Lite teak electric/hydraulic lift, lite gray electric/hydraulic lift, lite ash white electric/hydraulic lift, teak electric/hydraulic lift, gray electric/hydraulic lift, ash white electric lift, lite ash white hydraulic lift (47 pages)
Summary of Contents for Kangaroo K8805
Page 1
ASSEMBLY INSTRUCTIONS Ka n g a ro o ITEM NO.: K8805 Teak K8807 Gray K8811 Ash White SEW IN COMFORT. SEW LONGER.™...
Cleaning – To remove marks and enhance the surface, wipe with a gentle all-purpose cleanser. DO NOT use ammonia-based, harsh chemicals or abrasive cleaning agents. Wipe dry immediately. Electrical and Hydraulic Lifts – Require annual lubrication with WD-40 or similar lubricant. Kangaroo Assembly Instructions...
Page 3
Right Drawer Side 1 of 3 Rear Right Leaf Support Panel 3 of 3 Drawer Back 1 of 3 Parts Box 1 of 3 Drawer Bottom 1 of 3 Quilt Extension Panel 2 of 3 Platform 2 of 3 Kangaroo Assembly Instructions...
Page 5
Par t 1: Cabinet Shell We can’t wait to get your brand new Kangaroo Sewing Cabient up and running. Please contact our Customer Service Team at 1-800-533-7347, ext. 1 during normal business hours with any assembly related questions. 8x16 Fix Bolt x20...
Page 6
6x35 Cam Bolt x2 8x30 Dowel Pin x16 Insert 12 d1 Dowel Pins into the edges of Panel D. Insert 4 d1 Dowel Pins into the edges of Panel X. Insert 2 c1 Cam Bolts into Panel X. Kangaroo Assembly Instructions...
Page 7
Insert 4 d1 Dowel Pins into the edges of Panel Y. Attach b3 Ball Catch with s1 Screws to front edge of Panel Y. Set aside the other parts of the ball catch to use later. Kangaroo Assembly Instructions...
Page 8
Attach Lift Rail (Left) to Panel Y with s1 Screws following predrilled holes. TIP: Spray a small amount of WD-40 or similar lubricant onto a paper towel and wipe the newly installed rails. This will make lift installation and operation easier. Kangaroo Assembly Instructions...
Page 9
Tighten cam locks and apply c2 Cam Covers. Make sure the casters are 180° locked and turn the cabi- net over onto its wheels. NOTE: You may need a friend to help you, but it is not required. Kangaroo Assembly Instructions...
Page 10
This illustration shows the back view of the Lift. Notice the wooden block and zip tie; the wooden block holds the piston in place so that the cables can be easily handled and inserted into the Lift Rails installed on your cabinet. Kangaroo Assembly Instructions...
Page 11
Cut the zip tie on the wooden block, but DO NOT remove the block yet. Lower the Lift to first lock position and remove the wooden block. DO NOT ADJUST LIFT POSITION until the top is installed, or you risk the Lift coming out and cables becoming disengaged. Kangaroo Assembly Instructions...
Page 12
Par t 2: Lift Panel Cable Plastic guides Lift rail Rail tabs Lift rail REMINDER: Our Customer Service Agents are ready to help if you run into trouble! Please call us at 1-800-533-7347, ext. 1 Kangaroo Assembly Instructions...
Page 13
“ Cam Cover x10 Insert c1 Cam Bolts into Panel A. 180° Lower Panel A, inserting cam bolts on Panel A onto cams on Panels X, D, Y and Z. Tighten cam locks and apply c2 Cam Covers. Kangaroo Assembly Instructions...
Page 14
Attach m Magnet Catch Plates to underside of Panels O1 and O2 using s2 Screws. Screw s4 Alignment Pins into the pre-drilled hole in the top of Panels O1 and O2. Screw t1 Casters into the bottom of Panels O1 and O2. Tighten with r3 Wrench. Kangaroo Assembly Instructions...
Page 15
Attach h2 Butt Hinges to Panels O3 and O4 using s1 Screws. Attach m Magnet Catch Plates to the underside of Panels O3 and O4 using s2 Screws. Screw s4 Alignment Pins into the pre-drilled hole in the top of Panels O3 and O4. Kangaroo Assembly Instructions...
Page 16
Par t 3: Top, Suppor t Leaf and Quilt Panel 3.5x14 Screw x24 Attach Panels O1 and O2 to Panel D using s1 Screws. Attach Panels O3 and O4 to Panel Z using s1 Screws. Kangaroo Assembly Instructions...
Page 17
Screws as shown. Attach h2 Butt Hinges to Panel A1 using s1 Screws as shown. Attach m Magnets using s1 Screws to Panel A5 as shown. Attach h2 Butt Hinges using s1 Screws to Panel A5 as shown. Kangaroo Assembly Instructions...
Page 18
Extend Gate Leg Panels O1 and O2. Balance Panel A1 on gate legs and attach h1 Hinges to Panel A (top) using s1 Screws. Extend Support Panels O3 and O4. Balance Panel A5 on support panels and attach h1 Hinges to Panel A (top) using s1 Screws. Kangaroo Assembly Instructions...
Page 19
Attach c1 Cam Bolts to Panel L. Attach m Magnet Catch Plate with s2 Screws. Attach h1 Knobs with b2 Fix Bolts. Attach remaining b3 Ball Catch parts with s1 Screws to Panel K. Set Panel K aside while you assemble the drawer. Kangaroo Assembly Instructions...
Page 20
Panels as shown here. L1 and L2. Tighten cams and apply c2 Cam Covers. Slide Panel L4 into grooves on Panels L, L1 and L2. Connect Panel L3 to Panels L1 and L2 using s3 Screws. Kangaroo Assembly Instructions...
Page 21
Soft Close mechanism. Threaded Dowel Pin x3 Magnet x1 3.5x14 Screw x2 Screw p1 Threaded Dowel Pins into Panel A3 as shown above. Using s1 Screws, attach m Magnet to Panel A3 as illustrated. Kangaroo Assembly Instructions...
Page 22
Par t 4: Drawer Unit and Front Panel Slide Panel A3 into place, inserting threaded dowel pins into pre- drilled holes and clicking magnet into place. Please do not place sewing machine or serger on A3 Support Panel. It is a cover panel only. Kangaroo Assembly Instructions...
Kangaroo Sewing Furniture is designed for residential use only. ARROW SHALL HAVE NO LIABILITY for ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND and all such damages are EXCLUDED FROM THIS Warranty, such as loss of use, disassembly, transportation, labor, or damage to property on or near the product.
Page 25
Accessories to Complete Your Sewing Studio Custom Insert Arrow Sewing Chairs Enhance your sewing experience with a custom Arrow’s #1 Rated Height Adjustable Sewing Chair acrylic sewing insert! Custom acrylic sewing is a must have accessory for your dream sewing inserts are designed to fill the gap between your room! Cute, comfortable and convenient - our sewing machine and sewing cabinet’s lift opening...
Need help?
Do you have a question about the K8805 and is the answer not in the manual?
Questions and answers