HIKVISION UD06519B-A Quick Start Manual

Fingerprint Time Attendance Terminal
Quick Start Guide
UD06519B-A
©2017 Hangzhou Hikvision Digital Technology Co., Ltd.
It includes instructions on how to use the Product. The software embodied
in the Product is governed by the user license agreement covering that
Product.
About this Manual
This Manual is subject to domestic and international copyright protection.
Hangzhou Hikvision Digital Technology Co., Ltd. ("Hikvision") reserves all
rights to this manual. This manual cannot be reproduced, changed,
translated, or distributed, partially or wholly, by any means, without the
prior written permission of Hikvision.
Trademarks
and other Hikvision marks are the property of Hikvision and
are registered trademarks or the subject of applications for the same by
Hikvision and/or its affiliates. Other trademarks mentioned in this manual
are the properties of their respective owners. No right of license is given to
use such trademarks without express permission.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT
DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS
PROVIDED "AS IS", WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES
NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR
PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE
TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR
DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT,
EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF
PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT
TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY
LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER
ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;
HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF
REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT
LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO
ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION
SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH
ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE
APPLICABLE LAW, THE LATER PREVAILS.
1
Appearance
2.8-inch
LCD Display Screen
Front View
ESC OK
2 3
1
ABC DEF
Keypad
4 5 6
GHI JKL MNO
7 8 9
PQRS TUV WXYZ
12V Power Interface USB Interface
Bottom View
Ethernet Port
2
Installation
Hole 1
Paste the template on the required place,. Drill screw and cable
holes according to the template.
Hole 1: Wall Mounting Screw Hole
Method 1:
Wall Mounting
102010858
1. Drill holes on the wall or other places
according to the mounting template. (Supplied)
Note: The length and width will be 2 to 3 mm
smaller than the actual device's.
Method 2:
Wall Mounting
with
Mounting Plate
Clockwise Rotation
1. Remove the two screws at the
bottom of the front cover and
remove the back cover.
Loudspeaker
Front Cover
Exiting Key
ESC
Direction
Keys
1
Fingerprint
4
Reading Module
GHI
Numeric Keys/
7
Letter Keys
EN PQRS
0
Notes: 1. If the device model contains "-B", long press the deleing key for 2s to enter the powering off interface.
Tap OK to power off.
2. Long press Key 6 for 3s to enter One-Touch Wi-Fi Settings mode. You can set Wi-Fi parameters for the
device via the App on the phone. Press Key 6 again to exit the mode.
(The model with "-1" does not support One-Touch Wi-Fi Settings mode.)
Hole 1
Mounting Template
UP
Hole 1
165.0 mm
2. Insert the screw sockets of the setscrews in the drilled
holes.
3. Fix and fasten the screws in the sockets on the wall or
other places. (You should reserve 5.2mm to 5.5 mm for
the hanging the device when fix and fasten the screws.)
140
Clockwise Rotation
2. Align the back cover on the level on the
wall or other places.
3. Drill through the holes at the four
corners of the back cover.
4. Insert the screw sockets of the setscrews
in the drilled holes.
Keypad Descriptions
OK Key
OK Key: Press to confirm operations. Press and hold the
key for 3s to login the main interface.
Deleting Key: 1.Press to delete the letters or numbers one
OK
by one in the textbox;
2.Long-press to clear all contents in the textbox.
Deleting
2 3
Key
ABC DEF
5 6 EN
JKL MNO
8 9
0
TUV WXYZ
Editing Key: Press to enter the editing status. Shift among
Editing Key
numbers/lowercases, numbers/uppercases and symbols.
There are two kinds of editing key icons:
4. Align the three holes on the device plate
with the fixed screws and hang the device
on the wall.
5. Fasten the screws in the 6. Align the front cover to the back
sockets to fix the back cover on cover and buckle them together.
the wall or other places. 7. Fasten the screws at the bottom
of the front cover.
or .
EN
Anticlockwise Rotation
Anticlockwise Rotation