Related Manuals for Kangaroo K8805EL
Summary of Contents for Kangaroo K8805EL
- Page 1 ASSEMBLY INSTRUCTIONS Kan g aro o ITEM NO.: K8805 Hydraulic Lift Teak K8807 Hydraulic Lift Gray K8811 Hydraulic Lift Ash White K8805EL Electric Lift Teak K8807EL Electric Lift Gray K8811EL Electric Lift Ash White OLL24J001 SEW IN COMFORT. SEW LONGER.™...
- Page 2 Cleaning – To remove marks and enhance the surface, wipe with a gentle all-purpose cleanser. DO NOT use ammonia-based, harsh chemicals or abrasive cleaning agents. Wipe dry immediately. Electrical and Hydraulic Lifts – Require annual lubrication with WD-40 or similar lubricant. Kangaroo Assembly Instructions...
- Page 3 3 of 3 Left Gate Leg 1 of 3 Rear Right Leaf Support Panel 1 of 3 Drawer Bottom 1 of 3 Back Panel 2 of 3 Quilt Leaf 2 of 3 Drawer Front 2 of 3 Kangaroo Assembly Instructions...
- Page 4 3.5x14 Screw x110 3.5x35 Screw x4 Threaded Dowel Pin x3 3x14 Screw Allen Wrench x1 14mm Wrench x1 Knob x2 Butt Hinge x14 Magnet x5 Caster x2 Plate Caster x5 Pre-installed parts Caster Bracket Drawer Runners Ball Catch x2 Kangaroo Assembly Instructions...
- Page 5 Clips Transformer Box NOTE: Lift, Power Converter, Transformer Box and Programmable Controller arrive fully hooked up. You will need to disconnect all cords in order to install, and then re-engage cord connections once lift installation is complete. Kangaroo Assembly Instructions...
- Page 6 Part 1: Cabinet Shell We can’t wait to get your brand new Kangaroo Sewing Cabient up and running. Please contact our Customer Service Team at 1-800-533-7347, ext. 1 during normal business hours with any assembly related questions. 8x16 Fix Bolt x20...
- Page 7 Insert 12 d1 Dowel Pins into the edges of Panel D. Attach 2 c1 Cam Bolts to Panel D. Insert 4 d1 Dowel Pins into the edges of Panel X. Insert 2 c1 Cam Bolts into Panel X. Kangaroo Assembly Instructions...
- Page 8 Insert 4 d1 Dowel Pins into the edges of Panel Y. Attach b3 Ball Catch with s1 Screws to front edge of Panel Y. Set aside the other parts of the ball catch to use later. Kangaroo Assembly Instructions...
- Page 9 Attach Lift Rail (Left) to Panel Y with s1 Screws following predrilled holes. TIP: Spray a small amount of WD-40 or similar lubricant onto a paper towel and wipe the newly installed rails. This will make lift installation and operation easier. Kangaroo Assembly Instructions...
- Page 10 (Panel G). Insert c1 Cam Bolts on Panels X and Z into cams on Panel D. Tighten cams and apply c2 Cam Covers. Kangaroo Assembly Instructions...
- Page 11 Tighten cam locks and apply c2 Cam Covers. 180° Make sure the casters are locked and turn the cabinet over onto its wheels. NOTE: You may need a friend to help you, but it is not required. Kangaroo Assembly Instructions...
- Page 12 Part 2: Lift Installation Hydraulic Lift Installation: Page 13 Electric Lift Installation: Page 15 Kangaroo Assembly Instructions...
- Page 13 Lift Rails installed on your cabinet. Do not pull on the red ribbon or remove the zip ties just yet! Attach the Lift to Panel A2 using s1 Screws. Lift x1 Screw Kangaroo Assembly Instructions...
- Page 14 DO NOT ADJUST LIFT POSITION until the top is installed, or you risk the Lift coming out and cables becoming disengaged. Cable Plastic guides Lift rail Rail tabs Lift rail Turn to Page 17 to continue cabinet assembly. Kangaroo Assembly Instructions...
- Page 15 Part 2b: Electric Lift Installation NOTE: This illustration depicts the BACK of your lift. Pulley 3 Cable Plastic Glides Motor Pulley 2 Power Cords Pulley 1 Cable Attach the Lift to Panel A2 using s1 Screws. Screw Kangaroo Assembly Instructions...
- Page 16 Do you have questions? Email us anytime at cs@arrowsewing.com or give Arrow Sewing Customer Service a call for assistance at 1-800-533-7347, ext. 1 during normal business hours. Turn to Page 17 to continue cabinet assembly. Instructions for Electric Lift cord management and operation begin on Page 27. Kangaroo Assembly Instructions...
- Page 17 Part 3: Top, Support Leaf and Quilt Panel 6x35 Cam Bolt x10 ⁄ “ Cam Cover x10 180° Lower Panel A, inserting cam bolts on Panel A onto cams on Panels X, D, Y and Z. Tighten cam locks and apply c2 Cam Covers. Kangaroo Assembly Instructions...
