.eaton.com...
IEC 61643-11/EN 61643-11, Part 11: Test Class II, and intended to be installed in indoor applications with a degree of protection rated IP 00. Examplee: SPD 250480D2J = SPD Series, 250kA Per Phase, 480D Voltage, Standard Feature Package, Motor Control Center Application.
THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY ANY CONTRACT BETWEEN THE PARTIES. In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or otherwise for any special, indirect, incidental or consequential damage or loss...