jablotron Oasis User Manual
Gsm house alarm
Hide thumbs
Also See for Oasis:
- Installation manual (22 pages) ,
- Instruction manual (21 pages) ,
- Quick start manual (2 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for jablotron Oasis
Summary of Contents for jablotron Oasis
- Page 2 ∗ Programming sequences beginning with the ∗1 sets the entire system (the same as the ABC key) ∗2 sets section A (the same as the A key) ∗3 sets A and B, or just B (the same as the B key) ∗4 event memory recall (key 4 scrolls backwards) –...
- Page 3 Limited warranty Subject to the conditions of this Limited warranty Jablotron Ltd. warrants this product to be free from defects in design, material and workmanship at the time of its original purchase by a customer for a subsequent period of two (2) years.
-
Page 5: Table Of Contents
Contents Dear Oasis user ....................2 What is a security system? ................2 System access codes (cards) ................3 System setting (arming) ................4 During the setting (arming) process … ........... 5 After the system has just been set (armed) ..........6 System unsetting (disarming) .............. -
Page 6: Dear Oasis User
Dear Oasis user The development and production of your security system have been done by the manufacturer with maximum care so that your oasis of safety – your room, house or company premises – can be protected as well as possible. -
Page 7: System Access Codes (Cards)
The Oasis system is configurable and its exact behaviour is determined by system settings. The following text contains references to the system configuration table which is to be found at the end of this manual. The table should be filled in by an installer during the installation process. -
Page 8: System Setting (Arming)
A, B, or ABC key must always be followed by entering an access code (or by presenting an access card). • Key-fob: press for total setting (A + B + C) press to set section A press to set sections A+B Oasis user manual MKE22102... -
Page 9: During The Setting (Arming) Process
If you wish to accept/confirm the bypass suggestion, press *. If no confirmation is made, the system will not be set! The system behaves the same way when bypassing has been pre-programmed in maintenance mode. Oasis user manual MKE22102... -
Page 10: After The System Has Just Been Set (Armed)
If final-door detector mode ( 12.) is active and you came in through the corresponding door, then the entrance delay would be six times longer than if it had been triggered by an ordinary detector (i.e. if you Oasis user manual MKE22102... -
Page 11: To Stop The Alarm
4. Keep in mind that there could be somebody hidden on the premises. If you have any doubts, then it is recommended to have the premises checked by a security service from the alarm receiving station. Oasis user manual MKE22102... -
Page 12: Operating The System From An Outdoor Keypad
8. Controlling connected devices from a keypad The control panel allows you to control various devices in the building, e.g. heating, air conditioners, ... ( 13.) and ( 14.). Control can be performed via a keypad by keying-in the following: Oasis user manual MKE22102... -
Page 13: Remote Control - By Phone, Internet
# key. A sequence is stored into control panel memory only after the sequence has been completely entered. Note: The Oasis JA-80 system has three modes: operating mode, maintenance mode and service mode. Operating mode is for the day-to-day... -
Page 14: Programming The Master Code (Card)
Code programming is only possible when the system is unset (disarmed) and not in maintenance mode. In practice, it is convenient that each user has his own user code pre- programmed. The system stores to its memory which code was used for what Oasis user manual MKE22102... - Page 15 To erase a code without knowing its nn position use sequence master code (card) 00 code ∗ • To erase all codes and cards set 6 master code (card) 00 0000. The master code (card) will not be effected. Oasis user manual MKE22102...
-
Page 16: Key-Fob Setting
We recommend triggering the detectors (zones) one by one and verifying that the triggering is indicated on the keypad display – by displaying the signal type and source. Remote controllers (key-fobs) or panic buttons can be tested in a similar way. Oasis user manual MKE22102... -
Page 17: Displaying Which User/Card Positions Are Occupied
B indicator shows whether a card is programmed or not. (This means if both indicators are lit, the position is occupied by a code and a card.) • To exit this code/card display mode press the # key. Notes: Oasis user manual MKE22102... -
Page 18: Bypassing
The control panel has a built in real-time clock which is used to time-stamp all recorded events in the control panel memory. The clock should be set during installation. However, the administrator can re-set the clock. This can be used Oasis user manual MKE22102... -
Page 19: Automatic Setting/Unsetting Schedule
Set all Set all Set all Unset all Unset all Unset all Set all Set A Set A Set all Set AB Set B Unset all Unset all Unset A Unset all Unset all Unset B Oasis user manual MKE22102... -
Page 20: Programming Phone Numbers For Sms Messages
This setting is usually performed by an installer during the installation. The programming of the phone numbers can be also done by the administrator in Maintenance mode if enabled ( Follow the manual supplied with the B.). communicator. Oasis user manual MKE22102... - Page 21 • Use the Code holder column to write down the name of the person who is authorized to use the code • Use positions 41-50 for codes/cards whose operations should not be reported by SMS messages. Oasis user manual MKE22102...
- Page 22 Oasis configuration table Oasis control panel configuration 1. An unsplit system (only ABC) 2. A system with partial setting (arming) (A or AB or ABC) 3. A split system (A or B or ABC) 4.
- Page 23 Use the Location/User column to describe where a detector is located (a porch, living room,…) or to write down the user of a remote controller (Uncle Charles, Aunt Mary). • The table can be also printed out in the Olink software. Oasis user manual MKE22102...