Advertisement
Quick Links
Advertisement
Related Manuals for Casall X200
Summary of Contents for Casall X200
- Page 1 Casall X200 CROSSTRAINER 93001...
- Page 2 Important: Please locate your serial number and record in the box below for service support purposes. Serial number here: ...
- Page 3 X200...
- Page 4 X200 NO.P-19 Spring Washer for handlebar bolt 6(black)(4) No:P-1 Allen Bolt M7*P1.0*30L (2) No:P-4 Spring Washer No:P-2 Regular Washer 7*2t(2) 7*1t(2) NO.P-9Carrage Bolt M8x40mm (4) NO.P-17 Carrage bolt M6*P1.0*40L (black)(4) NO.P-18 Knob (foot pedal)M6*P1.0 (4) NO.P-16 Flat Washer No:P-3 Metal cover (1)
- Page 5 Assembly Diagram P-20...
-
Page 6: Exploded Diagram
EXPLODED DIAGRAM E-4 E-5 E-4 E-5 E-2 E-3 H-12 H-14 H-13 H-11 H-10... -
Page 7: Parts List
PARTS LIST Item spec. Q'ty A , A-1 Computer & Screw for computer 1SET Front handlebar Foam grip for front handlebar 2PCS End cap for foam grip φ7/8" 2PCS Hand pulse WP1007-33B 1SET Screw M3x20L 2 PCS Wire for hand pulse 1 PC Upper handlebar ( L) End cap for upper handlebar (R&L) - Page 8 φ5xφ16x1t F-20 Flat washer 8PCS F-21 Cross disc 2PCS F-22 Round disc 2PCS F-23 Cap for round disc 2PCS F-24~F-31 Crank connation set 2PCS F-32 Nuts for cross disc M10xP1.25x10T 2PCS φ20.5xφ25x7.5mm F-33 Bushing F-34 Bearing 6004RS 2PCS φ20xφ30x0.3t F-35 Wave washer φ20.3xφ30x1t F-36...
- Page 9 M-15,M-16 Right rear cover (upper/down) for pedal post 1SET Adaptor DC Cable P~P-20,Q Bolts & nuts pack 1SET...
-
Page 10: Assembly Steps
ASSEMBLY STEPS STEP 1 1. Attach the Front Stabilizer (pt.J) to the Main Frame (pt.F) using two M8x55L carriage bolts (pt.P- 14),Flat washer (pt.P-13) and nuts (pt.P-12). 2. Attach the Rear Stabilizer (pt.J-4) to the Main Frame (pt.F) using two M8x55L carriage bolts (pt.P- 14),Flat washer (pt.P-13) and nuts (pt.P-12). - Page 11 STEP 3 1. Connect the Computer cables (pt .D-1) to the Computer (pt.A). Then attach the Computer (pt .A) to the Computer bracket with the enclosed Screws (pt. A-1). 4*M5*10 STEP 4 1. Remove the pre-installed Screws (pt.D-2) on the handlebar post first. 2.
- Page 12 Fix the Left and Right lower handlebar (pt.E & E-8) to the Handlebar Post (pt.D) with STEP 5 one Axle (pt.M), two sets of Wave washer (pt.P-8), Gasket (pt.Q) and Flat washers (pt.P-6) and Allen bolt (pt.P-7). 17.5x 25x0.3t M8x20 10* 26*2T...
- Page 13 STEP 6 1. Attach the Left and Right lower Handlebar (pt.E & E-8) to the Left and Right pedal post (pt.L & L-2) using two Allen bolt (pt.P-15), four Flat washers (pt.P-16) and two Nylon nuts (pt.P-11). -- - Figure A 2.
- Page 14 STEP 7 1. Remove the pre-installed screws (pt.L-1) on the Pedal post first. 2. Attach the Lower handlebar (pt.E & E-8 R/L) to the left and right pedal post (pt L & L-2), and then close the cover (pt M-9 & M-10) using screws (pt.P-5 & L-1). 3.
- Page 15 Slide the Upper handlebar post (pt.C,C-3) (R/L) into the Lower handlebar (pt.E,E-8) (R/L) STEP 8 and then fix with the four Carriage bolts (pt.P-9), Semicircle washers (pt.P-10), and Nuts (pt.P-11). M8X40 8X 19X2t STEP 9 Remove the pre-installed screws (pt.E-7) on the Lower handlebar (pt.E,E-8 R/L). Assemble the Cover (Rear &...
- Page 16 STEP 10 Connect the adaptor (N) to the DC hole (located on the back of the chain cover). INSTRUCTIONAL MANUAL FOR CASALL X200 CONSOLE...
- Page 17 DISPLAY FUNCTIONS : ITEM DESCRIPTION TIME .Workout time displayed during exercise. .Range 0:00 ~ 99:59 SPEED .Workout speed displayed during exercise. .Range 0.0 ~ 99.9 KM/Hour DISTANCE .Workout distance displayed during exercise. .Range 0.00 ~ 99.90 KM CALORIES .Burned calories during workout display. .Range 0 ~ 990 Cals * Calorie count on the display only serves as a general guideline.
- Page 18 OPERATION: POWER ON Plug in power supply, computer will power on and display all segments on LCD for 2 seconds. After 4 minutes without pedaling or pulse input, console will enter into power saving mode. Press any key may wake the console up. Manual Mode Adjust resistance during workout manually.
- Page 19 User Program Mode Preset your own workout profile. Press UP or DOWN to select workout program, choose User and press MODE to enter. Press UP or DOWN to set load level of each column, and press MODE to next one. Hold on pressing MODE to finish or quit setting.
- Page 20 Recovery Monitor heart rate recovery status. 1. User must be holding the handgrip. When the pulse value is displayed on the computer, press on the RECOVERY key. 2. TIME shows "0:60" (seconds) and count down. 3. Computer will show F1 to F6 after count down to 0 to test heart rate recovery status. <Trouble shooting>...