Sony DXC-D35H/D35PH Operating Instructions Manual page 65

Advanced menu page 3
a) For DXC-D35P/D35WSPL: EBU75
Item
AWB MEM
Selects whether or not to
make the FILTER knob
settings (1 to 4) correspond
to separate white balance
adjustment values stored in
memory.
TONE
Selects whether or not to
output a 1-kHz audio signal
with the color bars when the
OUTPUT/DL/DCC+ has
been set to BARS.
BARS
Selects normal width or
narrower width for color
bars.
REMOTE1
Sets a function for position 1
of a switch connected to the
REMOTE1 connector.
REMOTE2
Sets a function for position 2
of a switch connected to the
REMOTE1 connector.
BAUD RATE
Sets a baud rate for a
computer connected to the
REMOTE connector 2 (to be
supported in future version).
a)
Settings
2 (normal value): No
correspondence with FILTER
knob settings. Only two
adjustment values (A and B)
are stored in memory.
2 4FL: Correspondence
with FILTER knob settings.
Each of the four knob
settings can be used to set A
and B adjustment values, for
a total of eight settings.
ON (normal value): Output
audio signal.
OFF: Do not output audio
signal.
SMPTE (normal value for
DXC-D35/D35WSL):
Normal width
EBU75 (normal value for
DXC-D35P/D35WSPL): EBU
75%
EBU100 (for DXC-D35P/
D35WSPL): EBU 100%
SPLIT (for DXC-D35P/
D35WSPL): Not for normal
operation
SNG: Narrower than normal
(used for satellite
communications, etc.)
REC (normal value):
Specifies recording start/stop
MARK: Specifies a Mark IN/
OUT point.
CUE: Specifies a cue point.
NG: Specifies NG/OK.
REC: Specifies recording
start/stop.
MARK (normal value):
Specifies a Mark IN/OUT
point.
CUE: Specifies a cue point
NG: Specifies NG/OK.
9600, 38400 (normal value)
Advanced menu page 4
cPAGE4 (NEXTcV PREVcv)
MARKER : CENT/90%
LIMITS : OFF
ZEBRA : 1
ZEBRA1 : 70IRE
VF S DTL:
VF TALLY:
VF PLAY : Y
LENS SEL: 1
EXIT MENU (YEScv)
a) For DXC-D35P/D35WSPL: 70%
Item
MARKER
Selects ON/OFF setting for
center marker, size setting
(percentage of viewfinder
screen area), and display
ON/OFF setting.
LIMITS (For DXC-D35WSL/
D35WSPL)
Selects the safety zone size
when the scan size is 16:9.
ZEBRA
Selects type of zebra pattern
display.
ZEBRA1
Sets base level for zebra
pattern 1.
VF S DTL
Sets the detail level of
images on the viewfinder
screen (displayed only when
a viewfinder other than the
DXF-701/701CE/701WS/
701WSCE/801/801CE is
attached).
Chapter 4 Viewfinder Screen Indications and Menus
a)
0
2
Settings
CENT/90% (normal value):
Displays center marker and
safety zone marker at 90%
size.
CENT/80%: Displays center
marker and safety zone
marker at 80% size.
90%: Displays only safety
zone marker at 90% size.
80%: Displays only safety
zone marker at 80% size.
CENT: Displays only center
marker.
OFF (normal
value):FDepends on the
scan size.
4:3, 13:9, 14:9, 15:9
1 (normal value): Displays
the zebra pattern over parts
having a video level.
between 70 and 90 IRE (or
70 and 90%).
Use the next item (ZEBRA1)
to select the base level.
2: Displays the zebra pattern
over parts having video
levels of 100 IRE or above
( or 100% or above).
1/2: Dual display (both 1
and 2)
70 IRE (normal value) to 90
IRE or 70% (normal value)
to 90%
Can be set for each IRE
step or 1% step.
–99 to ±0 (normal value) to
+99
Negative values set softer
edges and positive values
set sharper edges.
(continued)
65