Viewfinder Normal Indications - Sony DXC-D35H/D35PH Operating Instructions Manual

Viewfinder Normal Indications

Only when connecting the DSR-1/1P
Meaning
Indication
50P CONNECT Connection with the PRO 50-pin
connector on the DSR-1/1P.
(Freeze mix function is disabled.)
MP TAPE An incorrect type of cassette has
been loaded. (The cassette is
automatically ejected and the
indication disappears in about two
seconds.)
CLIP DATA ERR Abnormality of the cassette memory
data.
AUDIO 48kHz? At back space editing, audio
(4 flashes/s) recording mode has changed from
32 kHz mode (4-channel mode) to
48 kHz mode (2-channel mode).
AUDIO 32kHz? At back space editing, audio
(4 flashes/s) recording mode has changed from
48 kHz mode (2-channel mode) to
32 kHz mode (4-channel mode).
ERROR:91-13F Failure in loading or saving the
cassette memory data.
When other error indication
appears, refer to the operating
instructions for the DSR-1/1P.
Asking whether you will continue
CLIP CONT?
shooting in ClipLink mode or not
when the cassette contains ClipLink
data. (The indication disappears
when you press the ClipLink
CONTINUE button on the DSR-1/
1P or start the next shooting without
pressing it.)
CLIP NEAR END At back space editing in ClipLink
mode, capacity for only 1 to 3 index
pictures remains.
CLIP END Impossible to record any more clip
shots.
qf White balance indication
The following indications appear.
Indication Meaning
EZ Operating in EZ mode (The ATW function is
selected.)
ATW The ATW function is selected. (The ATW
button was pressed and the indicator is lit.)
W:A White balance memory A is selected.
W:B White balance memory B is selected.
W:P Preset white balance is selected.
W:M Manual adjustment is performed remotely.
qg SKIN DTL indication
This appears when the skin detail function is activated
(The SKIN DTL switch is set ON.)
56
Chapter 4 Viewfinder Screen Indications and Menus
qh EVS indication
This appears when the EVS (Enhanced Vertical
definition System) function is enabled. (See page 84.)
qj Lens f-stop indication
This shows the f-stop of the lens.
Note
Depending on the lens being used, this indication may
differ slightly from the actual f-stop on the lens.
qk Gain indication
This shows the gain value, and the settings of the
HYPER GAIN switch and the DPR (Dual Pixel
Readout) function (see page 64) as shown in the
following table.
Example indication Meaning
18dB Gain setting is 18 dB.
DPR 18dB The DPR function is enabled.
In this case the DPR function
approximately doubles the gain (an
increase of 6 dB) over the current
gain setting (in this case 18 dB).
HYPER The HYPER GAIN switch is in the
ON position.
In this case the hyper gain function
increases the gain by a factor of
about 60 or 120 with respect to 0
dB regardless of the current gain
setting (that is, increased to 36 or
42 dB).
ql Filter setting indication
This shows the setting of the FILTER control.
Indication Filter setting
3200 1 (3200K)
56ND 2 (5600K +
5600 3 (5600K)
56ND 4 (5600K +
w; Clock indication
The clock indication is shown in one of the following
ways (according to the CLOCK IND setting of CAM,
BARS, or OFF in advanced menu page 8).
CAM: Always displayed.
BARS: Displayed whenever color bars are
displayed.
OFF: Not displayed.
If the clock indication is displayed during recording, it
is recorded onto the image.
1
/ ND)
8
1
/ ND)
64