Advertisement
Quick Links
Advertisement
Related Manuals for NEC MultiSync X551 UHD IGT
Summary of Contents for NEC MultiSync X551 UHD IGT
- Page 1 X551 UHD IGT with legs base X651 UHD-2 IGT with legs base User’s Manual © NEC Corporation 2016...
- Page 2 It can not be treated as a separate document. Please follow all warnings and precautions pointed in main manual provided with product. Table of contents Unpacking unit and fitting legs ............ 3 Connecting cables ..............12 Touch Screen Calibration ............12 © NEC Corporation 2016...
- Page 3 Due to mass of final product for installation and handling 4 people are required . Do not start unless you have enough people available , fitting with less people may result in injuries and damaged product. Product is provided in two boxes: © NEC Corporation 2016...
- Page 4 Unpack monitor from the box and put it flat on the floor with Cardboard still attached at the front of screen to cover it from scratches. NOTE : Do not remove Cardboard from the front of the screen. © NEC Corporation 2016...
- Page 5 Unpack legs and top plate from box. Prepare screws and key from accessory box. Make sure that anti shake washers are on bolts and M4/M8 screws. Put in X section of legs Screw in 8 screws in marked positions for each leg. © NEC Corporation 2016...
- Page 6 THE LEG BASE SHOULD BE SUPPORTED WHILST IT IS BEING ATTACHED TO THE IDIVIDUAL LEGS USING M8 BOLTS AND ANTI-SHAKE WASHERS (RACHET PROVIDED, 2X BOLTS 2X WASHERS PER LEG) Turn over leg base and attach top plate by screws provided in accessory box. © NEC Corporation 2016...
- Page 7 Unscrew and remove all the handles , table base will be fitted in their place. Remove all screws marked on above picture. NOTE: This action causes looseness of back plates. 4 people have to be presented during placing display on legs base. © NEC Corporation 2016...
- Page 8 There is a top and bottom side of legs base. © NEC Corporation 2016...
- Page 9 Remove styrofoam along with cardboard Remove foil from the touch screen before you connect cables. Now you can connect all cables. The touch screen is HID 'Plug and Play' with no driver required. © NEC Corporation 2016...
- Page 10 X551 UHD © NEC Corporation 2016...
- Page 11 X651 UHD-2 © NEC Corporation 2016...
-
Page 12: Connecting Cables
If the cursor fails to follow exact finger position, the screen can be re- calibrated in the following way: NOTE: Calibration under Windows is an option which can only make the touch screen work more accurate but it is not required. © NEC Corporation 2016... - Page 13 1. Open start menu in Windows and select Control Panel. 2. Open Hardware and Sound settings. © NEC Corporation 2016...
- Page 14 3. Open Tablet PC Settings 4. Press Calibrate button. © NEC Corporation 2016...
- Page 15 After touching the last cross, the calibration process ends. NOTE: If the touch is still not precise enough, the whole action can be repeated. © NEC Corporation 2016...
-
Page 16: Disposal Instruction
This includes monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your NEC display products, please follow the guidance of your local authority, or ask the shop where you purchased the product, or if applicable, follow any agreements made between yourself and NEC. - Page 17 NEC Display Solutions Europe GmbH Landshuter Allee 12-14 D – 80637 München Phone: +49 (0)89 99 699-0 Fax: +49 (0) 89 99 699-500 infomail@nec-displays.com www.nec-display-solutions.com © NEC Corporation 2016...
Need help?
Do you have a question about the MultiSync X551 UHD IGT and is the answer not in the manual?
Questions and answers