Page 1
Video Intercom Face Recognition Door Station User Manual...
Page 2
WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,...
Page 3
Video Intercom Face Recognition Door Station User Manual CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY...
Page 4
Video Intercom Face Recognition Door Station User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a hazardous situation which, if not avoided, will or Danger could result in death or serious injury. Indicates a potentially hazardous situation which, if not Caution avoided, could result in equipment damage, data loss,...
Page 5
Video Intercom Face Recognition Door Station User Manual Safety Instruction Warning • All the electronic operation should be strictly compliance with the electrical safety regulations, fire prevention regulations and other related regulations in your local region. • Please use the power adapter, which is provided by normal company. The power consumption cannot be less than the required value.
Page 6
Video Intercom Face Recognition Door Station User Manual • Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover. •...
Page 7
Video Intercom Face Recognition Door Station User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Page 8
Video Intercom Face Recognition Door Station User Manual ce matériel est conforme aux limites de dose d'exposition aux rayonnements, FCC / CNR-102 énoncée dans un autre environnement.cette eqipment devrait être installé et exploité avec distance minimale de 20 entre le radiateur et votre corps. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE"...
Page 9
Video Intercom Face Recognition Door Station User Manual Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes : l'appareil ne doit pas produire de brouillage, et l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Video Intercom Face Recognition Door Station User Manual Contents 1 Appearance ....................1 2 Terminal and Wiring Description ..............3 2.1 Terminal Description ..................3 2.2 Wiring Description .................... 4 2.2.1 Door Lock Wiring ..................5 2.2.2 Door Contact Wiring ................. 5 2.2.3 External Card Reader Wiring ..............
Page 11
Video Intercom Face Recognition Door Station User Manual 5.1.6 Volume Adjustment ................18 5.1.7 Search Version ..................19 5.2 Video Intercom Operation ................19 5.2.1 Call Resident ................... 19 5.2.2 Call Center ....................19 5.3 Unlock Door ....................20 5.3.1 Unlock by Password ................20 5.3.2 Unlock by Presenting Card ..............
Page 12
Video Intercom Face Recognition Door Station User Manual 6.5.2 Modify and Delete Organization ............. 40 6.6 Person Management ..................40 6.6.1 Add Person ..................... 41 6.6.2 Modify and Delete Person ..............42 6.6.3 Import and Export Person Information ..........42 6.6.4 Get Person Information from Device ............
Video Intercom Face Recognition Door Station User Manual 1 Appearance Note The appearance of the device vary according to different model. Refers to actual device. With Fingerprint Module Figure 1-1 Front and Side Panel Table 1-1 Appearance and Description Description Light Camera Microphone...
Page 14
Video Intercom Face Recognition Door Station User Manual With Card Reader Module Figure 1-2 Front and Side Panel Table 1-2 Appearance and Description Description Light Camera Microphone Screen Card Reader Area TAMPER...
Video Intercom Face Recognition Door Station User Manual 2 Terminal and Wiring Description 2.1 Terminal Description Figure 2-1 Terminal Description Table 2-1 Description of Terminal and Interface Name Interface Description Power Input DC 12 V 12 VDC Power Input ALARM OUT AO1+ Alarm Relay Output 1 AO1-...
Video Intercom Face Recognition Door Station User Manual 2.2.1 Door Lock Wiring Figure 2-2 Door Lock Wiring Note Terminal NC1/COM1 is set as default for accessing electric strike. Terminal NO1/ COM1 is set as default for accessing magnetic lock/electric bolt. 2.2.2 Door Contact Wiring Figure 2-3 Door Contact Wiring...
Video Intercom Face Recognition Door Station User Manual 2.2.3 External Card Reader Wiring Note • Please set the DIP switch first before connecting the card reader. • If the DIP switch should be configured when the card reader is power-on, please reboot the card reader after configuring the DIP switch.
Page 19
Video Intercom Face Recognition Door Station User Manual RS-485 Card Reader Wiring Figure 2-4 RS-485 Card Reader Wiring...
Video Intercom Face Recognition Door Station User Manual Wiegand Card Reader Wiring Figure 2-5 Wiegand Card Reader Wiring 2.2.4 Alarm Device Input Wiring...
Video Intercom Face Recognition Door Station User Manual Figure 2-6 Alarm Device Input Wiring 2.2.5 Alarm Device Output Wiring Figure 2-7 Alarm Device Output Wiring...
Video Intercom Face Recognition Door Station User Manual 3 Installation Note • Make sure the device in the package is in good condition and all the assembly parts are included. • The power supply the door station supports is 12 VDC. Please make sure your power supply matches your door station.
Video Intercom Face Recognition Door Station User Manual Note • Ask our technique supports and sales and purchase the DS-KABD9613-G junction box. • The dimension of the junction box is: 406.7 mm(W) × 174.8 mm(H) × 44 mm(D). • The installation hole should be larger than junction box. The suggested dimension of the installation hole is 407.5mm(W) ×...
