Directed MIT4 Firmware Specific Manual
  1. Manuals
  2. Brands
  3. Directed Manuals
  4. Automobile Accessories
  5. MIT4
  6. Firmware specific manual
Directed MIT4 Firmware Specific Manual

Directed MIT4 Firmware Specific Manual

Directed digital system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Directed Digital System
MIT4
Firmware Specific Guide
This product is intended for installation by a professional
installer only! Attempts to install this product by a person
other than a trained professional may result in severe
damage to a vehicle's electrical system and components.
© 2015 Directed, Vista, CA
Directed Digital System 2015-08

Advertisement

Table of Contents
loading

Related Manuals for Directed MIT4

Summary of Contents for Directed MIT4

  • Page 1 This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components. © 2015 Directed, Vista, CA Directed Digital System 2015-08...

  • Page 2: Table Of Contents

    Contents Warning! Safety first ........................3 Introduction ............................ 4 Vehicle application guide ......................4 Wiring connections ......................... 5 Main power harness (H1), 12-pin thick gauge connector ............... 5 Auxiliary output harness (H2), 16-pin black connector ..............5 Analog harness (H3), 18-pin white connector ................6 MC501 harness (H4), 8 thick-gauge wires (optional) ..............

  • Page 3: Warning! Safety First

    This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately.

  • Page 4: Introduction

    Introduction The MIT4 firmware for Directed Digital Systems is a complete solution for remote start, security (if applicable), bypass interface, and convenience needs compatible with specific MITSUBISHI vehicles. Warning! This module can only be programmed via the web tool, which can be found on www.directechs.com or using the Directechs Mobile application for smartphones.

  • Page 5: Wiring Connections

    If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. Directed Digital System MIT4 © 2015 Directed. All rights reserved.

  • Page 6: Analog Harness (H3), 18-Pin White Connector

    If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. The Green wire is only required for starter kill and antigrind applications. Directed Digital System MIT4 © 2015 Directed. All rights reserved.

  • Page 7: Installation

    The siren is only compatible with hybrid systems. The green wire is only required for starter kill and antigrind connections. All adapters are displayed from the wire side (unless specified otherwise). Directed Digital System MIT4 © 2015 Directed. All rights reserved.

  • Page 8: Type 2

    The siren is only compatible with hybrid systems. The green wire is only required for starter kill and antigrind connections. All adapters are displayed from the wire side (unless specified otherwise). Directed Digital System MIT4 © 2015 Directed. All rights reserved.

  • Page 9: Type 3

    The green wire is only required for starter kill and antigrind connections. Unlock* wire from Remote Starter *Lock: Same procedure have to be done for missing Lock wire. All adapters are displayed from the wire side (unless specified otherwise). Directed Digital System MIT4 © 2015 Directed. All rights reserved.

  • Page 10: Type 4

    The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory hood pin. The siren is only compatible with hybrid systems. All adapters are displayed from the wire side (unless specified otherwise). Directed Digital System MIT4 © 2015 Directed. All rights reserved.

  • Page 11: Installation Type 1

    Ground Vehicle chassis Locating components for type 1 CAN Low: CAN High: Black Brown OBDII Diagnostic Connector - 16-pin black CAN Low: Black, pin 14 CAN High: Brown, pin 6 Directed Digital System MIT4 © 2015 Directed. All rights reserved.
  • Page 12 Ignition Switch Connector - 6-pin white (left side of steering column) (+) 12V: White, pin 1 (+) Ignition: Green, pin 2 (+) Accessory: Yellow, pin 4 (+) Starter: Pink, pin 5 Directed Digital System MIT4 © 2015 Directed. All rights reserved.

  • Page 13: Installation Type 2

    Parking Lights Green/White C-208 White Junction Block Lock Violet C-217 White Junction Block Unlock Lt. Green/Red C-217 White Junction Block Door Trigger Lt. Green C-204 White Junction Block Ground Vehicle chassis Directed Digital System MIT4 © 2015 Directed. All rights reserved.
  • Page 14 Ignition Connector - 6-pin blue (+) 12V: Blue/Yellow, pin 1 (+) Ignition: Red or Black/White, pin 2 (+) Accessory 1: Blue/Red, pin 4 (+) Starter: Black/Yellow, pin 5 (+) Accessory 2: Blue/Black, pin 6 Directed Digital System MIT4 © 2015 Directed. All rights reserved.

