Table of Contents
Advertisement
Setting
PICTURE
BACKLIGHT*
1
Adjusts the overall image and background brightness. Press + or - to adjust.
NOTE: When MODE1 or MODE2 is selected in ROOM LIGHT SENSING, this function cannot be
changed.
CONTRAST*
1
Adjusts the image brightness in relationship to the input signal. Press + or - to adjust.
NOTE: When sRGB is selected in picture mode, this function cannot be changed.
1
SHARPNESS*
Adjusts the crispness of the image. Press + or - to adjust.
BRIGHTNESS*
1
Adjusts the image brightness in relationship to the background. Press + or - to adjust.
NOTE: When sRGB is selected in picture mode, this function cannot be changed.
COLOR TEMPERATURE*
1
Adjusts the color temperature of the entire screen. A low color temperature will make the screen
reddish. A high color temperature will make the screen bluish. If TEMPERATURE needs further
adjustment, the individual R/G/B/ levels of the white point can be adjusted. To adjust the R/G/B
levels, CUSTOM must be showing as the COLOR TEMP selection.
NOTE: When sRGB is selected in picture mode, predefi ned 6500k is set so it cannot be changed.
When PROGRAMMABLE1, PROGRAMMABLE2 or PROGRAMMABLE3 is selected in GAMMA
CORRECTION, this function cannot be changed.
COLOR CONTROL*
1
Adjusts the hue of the Red, Yellow, Green, Cyan, Blue and Magenta.
NOTE: When sRGB is selected in picture mode, this function cannot be changed.
1
GAMMA CORRECTION*
Select a display gamma for best picture quality.
NOTE: When sRGB is selected in picture mode, this function cannot be changed.
NATIVE
Gamma correction is handled by the LCD panel.
2.2
Typical display gamma for use with a computer.
2.4
Good for video (DVD, etc.)
S GAMMA
Special gamma for certain types of movies. Raises the dark parts and lowers the light parts of the
image (S-Curve).
DICOM SIM.
DICOM GSDF curve simulated for LCD type.
PROGRAMMABLE1, 2, 3 A programmable gamma curve can be loaded using NEC optional software.
UHD UPSCALING*
1
Achieves high-defi nition effect.
PICTURE MODE
Selects picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [CUSTOM1],
[CUSTOM2], [SVE-1 SETTINGS], [SVE-2 SETTINGS], [SVE-3 SETTINGS], [SVE-4 SETTINGS]
or [SVE-5 SETTINGS]. See page 19.
RESET
Resets the following settings within the PICTURE menu back to factory setting: BACKLIGHT,
CONTRAST, SHARPNESS, BRIGHTNESS, COLOR TEMPERATURE, COLOR CONTROL,
GAMMA CORRECTION, UHD UPSCALING.
ADJUST
ASPECT
Select the aspect ratio of the screen image.
NOTE: When the ASPECT is DYNAMIC or ZOOM, the image will be changed to FULL image
before POINT ZOOM, IMAGE FLIP, SCREEN SAVER, then start to POINT ZOOM, IMAGE FLIP,
SCREEN SAVER. After POINT ZOOM, IMAGE FLIP, SCREEN SAVER, ASPECT will be returned
to previous ASPECT. When ASPECT is changed during POINT ZOOM, IMAGE FLIP, SCREEN
SAVER, DYNAMIC and ZOOM will be FULL image.
When INPUT CONFIGURATION is active, ZOOM is not available. ZOOM is not available with
3840 x 2160 60 Hz signal.
NORMAL
Displays the aspect ratio the same as it is sent from the source.
FULL
Fills entire screen.
WIDE
Expands a 16:9 letter box signal to fi ll entire screen.
DYNAMIC
Expands a 4:3 pictures to fi ll the entire screen with non-linearity. Some of the outside image area
will be cut off due to expansion.
1:1
Displays the image in a 1 by 1 pixel format. (If the input resolution is higher than a 3840 x 2160
resolution, the image will be scaled down to fi t the screen).
If ROTATE of MULTI PICTURE CONTROL is selected, characters and lines may be displayed in
blurring, depending on the signal resolution.
*1: If SPECTRAVIEW ENGINE is ON, this function is grayed out.
*2: Depends on signal input.
English-23
Default
Depends on
destination
50
2
50*
50
10000K
0
2
NATIVE*
(except sRGB
setting)
OFF
Depends on
destination
-
FULL
-
-
-
-
-
Advertisement
Table of Contents
