Table of Contents
Advertisement
MM
YY
Note : The internal clock can also be adjusted in maintenance mode.
Example: On 30 June 2012 at 17:15 enter:
4 17 15 30 06 12
After the control panel is powered up, the clock is set to 00 00 01 01 00.
12.47. Editing keypad text
The names of devices and programmable outputs as displayed
on the keypad unit can be edited as follows:
• Pressing and holding the
editing mode and the name of the device enrolled to address
01 is then displayed with a flashing cursor on the first text
character.
• Key functions:
and
1 and 7 character-selection
(A,B,C,D.......8,9,0)
4 and 5 cursor control (left/right)
2
# # # #
List of editable text:
text
Description
Names of devices in addresses 01 to 50
01: to 50: Devices
Control panel
Name of control panel (e.g. displayed if its cover
is opened)
Keypad
Name of hard-wired keypad
Name of the communicator in the control panel
Communicator
Name of the master code
Master code
Names of user codes
01: to 50: Code
Names of ARC code
ARC Code
Service code
Name of the service code
Names of programmable outputs
PGX and PGY
OASIS JA-80
The default text displayed in operating mode if
no other text needs to be displayed. If erased
then nothing will be displayed.
Notes:
• Only capital letters can be entered.
• The length of text is limited to the length of the display.
• The text is only stored in the keypad used for editing (different
keypads in the system can show different text if desired).
• Text is stored in the non-volatile memory of keypads, so power
disconnection will not erase any stored text.
• Convenient text editing is possible using a PC running Comlink
software.
• Besides device names, keypads also use so-called internal text such
as "service", "maintenance mode" etc, and this text can also be edited
via Comlink software by selecting "Settings" on the menu and then
"keypad text".
• After editing keypad text using Comlink software, all keypads
(including wireless ones) must be connected to the digital bus to save
the changes to the keypad units by clicking on the OK button in the
software.
Factory default setting: in addresses 01 to 50 there is the text
"Device".
Other
default
"Communicator", "Master code", users 01 to 50 "Code","ARC
Code", "Service code", "PGX", "PGY" and "OASIS JA-80".
13. Operating the system
The Oasis system can be operated locally using a keypad or
a keyfob and it can also be operated remotely by mobile phone
or the Internet (if equipped with a suitable communicator).
Installation manual: Oasis security system JA-80K
is the month (01 to 12)
is the year (00 to 99)
?
key (in service mode) enters text
text scrolling (see table)
delete selected character
exit editing (& save changes)
text:
"Control
panel",
13.1.
The system keypad
Indoor keypads model JA-80F (wireless) or JA-80E (wired) can
be used to operate and program the system. Both keypad types
provide the same functionality:
13.1.1. Keypad indicators:
ABC setting (arming) status of sections – if all sections are
set then all these indicators (A B & C) are lit.
flashing = alarm, with the simultaneous display of alarm
details on the LCD, e.g.:
constantly lit = fault – details are displayed by pressing
the "?" key
power. Constantly lit = mains ok. Flashing = no mains,
control panel powered by back-up battery only.
13.1.2. LCD display
st
The 1
line displays the status: triggered detector, Service
mode etc. In standby mode, it shows the text "OASIS JA-80"
(editable, see 12.47).
nd
The 2
line displays the name of a device.(e.g. 01: Main Door
etc.). The text can be edited, see 12.47.
Displaying the status of detectors and programmable
outputs: Details on permanently triggered detectors (e.g. open
windows) and the status of the PGX and PGY outputs can be
displayed by pressing the ? key.
13.1.3. Keypad display sleep-mode
In operating mode, the wireless keypad unit displays the
system status for 20 seconds (if battery-powered) after the last
interaction with a user, and then goes into sleep mode. Pressing
any key, triggering the keypad input or opening the keypad's flip
cover re-activates the display.
"Keypad",
13.1.4. Keys
0–9
digital code entry
∗ ∗ ∗ ∗
function sequences
#
escape
ABC hot key for setting the entire system (all sections A, B &
C)
A
hot key for setting section A (e.g. afternoon partial setting
of the garage)
- 18 -
Alarm
03: Kitchen
MKE55800
Advertisement
Table of Contents
