Table of Contents
Advertisement
Quick Links
LD-G-5
für Gleichstrommotoren
Locomotive decoder
Décodeur pour locomotive
avec moteur continu
voor gelijkstroommotoren
Art.-Nr. 22-01-040 / 22-01-41
Lokdecoder
DCC-Format
for DC engines
DCC format
Format DCC
Locdecoder
DCC-format
n
n
n
n
n
n
n
n
n
Anleitung
n
Manual
n
Mode d´emploi
n
Handleiding
n
n
n
n
Advertisement
Table of Contents
Related Manuals for tams elektronik LD-G-5
Summary of Contents for tams elektronik LD-G-5
- Page 1 LD-G-5 Lokdecoder für Gleichstrommotoren DCC-Format Locomotive decoder for DC engines DCC format Décodeur pour locomotive Anleitung avec moteur continu Manual Format DCC Locdecoder Mode d´emploi voor gelijkstroommotoren Handleiding DCC-format Art.-Nr. 22-01-040 / 22-01-41...
- Page 2 © 02/2006 Tams Elektronik GmbH Alle Rechte, insbesondere das Recht der Vervielfältigung und Verbreitung sowie der Übersetzung vorbehalten. Vervielfältigungen Reproduktionen jeglicher Form bedürfen schriftlichen Genehmigung durch die Tams Elektronik GmbH. Deutsch Technische Änderungen vorbehalten. © 02/2006 Tams Elektronik GmbH English rights reserved.
-
Page 3: Table Of Contents
LD-G-5 English Table of contents How to use this manual Intended use Safety instructions EMC declaration Information: Speed mode Information: Configuration variables (CVs) Operation overview Technical specifications Checking the package contents Required tools and materials Safe and correct soldering Mounting the locomotive decoder... -
Page 4: How To Use This Manual
English LD-G-5 How to use this manual If you have no specialist technical training, this manual gives step-by- step instructions for safe and correct fitting of the module, and operation. Before you start, we advise you to read the whole manual, particularly the chapter on safety instructions and the FAQ chapter. -
Page 5: Safety Instructions
LD-G-5 English Safety instructions Mechanical hazards Cut wires can have sharp ends and can cause serious injuries. Watch out for sharp edges when you pick up the PCB. Visibly damaged parts can cause unpredictable danger. Do not use damaged parts: recycle and replace them with new ones. - Page 6 English LD-G-5 Fire risk Touching flammable material with a hot soldering iron can cause fire, which can result in injury or death through burns or suffocation. Connect your soldering iron or soldering station only when actually needed. Always keep the soldering iron away from inflammable materials.
-
Page 7: Emc Declaration
LD-G-5 English EMC declaration This product is developed in accordance with the European standards EN 55014 and EN 50082-1, tested corresponding to the EC - directive 89/336/EWG (EMVG of 09/11/1992, electromagnetic tolerance) and meets legal requirements. To guarantee the electromagnetic tolerance you must take the following precautions: §... -
Page 8: Operation Overview
LD-G-5 Operation overview The decoder LD-G-5 is designed for operation in DCC format and can be adjusted to one of 127 basic addresses or to one of 10.239 extended addresses. It is designed to be controlled from digital control units that are set on the 14-, 28 or the 128-speed mode. - Page 9 LD-G-5 English § Alternative velocity characteristic for mode 28 speed levels (CV#67 to 94) * Not possible with central units with register programming! Driving of the motor With the factory settings the motor is driven with a PWM of 400 Hz. In case of a noisy or unquiet operation of the motor, the PWM frequency may be adjusted by changing the values of CV#9.
- Page 10 English LD-G-5 Acceleration and brake delay It is possible to program the acceleration and brake delay individually via the central unit. Emergency stop By setting a CV-variable it is possible to adjust how an emergency stop is carried out. There are the following possibilities: §...
