Using Your Ceramic Cooktop - Westinghouse WFE904SD User Manual

USING YOUR CERAMIC COOKTOP

Switching the ceramic cooktop on and off
CONTROL PANEL DISPLAY
Switch on
Touch for 2 seconds
/
Switch off Touch
for 2 seconds
/ none
TIPS & INFORMATION TIPS AND INFORMATION
After switching on, within approx. 10 seconds a heat
setting or a function must be set, otherwise the appliance
automatically switches itself off.
Setting the heat setting
CONTROL PANEL DISPLAY
To increase
Touch to
To decrease Touch
to
To switch off
Touch until
TIPS AND INFORMATION TIPS & INFORMATION
The keep warm setting lies between and
It is used to keep food warm.
Switching the outside ring on and off
By switching the outside rings on or off, the
effective heating surface can be matched to the size
of the cookware.
TIPS AND INFORMATION TIPS & INFORMATION
Before an outside ring can be switched on, the inside ring
must be switched on.
TRIPLE CONTROL
INDICATOR LIGHT
COOKING ZONE PANEL
To switch on the Two indicator lights
Touch for
middle ring are lit
1-2 seconds
To switch on the Three indicator
Touch for
outside ring lights are lit
1-2 seconds
To switch off the The third indicator
Touch for
outside ring light goes out
1-2 seconds
The second
To switch off the
Touch for
indicator light goes
middle ring
1-2 seconds
out
MULTI-PURPOSE SENSOR INDICATOR
ZONE FIELD LIGHT
To switch on the
Touch for
is lit
outside ring
1-2 seconds
To switch off the
Touch for
goes out
outside ring
1-2 seconds
28
USING YOUR CERAMIC COOKTOP
Locking/unlocking the control panel
The control panel, with the exception of the 'On/Off'
sensor field, can be locked at any time in order to
prevent the settings being changed eg. By wiping over
the panel with a cloth.
CONTROL
DISPLAY
PANEL
Switch on Touch
(for 5 seconds)
the previously set
Switch off Touch
heat settings
TIPS & INFORMATION
TIPS AND INFORMATION
When you switch the appliance off, the locking function
is automatically switched off.
Using the automatic warm-up function
All cooking zones are equipped with an automatic warm
up function. When setting a heat setting using
starting from , the cooking zone switches to full power
for a certain amount of time and then automatically
switches back to the heat setting set.
.
POSSIBLE
CONTROL
HEAT
PANEL
SETTINGS
Switch on
(only when
Touch to
starting at )
Switch off Touch
to /
Not used Touch
to
TIPS & INFORMATION TIPS AND INFORMATION
If during the automatic warm up a higher heat
setting is selected, e.g. from to , the automatic
warm up is adjusted.
If there is still residual heat on the cooking zone
(display ), the automatic warm up is not performed.
The length of time that the automatic warm up function
operates depends on the heat setting selected.
HEAT SETTING
, when
Using the child safety device
The child safety device prevents unintentional use of
the appliance.
Switching on the child safety device
DISPLAY
STEP CONTROL PANEL
(after
1.
5
on (Do not set a heat
seconds)
setting)
to
2.
Touch
to
The child safety device is switched on
Switching off the child safety device
STEP CONTROL PANEL
1.
on (Do not set a heat
setting)
2.
Touch
3.
off
The child safety device is switched off
The child safety device can only be switched on or off,
if no heat setting is set.
Overriding the child safety device
The child safety device can be switched off in
this way for a single cooking session; it remains
AUTOMATIC WARM UP (MIN:SEC) activated afterwards.
0.30
STEP
1.00
1.
1.40
4.50 2.
6.30 Until the appliance is next switched off, it can be used
as normal. After switching off the appliance, the child
10.10
safety device is active again.
2.00
TIPS & INFORMATION TIPS AND INFORMATION
3.30
After overriding the child safety device, a heat setting
4.30
or a function must be set within approx. 10 seconds,
otherwise the appliance automatically switches itself off.
– – –
DISPLAY
Switch the appliance
for 4 seconds
DISPLAY
Switch the appliance
for 4 seconds
lights up
Switch the appliance
CONTROL PANEL DISPLAY
Switch the appliance
on
Touch for 4 seconds
lights up
29
USING YOUR CERAMIC COOKTOP