Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for PXM PxArt+ 6
Summary of Contents for PXM PxArt+ 6
- Page 1 PX390 PxArt+ 6 MANUAL...
-
Page 2: Table Of Contents
Declaration of conformity....................Manufacturer reserves the right to make modifications in order to improve device operation. Rev 1.1 tel.: (12) 626 46 92 PXM Marek Żupnik spółka komadytowa for Firmware 2.19 fax: (12) 626 46 94 ul. Przemysłowa 12 E-mail: info@pxm.pl 30-701 Kraków... -
Page 3: General Description
1. GENERAL DESCRIPTION PxArt+ 6 is a professional LED illuminator designed for illumination of museum exhibitions or displays. Thanks to the application of the most modern semiconductor SSL LED light sources and advanced control electronics, a high class illuminator was created which meets very high requirements for museum and exhibition lighting. - Page 4 From a distance of more than 2.0 m from the outer housing of the lamp and LEDs, the light is harmless to unprotected eyes. While working outdoors in normal conditions, the housing unit can heat up to +60°C. Make sure that accidental contact with the device during use is impossible. In case of improper usage of the product it may cause a risk of serious injury or death, because of the threat of fire.
-
Page 5: Version Data
The dimming of the lamp brightness occurs when the temperature is above 70 °C; this prevents the device from overheating. If the device reaches a temperature of 90 °C, the power of the lamp will be totally reduced. The light is then switched automatically in the event of temperature drop below the maximum temperature (90°C). -
Page 6: Lamp Description
4. LAMP DESCRIPTION a 3-phase track for GLOBAL ® Trac Pulse control end feed DMX+ DMX- power cable DMX cable (shielded cable, 2-core cable) GLOBAL Trac GAC 600 adapter... -
Page 7: Manual Change Of Lamp Settings
5. MANUAL CHANGE OF LAMP SETTINGS The lamp has been equipped with buttons which allow for changing the brightness level and colour temperature of light. The buttons have been placed at the bottom part of the junction box, above the lamp reflector. One button is responsible for one parameter. The available buttons and connector for connecting the PX277 programmer have been shown in the figure below: Parameter programming... -
Page 8: Co-Operation With The Px277 Configurator
6. CO-OPERATION WITH THE PX277 CONFIGURATOR Lamp settings can be changed by connecting the PX277 PxArt Settings Controller configurator. At the moment of connection, the PX390 starts again which causes LEDs to be off for a while and the diode indicating the DMX signal condition pulses for 2 seconds. When the device is turned on, its name appears on the display. -
Page 9: Description Of The Information Parameters
6.1. Description of the information parameters PX277 controller allows you to read important information concerning the lamp to which it has been connected. Model Lamp model PX390 +6 MW NEXT Lamp operation time (total operation time of the lamp, also Lighting time without diodes turned on) and lighting time are presented as 00y 001d 06h:48m... -
Page 10: Invert Colour
Model PX390 +6 MW NEXT Bright. address Bright. address ENTER 001 * NEXT Bright. address 512 * 6.2.2 Invert color The [Invert color] function applies both to Model PX390 +6 MW normal operation of DMX and operation in no NEXT signal mode. -
Page 11: Smoothing
6.2.4 Smoothing The device also has the smoothing option which enables smooth brightness and colour modifications. When the function is turned on, the transitions between successive DMX values sent to the lamp (responsible for brightness and colour changes) occur smoothly, without visible jolts, which prevents light "vibration"... -
Page 12: Response To The Lack Of Dmx Signal
PX390 default setting: Color address ź Brightness address ź Model PX390 +6 MW Scene color ź Scene brightness ź NEXT Invert color ź ENTER Default sett. Default sett. Flicker free ź PREV+NEXT > 2s PREV+ NEXT Smooth Time ź Default sett. Smooth time 200 [ms] ź... -
Page 13: Dmx Signal And Power Supply Connection
7. DMX SIGNAL AND POWER SUPPLY CONNECTION 7.1. GLOBAL Trac GAC 600 adapter DMX CONTACTS DMX - (on the opposite side DMX +) POWER CONTACTS earth phase 1 (phase 2 on the opposite side) neutral (phase 3 on the opposite side) phase selector switch ®... -
Page 14: Rdm Description Of Available Parameters
8. RDM DESCRIPTION OF AVAILABLE PARAMETERS PX390 supports the DMX-RDM protocol. DMX protocol in its assumption enables one-way data flow while its extension, the RDM protocol, can transmit information in two ways. This makes the simultaneous receiving and sending of information possible and allows for monitoring the operation of devices compatible with the RDM protocol as well as gives the possibility of changing the configuration of their parameters. - Page 15 Description Parameter name TEMPERATURE_LIMIT_ 0x800E temperature limitation activation for the temperature sensor connected to the driver, ON/OFF For 0 value, the function is not active; for 1 value, the function is active. Default value is 1. TEMPERATURE_ 0x800F lower temperature value for which the temperature limitation is being activated THRESHOLD_LOW TEMPERATURE_...
-
Page 16: Device Programming
9. DEVICE PROGRAMMING Model PX390 +6 MW NEXT ENTER Color address Color address 001 * NEXT NEXT Color address 512 * Bright. address ENTER Bright. address 001 * NEXT NEXT Bright. address ENTER 512 * Scene color Scene color 001 * NEXT NEXT Scene color... -
Page 17: Dimensions
10. DIMENSIONS Ø 92 Dimensions are given in millimetres... -
Page 18: Technical Data
11. TECHNICAL DATA Power supply: 230 V AC Number of LEDs: Power input: 10 W Max. increase of the housing temp.: + 30° C Luminous flux: 600 lumens Lifetime of diodes: 50 000 h Angles of reflectors: 10°, 20°, 30°, 40°, EL Color temperature: 2700÷4500 K Brightness regulation extension:... -
Page 19: Declaration Of Conformity
30-701 Kraków fax: 12 626 46 94 DECLARATION OF CONFORMITY according to guide lines 2004/108/WE and 2006/95/WE Name of producer: PXM Marek Żupnik sp. k. Address of producer: ul. Przemysłowa 12 30-701 Kraków declares that the product: Name of product:...
Need help?
Do you have a question about the PxArt+ 6 and is the answer not in the manual?
Questions and answers