Installing a Wilson Electronics Outside Antenna ..4 Installing a Wilson Electronics Inside Antenna ..5 Installing a Wilson Electronics Signal Booster..6 Powering Up a Wilson Electronics Signal Booster .
Signal Booster Soft Cases (859909) Omni-Directional Antenna (301201) K Marine Antenna (301130) Appearance of device and accessories may vary. Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.
Before Getting Started This guide will help you properly install Wilson Electronics In-Building Wireless Smart Technology™ Signal Boosters. It is important to read through all of the installation steps for your particular application prior to installing any equipment. Read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment.
Signal Booster and then into a AC power strip (power supply sold separately in 801175). See page 7 for more information. Wilson Electronics recommends that all AC power supplies for home electronics be plugged into a AC Power Strip with at least a 1000 Joule rating.
800-204-4104 (part #859902). Signal Booster Surge Protector Power Strip recommended for all AC power supplies Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.
12 of this installation guide. Follow the specific antenna installation instructions included with the Inside Antenna. Wilson Electronics has several Inside Antenna options. The dome and Panel Antennas are the most popular for in-building applications. For a square room, a Dome Antenna will provide better coverage. (A) For a rectangular room, a Panel Antenna will provide better coverage.
Connect the Outside Antenna to the Signal Booster with Wilson 400 low loss cable (available from Wilson Electronics). Place the Inside Antenna in the center of the area needing the amplified signal. It is important to have at least 50 feet of separation between...
Warning: Verify that both the Outside Antenna and the Inside Antenna are connected to the Signal Booster before powering up the Signal Booster. NOTE: The aluminum casing of a Wilson Electronics Signal Booster will adjust very quickly to the ambient temperature of its environment. For example, in the summer, when the attic of a house can easily exceed 140 degrees Fahrenheit, the Signal Booster temperature may be 10 or more degrees higher.
40 50 60 down to prevent a receive overload. Try moving the Outside Antenna farther away from the cell tower. Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.
Page 10
45 55 65 down to prevent a receive overload. Try moving the Outside Antenna farther away from the cell tower. Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.
Antenna slightly away from the cell tower. The Signal Booster will reset automatically but may also be reset by disconnecting and reconnecting the power supply. Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.
You will also experience some signal loss from cables, splitters and taps used to connect your system (see the table on page 13). Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.
Formula: -90 + 60 + 16 + -7 + 0 + 0 = -21 With a signal strength of -21, coverage distance would be approximately 120 feet from the Inside Antenna. Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660 or email: tech@wilsonelectronics.com. Hours: 7 am to 6 pm MST.
Returned Material Authorization (RMA) number supplied by Wilson Electronics. Wilson Electronics shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of the repaired or replaced product back to the original consumer within the continental United States.
Page 16
In-Building Wireless Signal Booster Specifications (GSM & Cellular) Model/Part Cellular Cellular Cellular Cellular Cellular Number # 801105/801175 # 801106 #801108 #801110 #801165 Frequency Uplink 824-849 824-849 824-835 835-849 824-849 Downlink 869-894 869-894 869-880 880-894 869-894 Channel A Channel B Gain...