Related Manuals for Directed 933.SUBARU2
Summary of Contents for Directed 933.SUBARU2
- Page 1 933.SUBARU2 DS3+ / DS4+ v1.38.195.3 2010 Subaru Outback THSUN1 Compatible (Sold Separately)
-
Page 2: Table Of Contents
Contents Introduction Vehicle function compatibilities Pre-installation and application warnings Installation Wiring diagram with T-Harness (THSUN1) Wiring diagram Locating components in the vehicle Vehicle connections Module programming For Security-Only and Convenience-Only programming, see next sections. Module programming for convenience only (skip transponder) Module programming for security-only installations Pairing remotes Connecting the module... -
Page 3: Introduction
To configure via DirectLink DT (mobile app): 1. Follow and complete the wiring diagram(s) related to your installation through the app. 2. When installation is complete, select Configure DS4/DS4+. 3. Follow the on-screen instructions. 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved. -
Page 4: Vehicle Function Compatibilities
Control of aftermarket alarm with OEM remote Entry Monitoring Trunk/Hatch Pin Fuel level/EV battery level Brake Status (foot brake) Key2GO E-Brake Status * Odometer Ignition Status Immobilizer Bypass-Data No Key Req'd 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved. -
Page 5: Pre-Installation And Application Warnings
[6] External relay: When using an external relay, use a 1N4002 diode or larger. [7] Clutch Output: Connection required only for manual transmission. [8] THSUN1: When using the THSUN1 T-harness, an external relay is required for (-) Negative clutch connection. 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved. -
Page 6: Wiring Diagram With T-Harness (Thsun1)
(+) 12V (+) 12V Security Only Remote Start Only Only required for Remote Start + Security Pit Stop mode or NOT USED manual transmission vehicles. Type 1 1A Diode (1N4002+) 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved. -
Page 7: Wiring Diagram
(+) Starter 2: 17 16 White/Orange Remote Start Only White/Green, pin 6 27 26 Remote Start + Security Ignition Switch 34 33 Immo. Data: White/Blue, pin 31 (black or white connector) 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved. -
Page 8: Locating Components In The Vehicle
7 6 5 19 18 (-) Ground 27 26 35 34 (+)12V (-) Key Release 1: Black/Red, pin 4 Legend: Mandatory Connections Security Only Remote Start Only Remote Start + Security 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved. -
Page 9: Vehicle Connections
Security Only (+) Siren Output H2/12 Pink No Connection No Connection H2/13 Violet No Connection No Connection H2/14 Brown No Connection No Connection H2/15 White/Blue No Connection No Connection 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved. - Page 10 6 pin plug, pin 5 yellow Remote Start Only H4/5 (+) 12 Volt Input ignition switch, white 6 pin plug, pin 3 white (40A) Remote Start Only 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved.
- Page 11 Green H6/4 Temperature sensor harness, 2-pin black connector (H7) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color Connection H7/1 Black Temperature Sensor H7/2 Black Temperature Sensor 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved.
-
Page 12: Module Programming
For more information, refer to the Tach Learning procedure section. * Your aftermarket remote may differ from the model shown in the illustrations. You have successfully completed the module programming sequence. 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved. -
Page 13: Module Programming For Convenience Only (Skip Transponder)
Your aftermarket remote may differ from the model shown in the illustrations. You have successfully completed the module programming sequence. 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved. -
Page 14: Module Programming For Security-Only Installations
Your aftermarket remote may differ from the model show in the illustration. You have successfully completed the module programming sequence. 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved. -
Page 15: Pairing Remotes
When used in conjunction with Directed SmartStart ® To enable D2D communication between the DS3+/DS4+ and the Directed SmartStart one of the following actions must be performed ® before providing power to the Directed SmartStart unit: ®... -
Page 16: When Used In Conjunction With Smartstart
DO NOT connect the Directed SmartStart ® 2-pin power harness when using the DS3+/DS4+. Power and ground will be provided by the D2D connector on the module. Refer to the Directed SmartStart ® documentation for further details. D2D port configuration Caution! Do not connect the Control Center (antenna) or any digital sensors (8504D) to the white D2D1 port. -
Page 17: Manual Transmission
Manual Transmission IMPORTANT! Directed does not approve nor support installations of manual transmission and remote starts on any electronic vehicles (EV), OEM Remote Start Activation firmware, vehicles with convertibles and/or removable tops, including but not limited to Jeep Wrangler, Honda S2000, Mazda Miata, and other such vehicles. -
Page 18: Led Diagnostics And Troubleshooting
Flashes red x 7 Keysense was not supported in data. Refer to “Installation (wiring diagrams & vehicle wiring reference Keysense not detected. charts)” to check the connections. Flashes red x 9 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved. - Page 19 The smart key was not detected, which prevents the system from shutting down the vehicle. Flashes red x 3 Speed was detected. The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved.
-
Page 20: Soft Reset
DS3+: Release the programming button. The LED turns solid red. & Solid Release DS4+: Release the programming button. The LED turns ON blue for 1 second then solid red. & & Solid Solid x1 Sec Release 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved. -
Page 21: Tach Learning Procedure (Not Needed With Virtual Tach)
Therefore, there is no Over-Rev protection. If the vehicle attempts to remote start, but is unsuccessful, the remote start will keep the ignition on for the entire runtime period. 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved. -
Page 22: Limited Lifetime Consumer Warranty
This Warranty gives you specific legal rights and you may also have other rights which vary from state to state. VOXX DEI LLC, 2351 J. Lawson Blvd., Orlando, Florida 32824 933.SUBARU2 1.38.195.3 2010 Subaru Outback ©2022 VOXX•DEI LLC. All rights reserved. -
Page 23: Quick Reference Guide (Customer Copy)
3 possible ways you can send commands to your vehicle, using the: in Park (P). • Factory remote. • Aftermarket remote. Press the Remote Start button on the transmitter.* • Directed SmartStart application via your smartphone. & Parking lights The parking lights will flash once to indicate the vehicle is Press... - Page 24 The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.