Video Intercom Face Recognition Door Station User Manual 4 Activation 4.1 Activate Device Locally You are required to activate the device first by settings a strong password for it before you can use the device. Steps 1. Power on the device to enter the activation page automatically. 2.
Video Intercom Face Recognition Door Station User Manual Note • The password required 8 to 16 characters. • The way to enter the password, take button 2 as an example: Press 2 to enter the number '2' or hold 2 for 1.5 s and press 2 again to enter the character 'a'.
Page 26
Video Intercom Face Recognition Door Station User Manual Note • When the device is not activated, the basic operation and remote operation of device cannot be performed. • You can hold the Ctrl or Shift key to select multiple devices in the online devices, and click the Activate button to activate devices in batch.
Video Intercom Face Recognition Door Station User Manual 5 Local Operation 5.1 Local Configuration 5.1.1 Network Settings Set the network parameters of the door station and linked devices. Steps 1. Tap Call/Open to enter the calling page. 2. Enter #777, and tap unlock button to pop up the dialog box. 3.
Video Intercom Face Recognition Door Station User Manual Note • The No. of the main door station is 0. • The No. of the sub door stations should be set from 1 to 99. • Every unit should have at least one main door station. •...
Video Intercom Face Recognition Door Station User Manual 1) Tap Card. 2) Tap + to issue card. 3) Set the card No. and swiping the card. 4. Add faces. 1) Tap Face. 2) Face at the camera and tap Capture. 3) Tap Save.
Video Intercom Face Recognition Door Station User Manual 5.1.5 Change Password Enter the context of your task here (optional). Steps 1. Tap Call/Open to enter the calling page. 2. Enter #777, and tap unlock button. 3. Enter the admin password and tap OK to enter the settings page. Note By default, the admin password is 888999.
Video Intercom Face Recognition Door Station User Manual 6. Tap < to save the settings. 5.1.7 Search Version Steps 1. Tap Call/Open to enter the calling page. 2. Enter #777, and tap unlock button. 3. Enter the admin password and tap OK to enter the settings page. Note By default, the admin password is 888999.
Video Intercom Face Recognition Door Station User Manual 5.3 Unlock Door 5.3.1 Unlock by Password Unlock by Common Password Tap Call/Open to enter the calling page. Enter 【 # + Room No. + Common Password】, and tap unlock button. Note The default common password is 123456.
Video Intercom Face Recognition Door Station User Manual Note • Make sure you have added the fingerprint to the device. • Fingerprint function may vary with different modules. Please refer to the actual devices. Put your finger on the finger recognition module to unlock. 5.3.4 Unlock by Face Note Make sure you have added your face picture to the device.
Video Intercom Face Recognition Door Station User Manual 6 Configuration via Client Software 6.1 Edit Network Parameters To operate and configure the device via LAN (Local Area Network), you need connect the device in the same subnet with your PC. You can edit network parameters via iVMS-4200 client software.
Video Intercom Face Recognition Door Station User Manual Figure 6-1 Add to the Client 6.2.2 Add Device by IP Address Steps 1. Click +Add to pop up the adding devices dialog box. 2. Select IP/Domain as Adding Mode. 3. Enter corresponding information. 4.
Video Intercom Face Recognition Door Station User Manual You can add many devices at once whose IP addresses are among the IP segment. Steps 1. Click +Add to pop up the dialog box. 2. Select IP Segment as Adding Mode. 3.
Page 37
Video Intercom Face Recognition Door Station User Manual Figure 6-3 General Time Click Time to enter the device time settings page. Figure 6-4 Synchronize Time Select Time Zone or Enable NTP. Click Save to save the time settings. • Time Zone •...
Page 38
Video Intercom Face Recognition Door Station User Manual • Check the checkbox of Enable NTP to enable NTP. • Enter the server address, NTP port, and synchronization interval. • DST • Check the checkbox of Enable DST to enable DST. •...
Page 39
Video Intercom Face Recognition Door Station User Manual Note • Click Restore Default Settings, all default settings, excluding network parameters, will be restored. • Click Restore All, all default settings, including network parameters, will be restored. The device will be reset to inactivated status.
Page 40
Video Intercom Face Recognition Door Station User Manual Figure 6-6 User Page Note • The new password and confirm password should be identical. • After editing the password of device, click refresh button from the device list, the added device will not be there. You should add the device again with new password to operate the remote configuration.
Video Intercom Face Recognition Door Station User Manual Figure 6-7 RS-485 Settings Note For indoor station and main station, there are 3 choices for the working mode: transparent channel, disable, and custom. 6.3.2 Video Intercom Click Video Intercom to enter the Video Intercom Settings page. Device ID Configuration Steps 1.
Page 42
Video Intercom Face Recognition Door Station User Manual Note The device type select Door Station as default. You can select Outer Door Station to change the device type. 3. Click Save to enable the device number configuration. Note • For main door station, the serial No. is 0. •...
Page 43
Video Intercom Face Recognition Door Station User Manual Steps 1. Click Permission Password to enter the settings page. 2. Select Type of the password. 3. Edit the password. 4. Click Save to enable the settings. Access Control and Elevator Before You Start •...
