Table of Contents
Advertisement
Viewfinder Normal Indications
During normal operation, the following items can be
indicated in the viewfinder.
1 VTR operation status indication
2 TAKE/CUE indication
a)
3 Recording time or time data
indication
a), b), c)
4 NG indication
a)
5 Clip mode indication
a)
6 Clip remaining
indication
a)
7 Status display area
8 EZ FOCUS indication
9 LOW LIGHT indication
c)
0 Camera microphone output
c)
indication
!¡ Audio recording level indicators
!™ Tape remaining indication
The significance of each of the indications shown in
the figure is as follows.
1 VTR operation status indication
This indicates the VTR's current operation status
(REC, PLAY, etc.).
2 TAKE/CUE indication
This displays a TAKE or CUE indicator when using
the ClipLink function and recording with the DSR-1/
1P.
TAKE: When recording in Mark mode, this
indication appears when a Mark IN point is set
and disappears when the next Mark OUT point is
set.
CUE: When recording in CUE mode, this indication
appears for about 1 second when a cue point is set.
3 Recording time or time data indication
This shows the following values.
• When the REC TIME switch on the camera is in the
TTL position: The total recording time
• When the REC TIME switch on the camera is in the
DUR position: The duration of the current recording
cut
a), b)
R E C
T A P E N E A R E N D
T C G
1
2 : 3 4 5 6 :
N G
A
U
T
O B L C
M
- K -
1 8
9
E
Z
F O U
C
S
:
L
O
W
G T
H
S
S
:
1 / 0 0
1
0
3 - 5
0
2
a), b), c)
a), b), c)
:
0 0
E Z
A
K
A
T W
E V S
O
1
R
N D
9
4
0 8
2
4
2 2 4 M
:
P
E
R
R O : S
R
D
P
a) Displayed only when a DSR-1/1P is connected.
b) Displayed only when a PVV-3/3P is connected.
c) Whether or not to display can be selected by menu setting.
d) This is recorded over the picture being shot.
• With a VTR connected, when the REC TIME switch
on the camera head is in the OFF position and the
item TC IND in advanced menu page 6 is set to
"ON": A time data value from the VTR depending on
the DISPLAY switch settings on the VTR as shown
in the following table
DISPLAY switch
setting
COUNTER
TC
U-BIT
When using the DSR-1/1P, time data values appear
during playback, fast forward, rewind, or recording
review.
4 NG indication
An "NG" (No Good) indicator appears if you
designate a recorded scene as "NG" when using the
ClipLink function and recording with the DSR-1/1P.
Chapter 4 Viewfinder Screen Indications and Menus
!£ VTR warning indication
!¢ EZ mode indication
!∞ ATW indication
!§ EVS indication
!¶ Lens f-stop indication
!• Gain indication
c)
!ª Filter setting indication
@º Clock indication
a), b), c), d)
@¡ Voltage/error indication
@™ Shutter setting indication
Time data displayed
CNT: Tape transport time
TCG: a time code from the time code
generator
TCR: a time code from the time code
reader
UBG: a user bit value from the user
bit generator
a), b)
c)
c)
c)
47
Advertisement
Table of Contents
