Hitachi WJ200-004MF Manual page 16

Function List
Code
b088 Restart mode after FRS
b089 Automatic carrier frequency reduction
b090
Dynamic braking usage ratio
b091
Stop mode selection
b092 Cooling fan control
b093
Accumulated time clear of the cooling fan
b094 Initialization target data setting
b095 Dynamic braking control (BRD) selection
b096 BRD activation level
b097 BRD register
b100 Free-setting V / F freq. (1)
b101
Free-setting V / F volt. (1)
b102 Free-setting V / F freq. (2)
b103 Free-setting V / F volt. (2)
b104 Free-setting V / F freq. (3)
b105 Free-setting V / F volt. (3)
b106 Free-setting V / F freq. (4)
b107
Free-setting V / F volt. (4)
b108 Free-setting V / F freq. (5)
b109 Free-setting V / F volt. (5)
b110 Free-setting V / F freq. (6)
b111 Free-setting V / F volt. (6)
b112 Free-setting V / F freq. (7)
b113
Free-setting V / F volt. (7)
b120 Brake control enable
b121 Brake Wait Time for Release
b122 Brake Wait Time for Acceleration
b123 Brake Wait Time for Stopping
b124 Brake Wait Time for Confirmation
b125 Brake release freq. setting
b126 Brake release current setting
b127 Braking frequency
b130 Over-voltage LADSTOP enable
b131 Over-voltage LADSTOP level
b132 DC bus AVR constant setting
b133 DC bus AVR for decel. Proportional-gain
b134
DC bus AVR for decel. Integral-time
b145 GS input performance selection
b150 Panel Display selection
b160 1st parameter of Double Monitor
b161 2nd parameter of Double Monitor
b163 Data change mode selection of d001 and d007
b164
Automatic return to the initial display
b165 Action selection in case of external operator disconnection
b166 Data Read / Write selection
b171 Inverter mode selection
b180 Initialization trigger
b190 Password A setting
b191 Password A for authentication
b192
Password B setting
b193 Password B for authentication
16
Function Name
00 (starting with 0 Hz) /
01 (starting with matching frequency) /
02 (starting with active matching frequency)
00 (disabled) /
01 (enabled [output current controlled]) /
02 (enabled [fin temperature controlled])
0.0 to 100.0 [%]
00 (deceleration until stop) /
01 (free-run stop)
00 (fan always ON) /
01 (ON fan only during inverter operation
02 (fin temperature controlled)
00 (count) / 01 (clear)
00 (All parameters) /
01 (All parameters except in/output terminals and communication) /
02 (Uxxx) / 03 (expect Uxxx)
00 (disabled) /
01 (enabled [disabled while the inverter is stopped]) /
02 (enabled [enabled also while the inverter is stopped])
330 to 380 / 660 to 760 [V]
Set range : minimum connectable register
Rbmin to 600.0 [Ω]
0. to b102 [Hz]
0.0 to 800.0 [V]
0. to b104 [Hz]
0.0 to 800.0 [V]
0. to b106 [Hz]
0.0 to 800.0 [V]
0. to b108 [Hz]
0.0 to 800.0 [V]
0. to b110 [Hz]
0.0 to 800.0 [V]
0. to b112 [Hz]
0.0 to 800.0 [V]
0. to 400 ( to 1000) [Hz]
0.0 to 800.0 [V]
00 (disabled) / 01 (enabled)
0.00 to 5.00 [s]
0.00 to 5.00 [s]
0.00 to 5.00 [s]
0.00 to 5.00 [s]
0.00 to 99.99 / 100.0 to 400.0 [Hz]
Set range: 0 to 200% of inverter rated current [A]
0.00 to 99.99 / 100.0 to 400.0 [Hz]
00 (disabled) / 01 (enabled) / 02 (enabled with acceleration)
330 to 395 / 660 to 790 [V]
0.10 to 30.00 (s)
0.00 to 5.00
0.0 to 150.0 [s]
00 (non Trip) / 01 (Trip)
d001 to d060
d001 to d030
d001 to d030
00 (disabled) / 01 (enabled)
00 (disabled) / 01 (enabled)
00 (tripping) / 01 (tripping after decelerating and stopping the motor) /
02 (ignoring errors) / 03 (stopping the motor after free-running) /
04 (decelerating and stopping the motor)
00 (read / write enable) / 01 (both read, write disable)
00 (disabled) / 01 (IM enabled)/03 (Permanent Magnet Motor)
00 (disabled) / 01 (enabled)
0 (disabled) / 0001 to FFFF (enabled)
0000 to FFFF
0 (disabled) / 0001 to FFFF (enabled)
0000 to FFFF
Setting Range
[including 5 minutes after power-on and power-off] ) /
[ ○ = Allowed × = Not parmitted]
Setting During Change During
Default
Operation Operation
Setting
(allowed or not) (allowed or not)
× 00
○
× × 01
× 0.0
○
× 00
○
× 01
○
× × 00
× × 00
× 01
○
× 360 / 720
○
Min.
×
○
resistance
× × 0.
× × 0.0
× × 0.
× × 0.0
× × 0.
× × 0.0
× × 0.
× × 0.0
× × 0.
× × 0.0
× × 0.
× × 0.0
× × 0.
× × 0.0
× 00
○
× 0.00
○
× 0.00
○
× 0.00
○
× 0.00
○
× 0.00
○
Rated current
×
○
of inverter
× 0.00
○
× 00
○
× 380 / 760
○
× 1.00
○
0.20
○ ○
1.0
○ ○
× 00
○
001
○ ○
001
○ ○
002
○ ○
00
○ ○
00
○ ○
02
○ ○
× 00
○
× × 00
× × 00
× × 0000
× × 0000
× × 0000
× × 0000