Table of Contents
Advertisement
Quick Links
INSTALLATION GUIDE
MIT6
Designed by Installers for Installers
© 2019 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
2019-09-11
Directed Digital
Solutions
Advertisement
Table of Contents
Related Manuals for Directed Directechs MIT6
Summary of Contents for Directed Directechs MIT6
- Page 1 MIT6 Designed by Installers for Installers © 2019 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.
-
Page 2: Table Of Contents
Contents Warning! Safety first ........................3 Introduction ............................ 4 Pre-installation and application warnings ..................4 Vehicle application guide ......................5 Wiring connections ......................... 6 Main power harness (H1), 12-pin thick gauge connector ............... 6 Auxiliary output harness (H2), 16-pin black connector ..............6 Analog harness (H3), 18-pin white connector ................ -
Page 3: Warning! Safety First
The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation. -
Page 4: Introduction
Introduction The MIT6 firmware for Directed Digital Solutions is compatible with specific Mitsubishi vehicles. It is a complete solution for remote start, security (if applicable), bypass interface, and convenience. This guide provides information on the installation of the module using MIT6. If you would prefer using this system as a digital solution, go to www.directechs.com and search for the make, model and year of the vehicle. -
Page 5: Vehicle Application Guide
DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status Directed Digital Solutions MIT6 © 2019-09-11 Directed. All rights reserved. -
Page 6: Wiring Connections
If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. Directed Digital Solutions MIT6 © 2019-09-11 Directed. All rights reserved. -
Page 7: Analog Harness (H3), 18-Pin White Connector
If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. The Green wire is only required for starter disable and anti-grind applications. Directed Digital Solutions MIT6 © 2019-09-11 Directed. All rights reserved. -
Page 8: Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)
(+) Parking Lights (right): White/Black, pin 6 Black/White, pin 3 (+) Ignition: Brown/Red, pin 2 C-418 ( white conn.at BCM) (+) Starter: Violet, pin 5 (+) Accessory: Blue/Red, pin 6 Directed Digital Solutions MIT6 © 2019-09-11 Directed. All rights reserved. - Page 9 Parking Lights (right) Black/White C-418 connector at BCM. White Parking Lights (left) White/Black C-418 connector at BCM. White Red/Black C-410 connector at BCM. Black Key Sense Blue Key Sense connector. White Directed Digital Solutions MIT6 © 2019-09-11 Directed. All rights reserved.
-
Page 10: Connecting The Module
Manual or automatic transmission selection The yellow loop on the Directed Digital Solutions controls which transmission type the unit is configured for. The state of the loop (uncut or cut) when the main module is powered up will determine which type is selected. -
Page 11: Optional Sensors
When flashing the Directed Digital Solutions, make sure to pick the remote you will be using. This way the main module will have the necessary firmware to interact with the remote and Control Center (antenna) combination. -
Page 12: Module Programming
Connect all but the 12-pin harness Connect all the harnesses to the Directed Digital Solutions, EXCEPT the 12-pin main power harness. Must be connected LAST Connect the 12-pin main power harness, and wait until the LED turns ON solid red. -
Page 13: Led Diagnostics And Troubleshooting
External module synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 Directed Digital Solutions MIT6 © 2019-09-11 Directed. All rights reserved. - Page 14 The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 Analog error codes Description Troubleshooting DEI feature error. A feature config file mismatch was detected. Please contact Technical Support. Flashes red, green & orange Directed Digital Solutions MIT6 © 2019-09-11 Directed. All rights reserved.
-
Page 15: Soft Reset
A module reset will only erase the steps performed in "Module programming" on page 12. The firmware and settings flashed to the module will not be affected. Connect all but the If required for your installation, connect all the harnesses to the Directed Digital Solutions, 12-pin harness EXCEPT the 12-pin main power harness. Press and hold the programming button, then connect the 12-pin harness to the module. -
Page 16: Learning The Tach (Not Needed With Virtual Tach)
Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature in the configuration wizard to adjust the starter output time in 50mS increments to compensate for such an occurrence. Directed Digital Solutions MIT6 © 2019-09-11 Directed. All rights reserved. -
Page 17: Limited Lifetime Consumer Warranty
Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;... -
Page 18: Quick Reference Guide
SmartStart compatible * Icon and remote appearance may differ depending on the model purchased. This system is compatible with Directed SmartStart. For a complete list of supported Pit stop/idle mode features, please visit www.mysmartstart.com. Stop the vehicle in a safe parking spot and put the... - Page 19 The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet.
Need help?
Do you have a question about the Directechs MIT6 and is the answer not in the manual?
Questions and answers