Rigid Pipe Venting Horizontal Or Vertical Terminations - Regency Fireplace Products P42 Owners & Installation Manual

INSTALLATION
The Rigid Pipe Venting System offers a complete line of component parts for installation of both horizontal and vertical installations. Many items are
offered in decorative black, as well as galvanized finish. We recommend using the galvanized finish for installation with the P42.
The minimum components required for a basic
horizontal termination are:
1 Horizontal Termination Cap
1 90 o Elbow
1 Flue Adaptor
1 Wall Thimble
1 Length of pipe to suit wall thickness
(see chart)
Vertical
Terminal
Storm Collar
Part # 953
f i r e - p a r t s . c o m
Flashing
943 or 943S
Ceiling Firestop
(Part # 963)
Pipe Length
When using piping other than Simpson
Dura-Vent, 3 screws must be used to
secure rigid pipe to adaptor.
The FPI AstroCap TM and FPI Riser Vent terminal is certified for installations using FPI venting systems as well as Simpson Dura-Vent®, Direct Vent
GS, American Metal Products, Ameri Vent Direct vent and Selkirk Direct-Temp. FPI
Fireplace Products International Ltd. Dura-Vent® and Direct Vent GS are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.
12
RIGID PIPE VENTING
Horizontal or Vertical Terminations
Wall thickness is measured from the back
standoffs to the inside mounting surface of
termination cap. For siding other than vinyl
furring strips may be used, instead of the vinyl
siding standoff, to create a level surface to
mount the vent terminal. The Terminal must not
be recessed into siding. Measure the wall
thickness including furring strips.
If a Vinyl Siding Standoff is required (it must be
used with vinyl siding), measure to outside
surface of wall without siding and add 2 inches.
Vinyl Siding
Standoff (Optional)
Part #950
Adj.Pipe Length
11" - 14-5/8"
o
90 Elbow
24" Pipe
Length
Rigid Pipe Adaptor
(Part# 510-994)
Horizontal
Termination
Cap
Wall Thimble
Part # 942
Flat Wall Installation
Wall Thickness
(inches) Required (inches)
4" - 5-1/2"
7" - 8-1/2"
10" - 11-1/2"
9" - 14-1/2" 11" - 14-5/8" Adj. Pipe
15" - 23-1/2"
Corner Installation
Wall Thickness
(inches) Required (inches)
3-1/4" - 6-3/4" 11" - 14-5/8" Adj. Pipe
7-3/4" - 16-1/4"
7-1/4" - 8-3/4"
4-1/4" - 5-3/4"
TM
, and FPI AstroCap
Regency P42-2 Zero Clearance Direct Vent Gas Fireplace
Alternate
Horizontal
Termination
Caps
WARNING:
Do not combine venting components from
different venting systems.
However use of the the AstroCap
Riser is acceptable with all systems.
This product has been evaluated by Intertek for
using a Dura-Vent Flue Adaptor in conjunction
with Selkirk Direct-Temp and Ameri Vent Direct
venting systems. Use of these systems with
the Direct Vent GS starting collar is deemed
acceptable and does not affect the Intertek WHI
listing of components.
Vent Length
6"
9"
12"
17" - 24" Adj. Pipe
Vent Length
17" - 24" Adj. Pipe
6" + 12"
9" + 9"
6" + 9"
TM
are the proprietary trademarks of FPI
TM and FPI