-
Page 11: Technical Specifications
LD-G-5 English Technical specifications Data format Supply voltage 12-24 Volt digital voltage Current consumption (without connected loads) approx. 10 mA Max. current for motor 800 mA Max. current per function output 100 mA Max. total current 1.000 mA Protected to... -
Page 12: Safe And Correct Soldering
English LD-G-5 § a small side cutter and wire stripper, § a pair of tweezers, § tin solder (0,5 mm. diameter), § wire (diameter: > 0,05 mm² for all connections). Safe and correct soldering Caution: Incorrect soldering can cause dangers through fires and heat. Avoid these dangers by reading and following the directions given in the chapter Safety instructions. -
Page 13: Mounting The Locomotive Decoder
LD-G-5 English § After soldering check (preferably with a magnifying glass) tracks for accidental solder bridges and short circuits. This would cause faulty operation or, in the worst case, permanent damage. You can remove excess solder by putting a clean soldering tip on the spot. - Page 14 English LD-G-5 Front lighting: X5 Back lighting: X4 Accessory to be switched via F1: X6 Caution: If you connect the accessories to the return conductor for all functions (point X1), the load must be insulated. The loads should not make contact with metal parts of the locomotive.
- Page 15 LD-G-5 English number of LEDs connected in series to one output depends on the digital voltage. You can determine the number of the LEDs that can be connected in series to one output from the following formula: (number of LEDs + 2) x 1,5 < digital voltage...
-
Page 16: Programming The Locomotive Decoder
English LD-G-5 Programming the locomotive decoder The locomotive decoder is programmed from the digtial central. See chapter in the manual of your digital control unit where the programming of configuration variables (CVs) is explained. You can programm resp. read out the following locomotive decoder variables: NB. - Page 17 LD-G-5 English CV-name Remarks Input value (State of delivery) Braking rate 0 ... 255 = Length of the delay before the switching to the next lower (16) speed level when locomotive braking. delay is calculated as described in CV#3. Maximum 0 ...
- Page 18 English LD-G-5 CV-name Remarks Input value (State of delivery) Configuration Numerical value * data 1 Direction "standard" Reverse direction 14 speed levels 28 or 128 speed levels Linear velocity characteristic Alternative velocity characteristic Basic adress Extended adress Assignment 0 ... 15 Numerical value * F5 –...
- Page 19 LD-G-5 English CV-name Remarks Input value (State of delivery) Dimming of 0 ... 63 = The voltage that is applied to the outputs: the output. (63) The value "1" corresponds to the minimum, „63“ to the maximum voltage. Assignment 0 ... 31 Numerical value * F0 –...
-
Page 20: Faq
English LD-G-5 § Parts are getting very hot and/or start to smoke. Disconnect the system from the mains immediately! Possible cause: one or more connections are soldered incorrectly. à Check the connections. Possible cause: The connection of the motor is connected to locomotive ground. -
Page 21: Conditional Warranty
LD-G-5 English Conditions of warranty This product is guaranteed for two years. The warranty includes the correction of faults which can be proved to be due to material failure or factory flaw. guarantee adherence technical specifications of the circuit when assembled and connected according to the manual. - Page 22 LD-G-5 LD-G-5 Fig. 1: Anschlußplan – Connections Plan de connexion - Aansluitplan Seite - Page - Page - Pagina I Seite - Page - Page - Pagina I...
- Page 23 LD-G-5 LD-G-5 Fig. 2: Schaltplan - Circuit diagram - Schéma de principe - Schakelschema Seite - Page - Page - Pagina II Seite - Page - Page - Pagina II...
- Page 24 Actuele informatie en tips: http://www.tams-online.de Garantie und Service: Warranty and service: Garantie et service: Garantie en service: Tams Elektronik GmbH Rupsteinstraße 10 D-30625 Hannover fon: ++49 (0)511 / 55 60 60 fax: ++49 (0)511 / 55 61 61 e-mail: modellbahn@tams-online.de...