Page 2
Please clarify your application environment before deployment, in case the device can function well. The device is not intended to be used as a reference sensor, and Ursalink will not should responsibility for any damage which may result from inaccurate readings.
Sensor data are transmitted in real-time using standard LoRaWAN protocol. LoRaWAN enables encrypted radio transmissions over long distance while consuming very little power. The user can obtain sensor data and view the trend of data change through Ursalink Cloud or thr ough the user's own Network Server.
EM500-PT100 User Guide Probe Type Straight tube (By default) Power Supply 19000 mAh Li-SoCl battery Battery Life 6 year (10 min interval, SF12) >10 year (10 min interval, SF7) Operating Temperature -20°C to +70°C Relative Humidity 0% to 100% (non-condensing) Dimension 105 ×...
EM500-PT100 User Guide If any of the above items is missing or damaged, please contact your Ursalink sales representative. 2.2 Product Overview Front View: ①LoRa Antenna (Internal) ②NFC Area ③Water-proof Connector Back View: ④Battery (Internal) ⑤Wall Mounting Holes ⑥Pole Mounting Holes 3.
EM500-PT100 User Guide 3. Pull out the motherboard, insert and lock 4. Put the motherboard back and restore the wires accordingly (see the label on the everything in its due position. motherboard or following picture). Pinouts: Color Description White Note: Select one of the PT cables to connect.
DIN rail on the mounting bracket. It is necessary to choose a standard bracket. 5. Turn ON/OFF the Sensor EM500-PT100 series can be turned ON/OFF via smartphone or computer with NFC (Near Field Communication) or button. Select one of following methods to turn on/off the sensor.
Page 9
EM500-PT100 User Guide 3. Attach the smartphone with NFC area to the device. Note: Ensure the location of your smartphone NFC area and it is recommended to take off phone case before using NFC. 4. Device information will be shown on the APP.
EM500-PT100 User Guide 5.2 Turn ON/OFF via PC Software 1. Download Ursalink configuration software “Toolbox” and open the software. 2. Connect NFC reader to computer and attach the device to NFC reader. 3. Select type as NFC and serial port of NFC reader, then click “save”.
6. Enter password (default password:123456) and press Enter key to change device status. 5.3 Turn ON/OFF via Button 1. Remove screws on the bottom of EM500-PT100 and take off the upper enclosure. 2. Find the button beside the battery. 3.Press the button until LED blinks to turn on or off the device. (about 3 seconds) Press the button until LED blinks rapidly to reset the device to factory default.
EM500-PT100 User Guide 6.1.1 Read Configuration 1. Open APP “Toolbox” and click “Read” to read current information of device. 2. Attach the smartphone with NFC area to the device until the APP shows “Read Successfully!”. Note: Failing to read can be caused by long distance, wrong location, or rapid movement.
EM500-PT100 User Guide 3. Enter password (default password: 123456). 4. Attach the smartphone with NFC area to the device and wait a few seconds until APP shows “Write Successfully!”. The device will automatically re-join the network if LoRaWAN parameters are changed.
Page 14
EM500-PT100 User Guide 2. Attach the smartphone with NFC area to another device. 3. Select the template file from Toolbox APP and click “Write”. 4. Enter password of this device and keep the two devices close until the APP shows “Write successfully!”.
EM500-PT100 User Guide 6.2 Configuration via PC Make sure “Toolbox” is downloaded on your computer. 6.2.1 Read Configuration 1. Open software “Toolbox” and click “Read” to read current information of device. 3. Attach the device to the NFC reader until Toolbox shows “success”.
EM500-PT100 User Guide 3. Press Enter key to write and attach the device close to NFC reader until “Write” button disappear. The device will automatically re-join the network if LoRaWAN paramters are changed. Note: Keep the two devices close and don’t move them in order that you can get the best connectivity as possible when writing data via NFC.
EM500-PT100 User Guide 6.2.3.2 FOTA 1. Make sure your computer can access the Internet. 2. Click “Check for Updates” to search for the latest firmware via computer Internet and upgrade. Note: Keep the two devices close and don’t move them in order that you can get the best connectivity as possible when upgrading.
MAC command. Enabled Disabled: Whatever how the signal quality is, the Network Server will not adjust the datarate of the device. 7.1.2 Basic Settings-ABP Location: Ursalink ToolBox(PC): LoRaWAN Settings → Basic Ursalink ToolBox(APP): Device → Settings → LoRaWAN Setting...
Page 20
EM500-PT100 User Guide Basic Settings-ABP Item Description Default Enter the application EUI.The Network Server receives request and consults the entity associated with the 24e124c0002 App EUI APP EUI to validate the request.If permission is a0001 granted, it responds with a join-accept message.
Ursalink ToolBox(PC): LoRaWAN Settings → Channel Ursalink ToolBox(APP): Device → Settings → LoRaWAN Settings Note: Make sure the LoRa channel configuration of EM500-PT100 matches the LoRaWAN gateway. LoRa frequency configuration is as follows if the sensor LoRa frequency is one of...
16 channels numbered 80 to 95 utilize LoRa 125 kHz BW starting at 486.3 MHz and incrementing linearly by 1.6 MHz to 489.3. 7.2 Device Settings 7.2.1 General Location: Ursalink ToolBox(PC): Device Settings → General Ursalink ToolBox(APP): Device → Settings → General Settings Device General Settings Item Description Default Device Type Show the type of the device.
7.2.2 Data Calibration Location: Ursalink ToolBox(PC): Device Settings → Data Calibration Settings Ursalink ToolBox(APP): Device → Settings → Data Calibration Settings Note: It is recommended to do the calibration before using the device. Data Calibration Settings Item...
8.1 Ursalink Cloud Registration Register and log in Ursalink Cloud. Ursalink Cloud URL: https://cloud.ursalink.com/login.html 8.2 Add a Ursalink LoRaWAN Gateway 1. Enable “Ursalink” type network server and “Ursalink Cloud” mode in gateway web GUI. Note: Ensure gateway has accessed the Internet.
2.Go to “My Devices->Gateway” of Ursalink Cloud and click “Add” to add gateway to Ursalink Cloud via SN. 3.Check if gateway is online in Ursalink Cloud. 8.3 Add EM500-PT100 to Cloud 1. Go to “Device->My Devices” and click “Add Device”. Fill in the SN of EM500-PT100 and select associated gateway.
Page 26
EM500-PT100 User Guide 2.After EM500-PT100 is connected to Ursalink Cloud, Click or “History Data” to check the data on Ursalink cloud. -END-...