Daikin DV PTC 14 Series Installation Instructions Manual page 16

SPEED SELECTION DIP SWITCHES
COOL ADJUST
SELECTION SELECTION
SWITCHES SWITCHES
TAP S1 S2 S3
A OFF OFF OFF
B ON OFF ON
C OFF ON OFF
D ON ON ON
PROFILES PRE-RUN
A
B
C
D
TO SET AIRFLOW: (1) Select model and desired HIGH STAGE
COOLING AIRFLOW. Determine the corresponding TAP (A, B, C, D). Set
DIP switches S1 and S2 to the appropriate ON/OFF positions.
(2) Select model and installed electric heater size. Set DIP switches S9,
S10 and S11 to the appropriate ON/OFF positions.
(3) If airflow adjustment is required, set TRIM ENABLE SWITCH S8 to ON
(OFF-0% Trim) and set S3 and S4 to appropriate ON/OFF positions. TAP
A is +5%, TAP B is -5%, TAP C is +10%, TAP D is -10%.
TO SET COMFORT MODE: Select desired Comfort Mode Profile (see
profiles above). Set DIP switches S5 and S6 to appropriate ON/OFF
positions.
DEHUMIDIFICATION: To enable, set DIP switch S7 to ON. Cooling airflow
will be reduced to 85% of nominal value during cool call when DEHUM
command is present. To disable, set S7 to OFF.
CONTINUOUS FAN SPEED: Use DIP switches S12 and S13 to select
one of the 4 continuous fan speeds, TAP A is 25%, TAP B is 50%, TAP C
is 75%, TAP D is 100%.
NOTES:
1. Airflow data shown applies to legacy mode operation only. For a
fully communicating system, please see the outdoor unit's installation
instructions for cooling and heat pump airflow data. See Fully
Communicating Daikin System-Airflow Consideration section for details.
2. Airflow blink codes are approximations of actual airflow.
HTR
S9 S10 S11
DV25PTCB14 DV29PTCB14
(kW)
3 ON ON ON 550
5 ON ON OFF 650
6 ON OFF ON 700
8 ON OFF OFF 800
10 OFF ON ON 850
15 OFF ON OFF 875
19* OFF OFF ON NR
20 OFF OFF ON NR
21 OFF OFF OFF NR
25* OFF OFF OFF NR
Note : Airflow data shown applies to the electric heat only in either legacy mode or communicating mode operation
* Within thermostat user menu will display 20KW for OFF-OFF-ON dip switch selection, 21kW for OFF-OFF-OFF dip switch selection.
21kW for OFF -OFF-OFF dip switch selection.
NR - Not Rated
†† For match up with a 3 ton outdoor unit:
Airflow for 5kW up to 15kW heater kits shall be set to 1300 cfm speed tap of ON-OFF-ON.
††† For match up with a 3.5 ton outdoor unit: Heater kit application shall not exceed 20 kW.
Airflow for 5 kW up to 20 kW heater kits shall be set to 1620 cfm speed tap of ON-OFF-ON.
PROFILE
CONTINUOUS
SELECTION
FAN SPEED
SWITCHES
S4 S5 S6 S12
OFF OFF OFF OFF
OFF ON OFF ON
ON OFF ON OFF
ON ON ON ON
SHORT-RUN OFF DELAY
---- ---- 60 SEC. / 100%
---- 30 SEC. / 50% 60 SEC. / 100%
---- 7.5 MIN. / 82% 60 SEC. / 100%
---- 7.5 MIN. / 82% 30 SEC. / 50%
DV35PTCB14
DV33PTCC14 DV39PTCC14 DV49PTCC14 DV37PTCC14 DV59PTCC14 DV37PTCD14 DV59PTCD14 DV49PTCD14 DV61PTCD14 DV31PTCC14
DV37PTCB14
550 550 600
650 650 700
700 700 750
800 800 850
875 875 920
875 1050 950
NR NR NR
NR NR NR
NR NR NR
NR NR NR
S13
OFF
OFF
ON
ON
NOTE: Airflow blink codes are approximations of actual airflow. Airflows
provided are at 0.3 static.
NR NR NR
700 800 700
770 800 770
880 950 880
970 1090 970 1090
1090 1290 1090 1290
1280 1345 1280 1345
NR NR NR
NR NR NR
NR NR NR
16
COOLING / HEAT PUMP AIRFLOW TABLE
MODEL Tap Low Stage
A 410
DV25PTCB14 B 565
DV35PTCB14
C 650
D 685
A 375
DV29PTCB14 B 545
DV37PTCB14
C 630
D 740
A 475
B 565
DV33PTCC14
C 690
D 760
A 665
B 770
DV39PTCC14
C 815
D 910
A 710
B 745
DV49PTCC14
C 880
D 975
A 590
DV31PTCC14 B 705
DV37PTCC14
C 845
D 910
A 610
B 810
DV59PTCC14
C 940
D 1070
A 605
B 725
DV37PTCD14
C 820
D 940
A 1040
B 1260
DV59PTCD14
C 1330
D 1395
A 820
B 895
DV49PTCD14
C 995
D 1056
A 1080
B 1210
DV61PTCD14
C 1280
D 1350
NR NR NR
800 870 990
800 970 1110
950 1060 1200
1120 1240
1220 1520
NR NR
NR 1250 1520
NR NR NR
NR NR NR
High Stage
610
840
970
1020
610
795
930
1085
690
785
980
1110
990
1150
1095
1225
955
1005
1180
1310
880
1055
1265
1360
875
1225
1410
1595
900
1080
1225
1405
1445
1790
1890
1990
1195
1320
1460
1530
1630
1820
1925
2025
NR NR 600
950 1030 700
1060 1150 770
1150 1250 880
1220 1320 970
1520 1650 1090
NR NR 1280
NR 1690 NR
NR 1750 NR
NR 1750 NR