1. Manuals
  2. Brands
  3. Casall Manuals
  4. Elliptical Trainer
  5. X600
  6. Assembly instructions manual

Casall X600 Assembly Instructions Manual

Crosstrainer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Casall X600
CROSSTRAINER
93003
1

Advertisement

Table of Contents
loading

Related Manuals for Casall X600

Summary of Contents for Casall X600

  • Page 1 Casall X600 CROSSTRAINER 93003...

  • Page 2: Parts List

    PARTS LIST Item spec. Q'ty A , A-1 Computer & Screw for computer SM2871-67 1PCS Front handlebar φ25.4 1PCS Foam grip for front handlebar 440xφ20x5.0m/m 2PCS φ7/8" End cap for foam grip 2PCS WP1007-33B B-3,B-5 Hand pulse & Cable (600L+600L) 1SET C,C-3 Upper handlebar (R&L)
  • Page 3 F-24~ F-30 Crank connation 2PCS Flywheel set 1SET Magnet system 1SET Front stabilizer 1PCS J-1,J-2 Front transportation wheel 1SET Rear stabilizer 1PCS End cap for rear stabilizer 1SET Idler wheel set 1SET Pedal post (Lift) 1PCS Pedal post (Right) 1PCS Alex for first-lower handlebar φ17x323L 1PCS...

  • Page 5: Assembly Steps

    ASSEMBLY STEPS Assembly the rear & front stabilizer (J & J-4)and main frame with 4 STEP 1 washer ( P-13 ), 4 nuts ( P-12) and 4 bolts (P-14 ) STEP1 First, loosen the pre-assembled screws & cover. STEP 2 Connect the computer cable upper &...
  • Page 6 Slide the computer (A) down to the bracket situated at the top of hand post STEP 3 (B), and fix with two Fixing screws (A-1). Then plug the Upper Computer Wire (A-1) to the Computer as shown. Plug the pulse Computer Wires (A-2) into the side of the Computer (A).
  • Page 7 STEP 4 Assemble the Front post cover (Front & Rear) (M-3 & M-4) to the hand post using Screw (M5xP0.8x14L) ( D-2), Screw (M3*25) (P-5). Attach the Handlebar (B) to the Hand Post using the clamp (P-3), fix with two Flat Washers (φ7) (P-2), two Spring Washers (φ7) (P-4) and Screw (P-1).
  • Page 8 Fixing the two Lower handrail (E) to the Hand Post (D) with one Alex (M), STEP 5 two sets Waves washer φ 17.5xφ25x0.3t (P-8), Flat washer φ 10xφ26x2t (P-6) and Plastic washer φ 10xφ25x0.5t (P-21) and Bolt M8xP1.0x20L (P-7). E- R E- L 17.
  • Page 9 Attach the Left and Right lower handrail (E-L/R) to the Left and Right pedal STEP 6 tube (L & L-2) using tow Hexagon bolt (M8xP1.25x55L) (P-15), four flat washer ( φ 8) (P-16) and two Nylon nut (M8) (P-11). Then connect the crank connect (F-24) the Disc (F-21) (R/L) , Then connect the crank connation (F-24) the Pedal arm (L &...
  • Page 10 Attach the lower handrail (E) (L&R) to the left and right pedal arm (L & L- STEP 7 2),cover (M-8 & M-9) using screws (pt.Q12 & N14) . Assembly the right & left pedal ( M-13) onto the 2 pedal arm ( L &...
  • Page 11 Slide the upper hand post (C-3,C-2) (R/L) into the lower hand post (E) and STEP 8 then fix with the three carriage bolts (P-9) and washers (P-10) and Nylon nuts (P-11). STEP8...
  • Page 12 Assemble the Handrail cover (Rear & Front) (M-5 & M-6) to the lower handrail (L/R) STEP 9 using Screw (M3x25L) (P-5), Screw (M5xP0.8x14L) (E-6) and Screws. STEP9...

  • Page 13: Display Function

    Monitor manual instruction 【DISPLAY FUNCTION】 TIME : Count up - No preset target, TIME will count up from 00:00 to maximum 99:59 with each increment is 1 second. Count down - If training with preset Time, Time will count down from preset to 00:00.Each preset Increment or decrement is 1 minute between 1:00 to 99:00.

  • Page 14: Manual Mode

    Program selections are MANUAL, PROGRAM, H.R.C., USER, WATT. Press UP and DOWN to select the program you want and press START for QUICK START in Manual mode. MANUAL MODE After selecting MANUAL mode, press UP and DOWN button to increase and decrease level (from 1 to 16) and press MODE button to confirm.
  • Page 15 3. When computer just power on, it can not be touched or covered by any object or hand within 6 seconds. Attention! All preset data will be lost when unplug the power (adaptor) from the "Elliptical".

Table of Contents