  • Page 15: Installation Type 3

    Parking Lights Green/White C-208 White Junction Block Lock/Arm Lt. Green/Black C-217 White Junction Block Unlock/Disarm Red/Green C-217 White Junction Block Door Trigger Lt. Green C-204 White Junction Block Ground Vehicle chassis Directed Digital System MIT4 © 2015 Directed. All rights reserved.
  • Page 16 Parking Lights Green/White C-208 White Junction Block Lock/Arm Lt.Green/Bkack C-217 White Junction Block Unlock/Disarm Red/Green C-217 White Junction Block Door Trigger Lt. Green C-204 White Junction Block Ground Vehicle chassis Directed Digital System MIT4 © 2015 Directed. All rights reserved.

  • Page 17: Installation Type 4

    Green/White C-208 White Junction Block Violet/White Lock/Arm C-217 White Junction Block or Violet Unlock/Disarm Lt.Green/Red C-217 White Junction Block Door Trigger Lt. Green C-204 White Junction Block Ground Vehicle chassis Directed Digital System MIT4 © 2015 Directed. All rights reserved.
  • Page 18 Parking Lights Green/White C-208 White Junction Block Lock Violet C-217 White Junction Block Unlock Lt. Green/Red C-217 White Junction Block Door Trigger Lt. Green C-204 White Junction Block Ground Vehicle chassis Directed Digital System MIT4 © 2015 Directed. All rights reserved.
  • Page 19 Ground When Running Ignition Switch (left side of steering column) Eclipse & Eclipse Spyder: white connector Endeavor & Galant: black connector (-) Keysense: Blue/Red, pin 6 Directed Digital System MIT4 © 2015 Directed. All rights reserved.

  • Page 20: Connecting The Module

    Manual or automatic transmission selection The yellow loop on the Directed Digital System controls which transmission type the unit is configured for. The state of the loop (uncut or cut) when the main module is powered up will determine which type is selected.

  • Page 21: Optional Sensors

    Please follow the instructions included with the kit for appropriate installation and programming information. When flashing the Directed Digital System, make sure to pick the remote you will be using. This way the main module will have the necessary firmware to interact with the remote and Control Center (antenna) combination.

  • Page 22: Module Programming

    Connect all but the white 12-pin harness Connect all the harnesses to the Directed Digital System, EXCEPT the white12-pin main power harness. Must be connected LAST Connect the white12-pin main power harness, and wait until the LED turns &...

  • Page 23: Led Diagnostics And Troubleshooting

    Used to ensure the module received the command received. ignition command. Flashes red & orange START ON command Used to ensure the module received the start received. command. Flashes green quickly Directed Digital System MIT4 © 2015 Directed. All rights reserved.

  • Page 24: Hard Reset

    After 3 seconds the LED turns ON solid orange. Keep holding the & & programming button until the LED flashes red, then orange slowly. Solid Hold Flashes Release the programming button. The LED turns ON solid red. & Solid Release Directed Digital System MIT4 © 2015 Directed. All rights reserved.

  • Page 25: Learning The Tach (Not Needed With Virtual Tach)

    Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature in the configuration wizard to adjust the starter output time in 50mS increments to compensate for such an occurrence. Directed Digital System MIT4 © 2015 Directed. All rights reserved.

  • Page 26: Limited Lifetime Consumer Warranty

    Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;...

  • Page 27: Quick Reference Guide - Viper, Clifford, Python, Avital & Automate (Regular Key)

    Press the Lock button on the factory or aftermarket remote.* Press Lock on The vehicle engine will shut Off after locking either remote* the system. * Your aftermarket remote may differ from the model shown in the illustrations. Directed Digital System MIT4 © 2015 Directed. All rights reserved.
  • Page 28 Pit stop mode SmartStart compatible Stop the vehicle in a safe parking spot and put the This system is compatible with Directed SmartStart 3.0. For a complete list of gear in Park (P). On manual transmission vehicle, gear in supported features, please visit www.mysmartstart.com.

  • Page 29: Quick Reference Guide - Autostart (Regular Key)

    1 to 5. Turn ignition OFF and remove the key from the Key OUT Key IN ignition barrel. START Exit the vehicle. Exit vehicle Directed Digital System MIT4 © 2015 Directed. All rights reserved.
  • Page 30 SmartStart compatible vehicle is now in Idle Mode. Press Remote Start button* This system is compatible with Directed SmartStart 3.0. For a complete list of Turn ignition OFF and remove the key from the supported features, please visit www.mysmartstart.com. Key OUT...

Table of Contents