Page 1
20V max* LITHIUM-ION CORDLESS DRILL/DRIVER 054-1332-6 IMPORTANT: INSTRUCTION Read and understand this instruction manual MANUAL thoroughly before using the product.
TABLE OF CONTENTS Technical Specifications Safety Guidelines Key Parts Diagram Operating Instructions Maintenance Troubleshooting Parts List Warranty NOTE: If any parts are missing or damaged, or if you have any questions, please call our toll-free helpline at 1-800-689-9928. SAVE THESE INSTRUCTIONS •...
SAFETY GUIDELINES: WARNING! Safety symbols in this Instruction Manual are used to flag possible dangers. The safety symbols and their explanations require your full understanding. The safety warnings do not, by themselves, eliminate any danger, nor are they substitutes for proper accident prevention measures.
Page 6
headline bars headline bars headline bars model no. 054-1332-6 | contact us 1-800-689-9928 • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. ELECTRICAL SAFETY • Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.
Page 7
• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second. POWER TOOL USE AND CARE • Do not force the power tool.
Page 8
headline bars headline bars headline bars model no. 054-1332-6 | contact us 1-800-689-9928 • Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury. •...
Page 9
• Before performing any kind of work on the machine (e.g., maintenance, tool change, etc.) as well as when transporting and storing it, always set the direction-of-rotation switch to the centre (locked) position. Unintentional activation of the On/Off switch may result in personal injury.
Page 10
headline bars headline bars headline bars model no. 054-1332-6 | contact us 1-800-689-9928 SAFETY GUIDELINES FOR CHARGER WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. WARNING! To reduce the risk of electric shock or damage to the charger and battery, use only the continuation tabs...
Page 11
• The extension cord is properly wired and in good electrical condition. • The wire size is large enough for the AC ampere rating of the charger as specified below: Cord Length (Feet) 25’ 50’ 100’ Cord Size (AWG) NOTE: AWG = American Wire Gauge •...
OPERATING INSTRUCTIONS KNOW YOUR LITHIUM-ION RECHARGEABLE BATTERY 80-100% Charge 60-79% Charge 40-59% Charge 20-39% Charge Under 20% Charge Completely Discharged Fuel gauge This Lithium-Ion battery pack is equipped with a Fuel Gauge, which displays the remaining charge of the battery pack. Press the Fuel Gauge button to display the LED lights. The LED lights will stay lit for approximately 4 seconds.
Page 14
headline bars headline bars headline bars model no. 054-1332-6 | contact us 1-800-689-9928 COLD WEATHER OPERATION When the battery pack is very cold, it may “pulse” for the first minute of use to warm itself. Put the battery pack on the tool and use the tool in a light application. After about a minute, the battery pack will have warmed itself and will operate normally.
Page 15
LED INDICATOR ON CHARGER Battery Pack Green LED Indicator Explanation Status Charging will begin when battery HI/LO TEMP. Hot/Cold battery ------- returns to 5°C (41°F)–40°C (104°F) (SEE MANUAL) DEFECTIVE Defective Flashing -------- Battery pack is defective BATTERY BATTERY Charging -------- Flashing Charging CHARGING...
Page 16
headline bars headline bars headline bars model no. 054-1332-6 | contact us 1-800-689-9928 TRIGGER SWITCH (fig 3) fig 3 To turn the drill/driver ON, depress the trigger switch. To turn it OFF, release the trigger switch. VARIABLE SPEED (fig 3) Variable Direction- The variable-speed trigger switch delivers higher...
Page 17
KEYLESS CHUCK (fig 5) fig 5 Open The arrows on the keyless chuck indicate the direction of rotation of the body of the chuck to GRIP (tighten) or OPEN (release) the jaws of the chuck on the drill/driver bit. Keyless Chuck Grip ADJUSTABLE TORQUE CLUTCH (fig 6)
Page 18
headline bars headline bars headline bars model no. 054-1332-6 | contact us 1-800-689-9928 BIT STORAGE (fig 7) fig 7 Bit Clip When not in use, the bits that are provided with the cordless drill/driver may be stored on either side of the cordless drill/driver by snapping the bit into place in the bit clip.
Page 19
GENERAL DRILLING (fig 9) fig 9 1. Use a vise or clamps to secure the material to be drilled to keep it from turning as the drill bit rotates. 2. Check the direction-of-rotation selector for the correct setting (forward or reverse). 3.
Page 20
headline bars headline bars headline bars headline bars headline bars headline bars model no. 054-1332-6 | contact us 1-800-689-9928 DRILLING MODE OPERATION For drilling in wood, use twist bits, spade bits, power auger bits or hole saws. 1. When drilling “through” holes, place a block of wood behind the workpiece to prevent ragged or splintered edges on the back side of the hole.
MAINTENANCE BEFORE EACH USE The tool may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air. Before each use: 1. Inspect the cordless drill/driver, the trigger switch, and the cord for damage. 2.
Page 22
headline bars headline bars headline bars headline bars headline bars headline bars model no. 054-1332-6 | contact us 1-800-689-9928 CHUCK REMOVAL (fig 10) fig 10 Mallet The chuck can be removed and replaced with a new one. 1. Lock the trigger switch by placing the direction-of- rotation selector in the centre position.
TROUBLESHOOTING Problem Possible Causes Solution The drill/driver does not Battery is depleted Charge the battery work Chuck is not opened Open the chuck Bit cannot be installed Bit does not fit the chuck Use suitable bit Be sure cooling vents are Clean, clear vents.
This Mastercraft product is guaranteed for a period of 3 years from the date of original retail purchase against defects in workmanship and materials, except for the following components: a) Component A: Batteries, chargers and carrying case, which are guaranteed for a period of 2 years from the date of original retail purchase against defects in workmanship and materials;...
Page 26
The provisions contained in this warranty are not intended to limit, modify, take away from, disclaim or exclude any statutory warranties set forth in any applicable provincial or federal notes notes notes legislation. Made in China Imported by Mastercraft Canada Toronto, Canada M4S 2B8 warnings warnings warnings...
Need help?
Do you have a question about the 5268 and is the answer not in the manual?
Questions and answers