Function List - Hitachi WJ200-004MF Manual

Table of Contents

Function List

If a desired parameter is not displayed, check the setting of function "b037"(function code display restriction). To display all parameters, specify "00" for "b037".

Code

d001

Output frequency monitoring

d002

Output current monitoring

d003

Rotation direction minitoring

d004

Process variable (PV), PID feedback monitoring

d005

Intelligent input terminal status

d006

Intelligent output terminal status

d007

Scaled output frequency monitoring

d008

Actual-frequency monitoring

d009

Torque command monitoring

d010

Torque bias monitoring

d012

Torque monitoring

d013

Output voltage monitoring

d014

Power monitoring

d015

Cumulative power monitoring

d016

Cumulative operation RUN time monitoring

d017

Cumulative power-on time monitoring

d018

Heat sink temperature monitoring

d022

Life-check monitoring

d023

EzSQ program counter

d024

EzSQ program number

d025

User monitor 1

d026

User monitor 2

d027

User monitor 3

d029

Position setting monitor

d030

Position feedback monitor

d050

Dual monitor

d060

Inverter mode monitor

d080

Trip Counter

d081 – d086 Trip info. 1–6 (factor)

d090

Warning monitor

d102

DC voltage monitoring (across P and N)

d103

BRD load factor monitoring

d104

Electronic thermal overload monitoring

F001

Output frequency setting

F002

Acceleration (1) time setting

F202

Acceleration (1) time setting, 2nd motor

F003

Deceleration (1) time setting

F203

Deceleration (1) time setting, 2nd motor

F004

Keypad Run key routing

A001

Frequency source setting

A201

Frequency source setting, 2nd motor

A002

Run command source setting

A202

Run command source setting, 2nd motor

A003

Base frequency setting

A203

Base frequency setting, 2nd motor

A004

Maximum frequency setting

A204

Maximum frequency setting, 2nd motor

A005

[AT] selection

A011

Pot./O-L input active range start frequency

A012

Pot./O-L input active range end frequency

A013

Pot./O-L input active range start voltage

A014

Pot./O-L input active range end voltage

A015

Pot./O-L input start frequency enable

A016

External frequency filter time constant

A017

Easy sequence function selection

Function Name

0.00 to 99.99 / 100.0 to 400.0 [Hz]

0.0 to 655.3 [A]

F (Forward) / o (Stop) / r (Reverce)

0.00 to 99.99 in steps of 0.01/100.0 to 999.9 in steps of 0.1/1000. to 9999. in steps of 1/

1000 to 9999 in steps of 10/ 100 to 999 in units of 1000

(Example)

7, 5, 3, 1 : ON

6, 4, 2 : OFF

(Example)

11 : ON

AL, 12 : OFF

0.00 to 99.99 / 100.0 to 999.9 / 1000. to 9999. / 1000 to 3999

-400. to -100. / -99.9 to -10.0 / -9.99 to -0.00 / 0.00 to 99.99 / 100.0 to 400.0 [Hz]

-200 to +200 [%]

0.0 to 600.0 [V]

0.0 to 999.9 [kW]

0.0 to 999.9 in steps of 1 kW/h, or the unit set for function "b079"/

1000 to 9999 in units of 10 kW/h, or the unit set for function "b079"/

100 to 999 in units of 1000 kW/h, or the unit set for function "b079"

0. to 9999. in units of 1 hour/ 1000 to 9999 in units of 10 hours / 100 to 999 in units of 1,000 hours

-20.0 to 150.0 [ ºC]

1: Capacitor on

main circuit board

2: cooling-fan (same as WAF signal)

0 to 1024

0000 to 9999

-2147483647 to 2147483647

-268435455 to 268435455

Displays two different data configured in b160 and b161.

Displays currently selected inverter mode : I-C / I-V

0. to 9999. in units of 1 trip / 1000 to 6553 in units of 10 trips

Factor code

Warning code

0.0 to 999.9 / 1000. [V]

0.0 to 100.0 [%]

0 / "start frequency" to "maximum frequency" [Hz]

0.01 to 99.99 / 100.0 to 999.9 / 1000. to 3600. [s]

00 (Foward) / 01 (Reverce)

00 (keypad potentiometer) / 01 (control circuit terminal block) / 02 (digital operator) / 03 (Modbus) /

04 (option) / 06 (pulse train input) / 07 (easy sequence) / 10 (operation function result)

01 (control circuit terminal block) / 02 (digital operator) /

03 (Modbus) / 04 (option)

30.0 to "maximum frequency (1st)" [Hz]

30.0 to "maximum frequency (2nd)" [Hz]

"Base frequency (1st)" to 400.0 [Hz]

00 (switching between O and OI terminals) /

02 (switching between O terminal and keypad potentiometer) /

03 (switching between OI terminal and keypad potentiometer)

0.00 to 99.99/100.0 to 400.0 [Hz]

0 to 100 [%]

00 (A011) / 01 (0Hz)

1 to 30 / 31

00 (disabled) / 01 (PRG terminal) / 02 (Always)

Setting Range

OFF

Lifetime expired

Normal

[ ○ = Allowed × = Not parmitted]

Setting During

Change During

Default

Operation

Setting

(allowed or not)

—

○

—

○

—

0.00

○

10.00

○

10.00

○

10.00

○

10.00

○

0.00

○

0.00

○

100

○

Table of Contents

This manual is also suitable for:

Wj200 series

Function List - Hitachi WJ200-004MF Manual

Function List

Related Manuals for Hitachi WJ200-004MF

Related Content for Hitachi WJ200-004MF

This manual is also suitable for:

Table of Contents