Table of Contents
Advertisement
Quick Links
3 in 1 Multi Sensor
PST07
PST07-A
PST07-C
PST07-B
PST07-D
1
The multi-sensor PST07 has PIR, temperature and light sensors
function in one, based on Z-Wave
The multi sensor is a Z-Wave
TM
with any Z-Wave
enabled network. This device is a security enabled
Z-Wave Plus product that is able to use encrypted Z-Wave Plus
messages to communicate to other security enabled Z-Wave Plus
TM
products. Z-Wave
enabled devices displaying the Z-Wave
also be used with it regardless of the manufacturer, and ours can also
be used in other manufacturer's Z-Wave
The product supports Over The Air(OTA) feature for the products
firmware upgrade.
This product can be included and operated in any Z-Wave
with other Z-Wave
TM
certified devices from other manufacturers and/or
other applications. All non-battery operated nodes within the network
will act as repeaters regardless of vendor to increase reliability of the
network.
The device adopt the Z-Wave
network system is all made by Z-Wave
network system will have the advantages as below.
Concurrent multi-channel support reduces external interference.
•
Better RF range, improve about 10 meters in indoor.
•
Support 100 Kbps transmit speed, speed up communication.
•
Specification
Rated
RF distance
RF Frequency
TM
technology.
TM
enabled device which is fully compatible
TM
enabled networks.
TM
500 series chip, when your Z-Wave
TM
500 series devices. The
DC3V (CR123A)
Min. 40M indoor,
100M outdoor line of sight,
868.40 MHz, 869.85 MHz(EU)
TM
logo can
TM
network
TM
Advertisement
Table of Contents
Related Manuals for Philio PST07
Summary of Contents for Philio PST07
- Page 1 3 in 1 Multi Sensor The multi-sensor PST07 has PIR, temperature and light sensors PST07 function in one, based on Z-Wave technology. The multi sensor is a Z-Wave enabled device which is fully compatible with any Z-Wave enabled network. This device is a security enabled...
-
Page 2: Troubleshooting
920.9MHz, 921.7MHz, 923.1MHz(TW/SG/Thai/KR) RF Maximum Power +5dBm ALS Sensing Range 0-10000 lux Temperature Sending Range -10 to 40° C Dimension 89*83*62 91.4g (PST07-A), Weight 96.0g (PST07-D) IP classification IPX4 Operation temperature -10 to 40° C FCC ID RHHPST07 Marking CE/NCC ... -
Page 3: Function Description
Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable. 1. Pressing button four times and keep about 5 seconds. Reset 2. IDs are excluded and all settings will reset to factory default. Add to/Remove from Z-Wave Network There are two tamper keys in the device, one is in the back side,... - Page 4 Notice 1: Always RESET a Z-Wave device before trying to add it to a Notification Report (V8) Z-Wave network Notification Type: Home Security (0x07) Event: Tampering. Product covering removed (0x03) Z-Wave Notification * Temperature Report: When the PIR motion detected state changed, the device will After the device adding to the network, it will wake-up once per day in unsolicited to send the “Sensor Multilevel Report”...
-
Page 5: Power Up Procedure
* Timing Report: Beside the event triggered could report message, the device also COMMAND_CLASS_VERSION_V3 support the timing unsolicited report of the status. COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 Battery level report: Every 6 hours report once in default. COMMAND_CLASS_DEVICE_RESET_LOCALLY • It could be changed by setting the configuration NO. 8. COMMAND_CLASS_ASSOCIATION_V2 Low battery report: When the battery level is too low. -
Page 6: Choosing A Suitable Location
Choosing a Suitable Location 1. The recommended mounting height is 160cm 2. Don't let the device facing the window or the sunlight. 3. Don't let the device facing the source of heat. For instance the heater or the air-condition. Battery Installation When the device reports the low battery message, users should replace the battery. -
Page 7: Z-Wave Configuration Settings
Z-Wave Configuration Settings Name Description Def. Valid Name Description Bit7: Reserve. Def. Valid Customer function switch, using bit Setting the BASIC command value to turn control. on the light. The 0x63 means turn on Basic Set Bit0: Tamper On/Off (1:On, 0:Off) 0 ~ 99 the light. -
Page 8: Z-Wave Supported Command Class
Name Description Name Description Def. Def. Valid Valid seconds per tick, default tick is 7 (70 degree Fahrenheit, it will continue report. seconds). Enable this functionality will cause some 0 means never send turn off light issue please see the detail in the command. -
Page 9: Fcc Interference Statement
They can take this product for Highest granted Security Class Notification environmental safe recycling. Firmware Update Meta Data Highest granted Security Class Philio Technology Corporation 8F., No.653-2, Zhongzheng Rd., Xinzhuang Dist., New Taipei City None Supervision 24257, Taiwan(R.O.C) None Transport Service http://www.philio-tech.com... - Page 10 Consult the dealer or an experienced radio/TV technician for • help. 警語: This device complies with Part 15 of the FCC Rules. Operation is subject 「取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻 to the following two conditions: 率、加大功率或變更原設計之特性及功能。 (1) This device may not cause harmful interference, and 低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立...