Subscribe to Our Youtube Channel
Related Manuals for MasterCraft 054-2015-6
Summary of Contents for MasterCraft 054-2015-6
- Page 1 054-2015-6 CORDED HAMMER DRILL WITH 50-PIECE ACCESSORY KIT INSTRUCTION IMPORTANT: MANUAL Please read this manual carefully before running this hammer drill and save it for reference...
-
Page 2: Table Of Contents
TABLE OF CONTENTS TECHNICAL SPECIFICATIONS SAFETY GUIDELINES PACKAGE CONTENTS OPERATION INSTRUCTIONS 10-16 TROUBLESHOOTING KEY PARTS DIAGRAM EXPLODED VIEW PARTS LIST WARRANTY 21-22 SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions.Read all instructions and follow them with use of this product... -
Page 3: Technical Specifications
model no.054-2015 l contact us 1.800.689.9928 TECHNICAL SPECIFICATIONS SAFETY GUIDELINES: 120 V, 60 Hz, 6A Motor Safety symbols in this instruction manual are used to flag possible dangers. The safety symbols 0 2700 RPM (no load) － Variable speeds and their explanations require your full understanding. The safety warnings do not, by themselves, 0 43,200 BPM (no load) －... - Page 4 model no.054-2015 l contact us 1.800.689.9928 GENERAL POWER TOOL SAFETY WARNINGS Do not operate power tools in explosive atmospheres, such as in the presence of Do not overreach. Keep proper footing and balance at all times. This enables better control of flammable liquids, gases or dust.
-
Page 5: Package Contents
model no.054-2015 l contact us 1.800.689.9928 Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss. Package Contents: Use the auxiliary handles, if supplied with the tool. Loss of control can cause personal injury. Corded hammer drill, auxiliary handle with depth-stop rod, chuck key, 50-piece accessory kit, and instruction manual Hold the power tool by the insulated gripping surfaces when performing an operation where 50-piece accessory kit... -
Page 6: Operation Instructions
model no.054-2015 l contact us 1.800.689.9928 OPERATING INSTRUCTIONS Direction-of-rotation selector (Fig. 3) Variable-speed trigger switch (Fig. 1) The direction of bit rotation is reversible and is cont rolled by a selector located above the trigger switch. The variable-speed trigger switch delivers higher speed with increased trigger pressure and lower speed With the drill held toward you: with decreased trigger pressure. - Page 7 model no.054-2015 l contact us 1.800.689.9928 Installing bits (Fig. 5) Auxiliary handle (Fig. 4) 1. Unplug the hammer drill from the power source. The tool must be supported with the auxiliary handle, which can be swiveled and locked into 12 positions 2.
- Page 8 model no.054-2015 l contact us 1.800.689.9928 Drilling in wood Fig. 6 For maximum performance, use high-speed steel or brad-point bits for wood drilling. 1. Begin drilling at a very low speed to prevent the bit from slipping off the starting point. 2.
-
Page 9: Troubleshooting
model no.054-2015 l contact us 1.800.689.9928 Before each use TROUBLESHOOTING 1. Inspect the hammer drill, the trigger switch, the cord and the accessories for damage. PROBLEM POSSIBLE CAUSES SOLUTIONS 2. Check for damaged, missing, or worn parts. 3. Check for loose screws, misalignment or binding of moving parts, or any other condition that may The motor does not start The tool is not connected to a Connect the tool to a power... -
Page 10: Key Parts Diagram
model no.054-2015 l contact us 1.800.689.9928 KEY PARTS DIAGRAM EXPLODED VIEW Chuck jaws Chuck Chuck key holes Chuck sleeve Hammer/drilling selection switch Depth-stop gauge Lock-on button Chuck key Chuck key strap 10. Switch trigger Auxiliary handle 12. Direction-of-rotation selector Before attempting to use this tool, become familiar with all of its operating features and safety requirements. -
Page 11: Parts List
Steel ball Screw Ball bearing Carbon brush This Mastercraft product is guaranteed for a period of 3 years from the date of original retail purchase Retaining ring Spring against defects in workmanship and materials, except for the following components: Gear 1... - Page 12 model no.054-2015 l contact us 1.800.689.9928 g) this warranty will not apply to any product or part thereof if any part from another manufacturer is installed therein or any repairs or alterations have been made or attempted by unauthorized persons; h) this warranty will not apply to normal deterioration of the exterior finish, such as, but not limited to, scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive and chemical cleaners;...
Need help?
Do you have a question about the 054-2015-6 and is the answer not in the manual?
Questions and answers