Advertisement
Installing the Cellular Cradle Plus
(Included in some kits)
For best mounting results and long-
term performance, we suggest that
you choose a flat smooth surface
like the console area of your vehicle
between the two front seats. If this is
not available in your vehicle, you may
mount the cradle on the front of the
dashboard.
If mounting the cradle on a sloped
area of the dashboard in your vehicle,
please note that gravity may affect
the adhesive over time. Use the
screw mount for a more permanent
attachment.
Attaching the Cradle
Once you have installed the mount in the desired location, attach the cradle by aligning
the rectangular hole on its back with the hook on the mount. Grasping the sides of the
cradle, slide it downward approximately ¼ inch into place.
5
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
Or email: tech@wilsonelectronics.com
In-Vehicle
Option 1 - Adhesive Bracket
Clean the area where the bracket will be
mounted with the alcohol wipe (included in
some kits) and a soft cloth. Allow to dry.
Peel the backing to expose the adhesive
and press the bracket onto the desired
location in the vehicle. Note: Be sure the
bracket is positioned vertically.
Allow the adhesive to cure for 24 hours
before you attach the cradle.
Note: Once the cradle is attached, you can
adjust the angle of the adhesive bracket
by applying gentle pressure to the top or
bottom of the cradle.
Option 2 - Adhesive/Screw Swivel
Bracket
Clean the area where the bracket is to be
mounted with the alcohol wipe (included in
some kits) and a soft cloth. Allow to dry.
For an adhesive mount, peel the backing
to expose the adhesive and press the
bracket onto the desired location in the
vehicle. Allow the adhesive to cure for
24 hours before you attach the cradle.
For a screw mount, use an ice pick or awl
to punch through the adhesive and expose
the four screw holes in the bracket. Note:
Screws are not included in this kit.
Using the bracket as a template, mark the
locations for the screws as shown, drill
pilot holes and attach the bracket with
screws (not included).
Once the cradle is attached, you can
loosen the knurled wheel and swivel the
hook to the desired angle, then re-tighten
the wheel.
Hours: 7am to 6pm MST.
Installing the Ultra Slim Antenna
(Included in some kits)
Cellular data card
For cell phones with an internal antenna,
place the Ultra Slim on the back of the
phone near the top. (Figure 1)
Note: Certain phones, such as the
Motorola RAZR, have internal antennas at
the base, rather than the top, in which case
the Ultra Slim should be attached at the
bottom rear of the phone.
For cell phones with an external antenna,
place the Ultra Slim directly below the
phone's original antenna. (Figure 2)
If you have any questions as to the location
of the antenna on your phone, call Wilson
Electronics Technical Support at:
866-294-1660.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
Or email: tech@wilsonelectronics.com
In-Vehicle
The Ultra Slim must be placed directly
on the cell phone or cellular data card to
work properly. Attach the Ultra Slim to the
cell phone or cellular data card with the
VELCRO
provided.
®
The Ultra Slim cable is long enough to
reach the Signal Booster location. This
allows for ease and convenience of use.
To adjust the Ultra Slim for the best signal,
go to a weak signal location where your cell
phone registers only 1-2 bars without the
Ultra Slim connected. (Be sure the Signal
Booster is turned off when checking for low
signal). Then, attach the Ultra Slim to the
phone, power up the Signal Booster and
you should see a signal improvement of 2 or
more bars.
Note: Many phones take up to 30 seconds
to reset the bar indicator.
To maximize performance, attach the Ultra
Slim as close as possible to the original
antenna on your cell phone or cellular data
card.
Figure 1
Figure 2
To Signal Booster
6
Hours: 7am to 6pm MST.
Advertisement
