Kangaroo II Assembly Instructions Manual
Hide thumbs
Also See for Kangaroo II:
- Assembly instructions manual (15 pages) ,
- Assembly instructions manual (16 pages)
Related Manuals for Kangaroo Kangaroo II
Summary of Contents for Kangaroo Kangaroo II
- Page 1 ASSEMBLY INSTRUCTIONS Ka n g a ro o I I ITEM NO.: K8805 Teak K8811 Ash White SEW IN COMFORT. SEW LONGER.™...
-
Page 2: General A Ssembly Guidelines
Cleaning – To remove marks and enhance the surface, wipe with a gentle all-purpose cleanser. DO NOT use ammonia-based, harsh chemicals or abrasive cleaning agents. Wipe dry immediately. Electrical and Hydraulic Lifts – Require annual lubrication with WD-40 or similar lubricant. Kangaroo II Assembly Instructions... - Page 3 1 of 4 Right Leaf Support Panel 3 of 4 Drawer Bottom 1 of 4 Lift & Rails 4 of 4 Quilt Extension Panel 2 of 4 Platform 2 of 4 Support Panel 2 of 4 Kangaroo II Assembly Instructions...
-
Page 4: Par Ts List: Hardware
6x35 Cam Bolt 3.5x14 Screw Caster Knob 8x30 Dowel Pin 8x16 Fix Bolt ⁄ “ Cam Cover Butt Hinge Plate Caster Ball Catch Allen Wrench Magnet 14mm Wrench Threaded Dowel Pin Alignment Pin 4x20 Fix Bolt 3.5x35 Screw Kangaroo II Assembly Instructions... - Page 5 Par t 1: Cabinet Shell We can’t wait to get your brand new Kangaroo II Sewing Cabient up and running. Please contact our Customer Service Team at 1-800-533-7347, ext. 1 during normal business hours with any assembly related questions. 8x16 Fix Bolt x20...
- Page 6 6x35 Cam Bolt x2 8x30 Dowel Pin x12 Insert 12 d1 Dowel Pins into the edges of Panel D. Insert 4 d1 Dowel Pins into the edges of Panel X. Insert 2 c1 Cam Bolts into Panel X. Kangaroo II Assembly Instructions...
- Page 7 Insert 4 d1 Dowel Pins into the edges of Panel Y. Attach b3 Ball Catch with s1 Screws to front edge of Panel Y. Set aside the other parts of the ball catch to use later. Kangaroo II Assembly Instructions...
- Page 8 Attach Lift Rail (Left) to Panel Y with s1 Screws following predrilled holes. TIP: Spray a small amount of WD-40 or similar lubricant onto a paper towel and wipe the newly installed rails. This will make lift installation and operation easier. Kangaroo II Assembly Instructions...
- Page 9 Tighten cam locks and apply c2 Cam Covers. Make sure the casters are 180° locked and turn the cabi- net over onto its wheels. NOTE: You may need a friend to help you, but it is not required. Kangaroo II Assembly Instructions...
- Page 10 This illustration shows the back view of the Lift. Notice the wooden block and zip tie; the wooden block holds the piston in place so that the cables can be easily handled and inserted into the Lift Rails installed on your cabinet. Kangaroo II Assembly Instructions...
- Page 11 Cut the zip tie on the wooden block, but DO NOT remove the block yet. Lower the Lift to first lock position and remove the wooden block. DO NOT ADJUST LIFT POSITION until the top is installed, or you risk the Lift coming out and cables becoming disengaged. Kangaroo II Assembly Instructions...
- Page 12 Par t 2: Lift Panel Cable Plastic guides Lift rail Rail tabs Lift rail REMINDER: Our Customer Service Agents are ready to help if you run into trouble! Please call us at 1-800-533-7347, ext. 1 Kangaroo II Assembly Instructions...
- Page 13 “ Cam Cover x10 Insert c1 Cam Bolts into Panel A. 180° Lower Panel A, inserting cam bolts on Panel A onto cams on Panels X, D, Y and Z. Tighten cam locks and apply c2 Cam Covers. Kangaroo II Assembly Instructions...
- Page 14 Attach m Magnet Catch Plates to underside of Panels O1 and O2 using s2 Screws. Screw s4 Alignment Pins into the pre-drilled hole in the top of Panels O1 and O2. Screw t1 Casters into the bottom of Panels O1 and O2. Tighten with r3 Wrench. Kangaroo II Assembly Instructions...
- Page 15 Attach h2 Butt Hinges to Panels O3 and O4 using s1 Screws. Attach m Magnet Catch Plates to the underside of Panels O3 and O4 using s2 Screws. Screw s4 Alignment Pins into the pre-drilled hole in the top of Panels O3 and O4. Kangaroo II Assembly Instructions...
- Page 16 Par t 3: Top, Suppor t Leaf and Quilt Panel 3.5x14 Screw x24 Attach Panels O1 and O2 to Panel D using s1 Screws. Attach Panels O3 and O4 to Panel Z using s1 Screws. Kangaroo II Assembly Instructions...
- Page 17 Screws as shown. Attach h2 Butt Hinges to Panel A1 using s1 Screws as shown. Attach m Magnets using s1 Screws to Panel A5 as shown. Attach h2 Butt Hinges using s1 Screws to Panel A5 as shown. Kangaroo II Assembly Instructions...
- Page 18 Extend Gate Leg Panels O1 and O2. Balance Panel A1 on gate legs and attach h1 Hinges to Panel D using s1 Screws. Extend Support Panels O3 and O4. Balance Panel A5 on support panels and attach h1 Hinges to Panel Z using s1 Screws. Kangaroo II Assembly Instructions...
- Page 19 Attach m Magnet Catch Plate with s2 Screws. Attach h1 Knobs with b2 Fix Bolts. Attach remaining b3 Ball Catch parts with s1 Screws to Panel K. Set Panel K aside while you assemble the drawer. Kangaroo II Assembly Instructions...
- Page 20 L1 and L2. Tighten cams and apply c2 Cam Covers. Slide Panel L4 into grooves on Panels L, L1 and L2. Connect Panel L3 to Panels L1 and L2 using s3 Screws. Kangaroo II Assembly Instructions...
- Page 21 TIP: Gently open and close the drawers a few times to engage the Soft Close mechanism. Please do not place sewing machine or serger on A3 Support Panel. It is a cover panel only. Kangaroo II Assembly Instructions...
- Page 22 Completed Kangaroo II Cabinet Kangaroo II Assembly Instructions...
-
Page 23: Limited Lifetime Warranty
Kangaroo Sewing Furniture is designed for residential use only. ARROW SHALL HAVE NO LIABILITY for ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND and all such damages are EXCLUDED FROM THIS Warranty, such as loss of use, disassembly, transportation, labor, or damage to property on or near the product. - Page 24 Accessories to Complete Your Sewing Studio Custom Insert Arrow Sewing Chairs Enhance your sewing experience with a custom Arrow’s #1 Rated Height Adjustable Sewing Chair acrylic sewing insert! Custom acrylic sewing is a must have accessory for your dream sewing inserts are designed to fill the gap between your room! Cute, comfortable and convenient - our sewing machine and sewing cabinet’s lift opening...
Need help?
Do you have a question about the Kangaroo II and is the answer not in the manual?
Questions and answers