Advertisement
Quick Links
Advertisement
Related Manuals for Casall INFINITY 1.2X
Summary of Contents for Casall INFINITY 1.2X
- Page 1 Casall INFINITY 1.2X CROSSTRAINER 93008...
- Page 2 Important: Please locate your serial number and record in the box below for service support purposes. Serial number here: ...
- Page 3 INFINITY 1.2X P-13 P-12 S c r e w M 3 * 1 4 L ( 2 ) Allen Bolt M7*P1.0*30L(2) A c o r n N u t f o r M 8 B o l t ( 2 ) C u r v e w a s h e r 1 7 .
- Page 4 INFINITY 1.2X P-16 B o x S p a n n e r ( 1 ) A l l e n K e y ( 2 ) P-17 P-19 Knob (foot pedal)M6*P1.0 (4) P-18 P i v o t T u b e ( 4 )
- Page 5 Assembly Diagram...
-
Page 6: Exploded Diagram
EXPLODED DIAGRAM... -
Page 7: Parts List
PARTS LIST Item spec. Q'ty A , A-1 Computer & Screw for computer 1SET Front handlebar Foam grip for front handlebar 2PCS End cap for foam grip φ7/8" 2PCS Hand pulse WP1007-33B 1SET Screw M3x20L 2 PCS Wire for hand pulse 1 PC Upper handlebar ( L) 1SET... - Page 8 L-1~L-11 Idler wheel set 1SET Front cover for computer Rear cover for computer Bottle holder Front cover (Left) for pedal post 2PCS Front cover (Right) for pedal post 2PCS Pedal (Left) M-7,M8 Left rear cover (upper/down) for pedal post 1SET Pedal (Right) M-10,M-11 Right rear cover (upper/down) for pedal post 1SET...
-
Page 9: Assembly Steps
ASSEMBLY STEPS STEP 1 Attach the Front Stabilizer (pt.J-1) to the Main Frame (pt.F-1) using two Allen bolt (pt.P-7) Attach the Rear Stabilizer (pt.K-1) to the Main Frame (pt.F-1) using two Allen bolt (pt.P-7). M8*16L STEP 2 1. Please remove four sets of the M8x16 Allen bolt (pt.D-5) and Flat Washer (pt.D-6)from the Main Frame (pt.F-1) 2. - Page 10 STEP 3 1. Attach the Front handlebar (pt.B-1) to the Handlebar post (pt.D-1) using the clamp cover (pt.P-3), and then fix with two Flat Washers (pt.P-2), two Spring Washers (pt.P-4), two Fixing Bolt (pt.P-1). 2. Pass the hand-pulse wire (pt.B-6) through the hole. 3.
- Page 11 STEP 4 1. Remove the pre-installed Screws (pt.D-3) on the handlebar post first. 2. Attach the Rear cover (pt.M-2) using two of Screws (pt.P-6) and one of Screws (pt.D-3) . 3. Attach the Front cover (pt.M-1) using Screws (pt.D-3) 4. Remove the pre-installed Screws (pt.D-7) on the handlebar post, and then assemble the Bottle holder (pt.M-3) by Screw (pt.
- Page 12 Fix the two Lower handlebar (pt.E-1) to the Handlebar Post (pt.D-1) with STEP 5 one Axle (pt.M-19), two sets of Wave washer (pt.P-13), Flat washers (pt.P- 12) and Gasket (pt.P-11) and Allen bolt (pt.P-10). Pay attention : Please use two allen key tools to fix bolt ( P-10 ) on both side at the same time.
- Page 13 STEP 6 1. Attach the Left and Right lower Handlebar (pt.E-1 L/R) to the Left and Right pedal post (pt.I-1 & I-3) using two Allen bolt (pt.P-14), four Flat washers (pt.P-15) and two Nylon nuts (pt.P-9). --- Figure A 2. Attach the Pedal post (pt.I-1 & I-3) onto the Crank connation set using one of Nylon nuts (pt.S-4), Flat washers (pt.S-3) and Plastic washers (pt.S-8).
- Page 14 STEP 7 1. Remove the pre-installed screws (pt.I-2) on the Pedal post first. 2. Attach the Lower handlebar (E-1 R/L) to the left and right pedal post (I-1), and then close the cover (M-4 & M-5) using screws (pt.P-5 & I-2). 3.
- Page 15 Slide the Upper handlebar post (C-1,C-4) (R/L) into the Lower handlebar (E-1) STEP 8 and then fix with the eight Allen bolts (P-8) M8*12L STEP 9 Connect the adaptor (N) to the DC hole (located on the back of the chain cover).
- Page 16 SM1705-67 INSTRUCTIONAL MANUAL For simple exercise, it is not always necessary to select a training program or manually set the TIME, DISTANCE or other values. You can simply start work out.
- Page 17 As soon as the computer is connected with power supply, an acoustic signal sounds and all of the displays are shown on LCD for 2 seconds, then showing wheel diameter. If no button are pressed and the pedals have not been moved for approx. 4 minutes, the computer will switch to power saving mode.
- Page 18 2 shot beeps =It is impossible to make any settings Training Data The computer calculates and displays all values automatically according to user exercising status (see table). Take note: * If only a “P” is shown instead of pulse value, it is impossible to measure the HR. Keep both hands holding on the handbar properly so that computer can detect your hear rate.
- Page 19 . DISTANCE . CALORIES . PULSE Use UP & DOWN to set values and confirm your selection by ENTER button. Press START/STOP button to start workout. As soon as one of the set values reach the preset Target, the computer will alarm with Bi-bi sound and stop.
- Page 20 . You should only graduate to Interval programs once you have exercised for several times. -Press START/STOP button to end exercising. All exercising value will remain. -Press RESET to reverse to workout selection menu. User-defined profile (USER PROGRAM) Here you can design your own profile with bars just like the preset program profiles. -Press UP &...
- Page 21 the computer automatically. -With the TARGET program, the preset value 100 will be shown. Press UP & DOWN buttons to set a value between 30~230 and confirm by ENTER. The program has been saved. -Set the desired session TIME with UP & DOWN buttons and press ENTER button to confirm. -Press STATR/STOP to start workout.
- Page 22 -If your heart rate is still very high after 60s (F is between 4 and 6), you could restart the recovery program to gradually slow your heart rate further. Trouble shooting: LCD displaying E-2: Check whether the 5PIN cable is not well connected to console or bad contact.