Page 44
Video Intercom Face Recognition Door Station User Manual Figure 6-10 Access Control and Elevator 2. Set the Access Control parameters. 1) Select the door No. 2) Set the Door-unlocked Duration. 3) Optional: Enable Upload Alarm for Not-Closed Door. 4) Click Save to enable the settings.
Page 45
Video Intercom Face Recognition Door Station User Manual Note • The door-unlocked duration ranges from 1 s to 255 s. • If you check Upload Alarm for Not-Closed Door, an alarm will be triggered automatically if the door is not locked in the configured duration. •...
Page 46
Video Intercom Face Recognition Door Station User Manual Note • For door station, there are 4 I/O input terminals. By default, Terminal 1 and 2 correspond to Door Status. Terminal 3 and 4 correspond to interfaces of Door Switch. • For door station, there are 2 I/O Output Terminals.
Video Intercom Face Recognition Door Station User Manual Note • Up to 5 pictures can be added. Picture formats requires JPG. The size of the pictures should be less than 1MB. The switching duration of the picture ranges from 1 to 10 seconds. Refers to the Appendix C for the details. •...
Page 48
Video Intercom Face Recognition Door Station User Manual Before You Start On the linked devices network configuration page, you can configure the network parameters of main stations, SIP servers and management centers of the same LAN. The devices can be linked to the door station and realize the linkage between these devices.
Page 49
Video Intercom Face Recognition Door Station User Manual Figure 6-13 FTP Settings 2. Enable Enable Main FTP. 3. Select IP address from the drop-down list of server mode. 4. Enter the FTP server address, and port No. 5. Optional: Enable the anonymity. 6.
Video Intercom Face Recognition Door Station User Manual Steps 1. Click Advanced Settings to enter the advanced network settings page. Figure 6-14 Advanced Settings 2. Enter the DNS server addresses. 3. Click Save to enable the settings. 6.3.4 Video Display Settings Click Video Display to enter the Video Display Settings page.
Video Intercom Face Recognition Door Station User Manual 2. Select the Camera No. 3. Select the video standard (PAL and NTSC can be selected). 4. Optional: Enable WDR mode. 5. Set the Brightness, Contrast, Saturation and Sharpness of the video. 6.
Video Intercom Face Recognition Door Station User Manual After running the iVMS-4200, video intercom devices should be added to the client software for remote configuration and management. 6.5 Organization Management On the main page of the Client Software, click PersonalManagement to enter the configuration page.
Video Intercom Face Recognition Door Station User Manual After adding the organization, you can add person to the organization and manage the added person such as issuing cards in batch, importing and exporting person's information in batch, etc. Note • Up to 2,000 persons can be added.
Video Intercom Face Recognition Door Station User Manual 3) Select Normal Card as Card Type. 4) Enter the Card No. 5) Click Read and the card(s) will be issued to the person. 4. Link the device to the person. 1) Set the linked devices. Linked Device You can bind the indoor station to the person.
Video Intercom Face Recognition Door Station User Manual 3) Check the checkboxes to select the person information to export. 4) Click OK to start exporting. 2. Importing Person: You can import the Excel file with persons information in batch from the local PC. 1) Click Import Person.
Video Intercom Face Recognition Door Station User Manual 6.6.5 Change Person to Other Organization You can move the person to another organization if needed. Steps 1. Select the person in the list and click Change Organization. 2. Select the organization to move the person to. 3.
Page 57
Video Intercom Face Recognition Door Station User Manual Figure 6-17 Issue Card in Batch 2. Click Settings.
Video Intercom Face Recognition Door Station User Manual Figure 6-18 Card Settings 3. Select Card Type and Card No. Type. 4. Click OK to save the settings. Result After issuing the card to the person, the person and card information will display in the Person(s) with Card Issued list.
Video Intercom Face Recognition Door Station User Manual 2) Select the Template of the schedule. 3) Check the person to Selected according to your needs. 4) Check the device to Selected according to your needs. 4. Click Save. 5. Check the permission and click Apply All to Device. The status of the permission displays as Applied.
Video Intercom Face Recognition Door Station User Manual • Click to adjust the volume of the loudspeaker. • Click to adjust the volume of the microphone. • Click Hang Up to hang up the dialog. • Click to open the door remotely. Note •...
Video Intercom Face Recognition Door Station User Manual 4. Edit the Subject, Type and Information. 5. Click View to select the picture. 6. Click Send. Note • Up to 63 characters are allowed in the Subject field. • Up to 6 pictures in the JPGE format can be added to one notice. And the maximum size of one picture is 512KB.
Page 62
Video Intercom Face Recognition Door Station User Manual Click ˅ to unfold the drop-down list and select the device type as Indoor Station, Door Station, Outer Door Station or Analog Indoor Station. Or select All Devices to search logs with all device types. Start Time/End Time Click the time icon to specify the start time and end time of a time period to search the logs.