- Page 18 Attach m Magnet Catch Plates to underside of Panels O1 and O2 using s2 Screws. Screw s4 Alignment Pins into the pre-drilled hole in the top of Panels O1 and O2. Screw t1 Casters into the bottom of Panels O1 and O2. Tighten with r3 Wrench. Kangaroo Assembly Instructions...
- Page 19 Attach h2 Butt Hinges to Panels O3 and O4 using s1 Screws. Attach m Magnet Catch Plates to the underside of Panels O3 and O4 using s2 Screws. Screw s4 Alignment Pins into the pre-drilled hole in the top of Panels O3 and O4. Kangaroo Assembly Instructions...
- Page 20 Part 3: Top, Support Leaf and Quilt Panel 3.5x14 Screw x24 Attach Panels O1 and O2 to Panel D using s1 Screws. Attach Panels O3 and O4 to Panel Z using s1 Screws. Kangaroo Assembly Instructions...
- Page 21 Screws as shown. Attach h2 Butt Hinges to Panel A1 using s1 Screws as shown. Attach m Magnets using s1 Screws to Panel A5 as shown. Attach h2 Butt Hinges using s1 Screws to Panel A5 as shown. Kangaroo Assembly Instructions...
- Page 22 Extend Gate Leg Panels O1 and O2. Balance Panel A1 on gate legs and attach h1 Hinges to Panel A (top) using s1 Screws. Extend Support Panels O3 and O4. Balance Panel A5 on support panels and attach h1 Hinges to Panel A (top) using s1 Screws. Kangaroo Assembly Instructions...
- Page 23 Attach c1 Cam Bolts to Panel L. Attach m Magnet Catch Plate with s2 Screws. Attach h1 Knobs with b2 Fix Bolts. Attach remaining b3 Ball Catch parts with s1 Screws to Panel K. Set Panel K aside while you assemble the drawer. Kangaroo Assembly Instructions...
- Page 24 Panels as shown here. L1 and L2. Tighten cams and apply c2 Cam Covers. Slide Panel L4 into grooves on Panels L, L1 and L2. Connect Panel L3 to Panels L1 and L2 using s3 Screws. Kangaroo Assembly Instructions...
- Page 25 Soft Close mechanism. Threaded Dowel Pin x3 Magnet x1 3.5x14 Screw x2 Screw p1 Threaded Dowel Pins into Panel A3 as shown above. Using s1 Screws, attach m Magnet to Panel A3 as illustrated. Kangaroo Assembly Instructions...
- Page 26 Part 4: Drawer Unit and Front Panel Slide Panel A3 into place, inserting threaded dowel pins into pre- drilled holes and clicking magnet into place. Please do not place sewing machine or serger on A3 Support Panel. It is a cover panel only. Kangaroo Assembly Instructions...
- Page 27 The Programmable Controller is attached to the inside of the cabinet using 3 screws. You may choose to use an electric screwdriver for this step. Make sure the torque is set below 5 to avoid damaging your cabinet’s finish. Kangaroo Assembly Instructions...
- Page 28 Controller through the Cord Port and plug them in to the Power Converter. NOTE: Each cord and cord receptacle has a different pin pattern, making it easy to match the cords to the Power Converter. Programmable Controller Cord Lift Cords Power Converter Transformer Box Kangaroo Assembly Instructions...
- Page 29 NOTE: Use your preset functions your own way! You can set may place that over your sewing well and use your cabinet as a Flatbed Position for multiple machines or preset positions for desk. Storage or Free Arm positions. The choice is yours! Kangaroo Assembly Instructions...
- Page 30 Say goodbye to hunched shoulders, tired wrists, and an aching back and hello to HAPPY SEWING! To place an order for your own Custom Acrylic Insert, visit us online at ArrowSewing.com, or contact Arrow Sewing Customer Service at 1-800-533-7347 ext 1 during normal business hours. Kangaroo Assembly Instructions...
- Page 31 Completed Kangaroo Cabinet Kangaroo Assembly Instructions...
- Page 32 Kangaroo Sewing Furniture is designed for residential use only. ARROW SHALL HAVE NO LIABILITY for ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND and all such damages are EXCLUDED FROM THIS Warranty, such as loss of use, disassembly, transportation, labor, or damage to property on or near the product.
- Page 33 Accessories to Complete Your Sewing Studio Custom Insert Arrow Sewing Chairs Enhance your sewing experience with a custom Arrow’s #1 Rated Height Adjustable Sewing Chair acrylic sewing insert! Custom acrylic sewing is a must have accessory for your dream sewing inserts are designed to fill the gap between your room! Cute, comfortable and convenient - our sewing machine and sewing cabinet’s lift opening...
Need help?
Do you have a question about the K8805EL and is the answer not in the manual?
Questions and answers