Checking Accumulator Status; Electronic Safeguards; Maintenance And Service; Accessories - Narex ASR 600-3SB BASIC Original Operating Manual

English
Attention!
If you wish to change the position of the shift button, first check
that the switch button is released�
Note:
You may hear a loud click when you first use the device after
changing the rotation direction� This is normal and does not indi-
cate a problem�
Work mode set-up
Selecting the operating mode (output) of choice can only be made
if an LED on the operating mode selection panel (5) is lit up� If
no LED on the operating mode selection panel (5) is lit up, first,
press and release the switch (3), and then select your operating
mode (output) of choice by repeatedly pressing the operating
mode selection button (5a) on the operating mode selection pan-
el (5)� Setup options for individual operating modes and overview
of LED indication on the operating mode selection panel (5) is de-
scribed below:
Operating mode 1
Right green LED lit�
Suitable for tightening and loosening screw joints in the M8 to M12
range�
Maximum tightening torque: up to 150 Nm
Operating mode 2
Middle green LED lit�
Suitable for tightening and loosening screw joints in the M10 to
M16 range�
Maximum tightening torque: up to 250 Nm
Operating mode 3
Left green LED lit�
Suitable for tightening and loosening screw joints in the M12 to
M24 range�
Maximum tightening torque: up to 540 Nm
Note:
The work mode LED indicator (5b) will automatically shut off
about 1 minute after the work is finished.
Tool fastening
When mounting tools, always make sure that these attachments
are mounted on a ½" spindle (6) or to a transfer adapter all the
way (14)�
Mounting a belt clip
Place the machine on a horizontal surface (e�g� a working table)�
Slide the bent end of the belt clip (11) into the base for the belt
clip (13)� Secure the belt clip (11) using a fastening screw (12) and
a corresponding screwdriver� You can mount the belt clip to the
machine from the right, as well as the left side� Be careful not to
mount the belt clip the wrong way round� The belt clip position
must correspond to the illustration�
22

Checking Accumulator Status

The machine is fitted with an accumulator status control panel (8)�
Press the control button (8a) on the accumulator status panel (8)�
An accumulator status indicator (8b) will light up based on the
state of charge (capacity) of the accumulator�
Overview of accumulator's state of charge (capacity) indication:
Number of fully lit LEDs
3
2
1

Electronic Safeguards

The machine is fitted with electronics designed to prevent serious
damage to the machine�
If the electronic safeguards detect any of the listed faults/defects,
the machine stops immediately and a red LED will start flashing
on the operating mode selection panel (5)� Proceed in accordance
with the table to remove the fault/defect�
Overview of safety features and methods for returning the machine to operation:
Defect
Protection against over-dis-
charging of the accumulator
Overload protection
Protection against overheating Wait until the machine cools
Short-circuit protection

Maintenance and service

Instructions for device cleaning
Start the motor and blow impurities and dust out of the vent holes
of the device� Use protective goggles for this operation� Clean the
external plastic parts by a wet rag and mild detergent� Though
these parts are made of the materials resistant to solvents, NEVER
use any solvent�
Instructions for cleaning the charger
ATTENTION! Risk of electric shock. Prior to start han-
dling the charger, disconnect the line plug from the
socket!
Impurities and dust can be removed from external charger surfaces
by a rag or a non-metal brush� Use neither water nor detergents�
ATTENTION! With respect to protection from el. shock
and preservation of the class of protection, all mainte-
nance and service operations requesting jig saw case
removal must be performed by the authorized service
centre only!
The current list of authorized service centres can be found at our
website www.narex.cz, section "Service centres"�

Accessories

The accessories recommended for use with this device are availa-
ble commercially in the shops with hand el� tools�
Accumulator's state of charge
100 %
less than 60 %
less than 30 %
Method of returning to
operation
Release and then press the
power switch again
Replace the battery if needed
Release and then press the
power switch again
Reduce the load on the ma-
chine
down
The machine cannot be restart-
ed without service intervention
Bring the machine to an
authorised service centre