Ferroli OMNIA M 3.2 Installation And Owner's Manual page 161

3.1 HEAT MODE Enable or disable the heating mode
The refresh time of climate related curves for heating
3.2 t_T4_FRESH_H
mode
The maximum ambient operating temperature for heating
3.3 T4HMAX
mode
The minimum ambient operating temperature for heating
3.4 T4HMIN
mode
3.5 dT1SH The temperature difference for starting the unit (T1)
3.6
dTSH The temperature difference for starting the unit (Ta)
The setting temperature 1 of climate related curves for
3.8 T1SetH1
heating mode
The setting temperature 2 of climate related curves for
3.9 T1SetH2
heating mode
The ambient temperature 1 of climate related curves for
3.10 T4H1
heating mode
The ambient temperature 2 of climate related curves for
3.11 T4H2
heating mode
The type of zone1 end for heating mode 0=FCU(fan coil
3.12 ZONE1 H-EMISSION
unit)
The type of zone2 end for heating mode 0=FCU(fan coil
3.13 ZONE2 H-EMISSION
unit)
the time that the compressor has run before starting the
3.14 t_DELAY_PUMP
pump.
The minimum operating ambient temperature for cooling in
4.1 T4AUTOCMIN
auto mode
The maximum operating ambient temperature for heating
4.2 T4AUTOHMAX
in auto mode
5.1 WATER FLOW TEMP. Enable or disable the WATER FLOW TEMP.:0=NON,1=YES
5.2 ROOM TEMP. Enable or disable the ROOM TEMP.:0=NON,1=YES
Enable or disable the ROOM THERMOSTAT DOUBLE
5.3 DOUBLE ZONE
ZONE:0=NON,1=YES
The style of room thermostat
6.1 ROOM THERMOSTAT
SET,2=ONE ZONE,3=DOUBLE ZONE
The temperature difference betw een T1S and T1 for
7.1 dT1_IBH_ON
starting the backup heater.
The time that the compressor has run before the first
7.2 t_IBH_DELAY
backup heater turns on
7.3 T4_IBH_ON The ambient temperature for starting the backup heater
The temperature difference betw een T1S and T1B for
7.4 dT1_AHS_ON
turning the additional heating source on
The time that the compressor has run before starting the
7.5 t_AHS_DELAY
additional heating source
The ambient temperature for starting the additional
7.6 T4_AHS_ON
heating source
7.7 IBH_LOCATE IBH/AHS installation location PIPE LOOP=0; BUFFER TANK=1
7.8 P_IBH1 Power input of IBH1
7.9 P_IBH2 Power input of IBH2
7.10 P_TBH Power input of TBH
The target outlet w ater temperature for space heating
8.1 T1S_H.A_H
w hen in holiday aw ay mode
The target outlet w ater temperature for domestic hot
8.2 T5S_H.A_DHW
w ater heating w hen in holiday aw ay mode
PREHEATING FOR The setting temperature of outlet w ater during first
12.1
FLOOR T1S preheating for floor
12.3 t_FIRSTFH The time last for preheating floor
1=RAD.(radiator) 2=FLH(floor heating)
1=RAD.(radiator) 2=FLH(floor heating)
0=NON,1=MODE
62
1 0 1
0.5 0.5 6
25 20 35
-15 -25 15
5 2 10
2 1 10
35 25 60
28 25 60
-5 -25 35
7 -25 35
1 0 2
2 0 2
2 2 20
25 20 29
17 10 17
1 0 1
0 0 1
0 0 1
0 0 3
5 2 10
30 15 120
-5 -15 10
5 2 10
30 5 120
-5 -15 10
0 0 0
0 0 20
0 0 20
2 0 20
25 20 25
25 20 25
25 25 35
72 48 96
1 /
0.5 hours
1
1
1
1
1
1
1
1
1 /
1 /
0.5 MIN
1
1
1 /
1 /
1 /
1 /
1
5 MIN
1
1
5 MIN
1
0
0.5
kW
0.5
kW
0.5 kW
1
1
1
12 HOUR