Table of Contents
Advertisement
Quick Links
Lastgeregelter Lokdecoder
für Gleichstrommotoren
DC engines - Motorola format
Décodeur avec compensation de
charge pour locomotive avec
moteur continu - Format Motorola
Lastgeregelde Locdecoder
voor gelijkstroommotoren
LD-G-10
Motorola-Format
Locomotive Decoder
with load control for
Motorola -format
Art.-Nr. 22-01-092
n
n
n
n
n
n
n
n
n
Anleitung
n
Manual
n
Mode d´emploi
n
Handleiding
n
n
n
n
Advertisement
Table of Contents
Related Manuals for tams elektronik LD-G-10
Summary of Contents for tams elektronik LD-G-10
- Page 1 LD-G-10 Lastgeregelter Lokdecoder für Gleichstrommotoren Motorola-Format Locomotive Decoder with load control for Anleitung DC engines - Motorola format Décodeur avec compensation de Manual charge pour locomotive avec Mode d´emploi moteur continu - Format Motorola Lastgeregelde Locdecoder Handleiding voor gelijkstroommotoren Motorola -format...
- Page 2 © 09/2007 Tams Elektronik GmbH Alle Rechte, insbesondere das Recht der Vervielfältigung und Verbreitung sowie der Übersetzung vorbehalten. Vervielfältigungen und Reproduktionen jeglicher Form bedürfen schriftlichen Genehmigung durch die Tams Elektronik GmbH. Deutsch Technische Änderungen vorbehalten. English © 09/2007 Tams Elektronik GmbH All rights reserved.
-
Page 3: Table Of Contents
LD-G-10 English Table of contents How to use this manual Intended use Safety instructions EMC declaration Operation overview Technical specifications Checking the package contents Required tools and materials Safe and correct soldering Mounting the locomotive decoder Programming the locomotive decoder... -
Page 4: How To Use This Manual
English LD-G-10 How to use this manual This manual gives step-by-step instructions for safe and correct fitting of the module, and operation. Before you start, we advise you to read the whole manual, particularly the chapter on safety instructions and the FAQ chapter. -
Page 5: Safety Instructions
LD-G-10 English Safety instructions Mechanical hazards Cut wires can have sharp ends and can cause serious injuries. Watch out for sharp edges when you pick up the PCB. Visibly damaged parts can cause unpredictable danger. Do not use damaged parts: recycle and replace them with new ones. - Page 6 English LD-G-10 Fire risk Touching flammable material with a hot soldering iron can cause fire, which can result in injury or death through burns or suffocation. Connect your soldering iron or soldering station only when actually needed. Always keep the soldering iron away from inflammable materials.
-
Page 7: Emc Declaration
LD-G-10 English EMC declaration This product is developed and tested in accordance with the European standards EN 55014-1 and EN 61000-6-3 and meets the EC - directive 2004/108/EG and legal requirements. To guarantee the electromagnetic tolerance in operation you must take the following precautions: §... -
Page 8: Operation Overview
English LD-G-10 Operation overview The decoder is designed for operation in Motorola II format and can be adjusted to one of 255 addresses. It evaluates the digital data sent by the central unit to its address. It controls the locomotive´s motor and the driving characteristics. - Page 9 LD-G-10 English Overheating protection As soon as the decoder´s maximum operating temperature (approx. 60 °C) is exceeded the decoder automatically switches off and the locomotive´s lighting starts to flash. It is not possible to put the locomotive into operation again until the rail voltage has been switched off. As a rule the overheating is caused by a too high current consumption of the motor.
- Page 10 English LD-G-10 Speed level The decoder can drive 27 speed levels. Driving all 27 speed levels can be done only with central units which support this mode (e.g. MasterControl). With central units which only allow 14 speed levels only, it is only possible to select every second speed level.
- Page 11 LD-G-10 English Lighting The front and back lighting can be switched on and off according to the direction of travel from the central unit via the function "function"("f0"). CV programming Setting the address, the driving characteristics (starting and maximum velocity, acceleration and brake delay) and the velocity characteristic as...
-
Page 12: Technical Specifications
English LD-G-10 Technical specifications Data format Motorola I and II Supply voltage 12-24 Volt digital voltage Current consumption (without connected loads) approx. 10 mA Max. current for motor 500 mA Max. current per function output 100 mA Max. total current... -
Page 13: Safe And Correct Soldering
LD-G-10 English Safe and correct soldering Caution: Incorrect soldering can cause dangers through fires and heat. Avoid these dangers by reading and following the directions given in the chapter Safety instructions. § Use a small soldering iron with max. 30 Watt. Keep the soldering tip clean so the heat of the soldering iron is applied to the solder point effectively. -
Page 14: Mounting The Locomotive Decoder
English LD-G-10 Mounting the locomotive decoder Follow the connection diagram fig. 1. Connecting the motor Before mounting the decoder check if the locomotive motor´s current is below the maximum permissible value of 500 mA. If it is above 500 mA the decoder is not suitable for mounting in this locomotive. - Page 15 LD-G-10 English If you want to use the decoder factory settings, you have to connect the lighting and the accessories as follows: Front lighting: white wire Back lighting: yellow wire Connecting the LEDs The function outputs of the locomotive decoder switch against decoder ground.
-
Page 16: Programming The Locomotive Decoder
English LD-G-10 Programming the locomotive decoder With the most digital control units supporting the Motorola II format (e.g. Tams MasterControl, Märklin* Control Unit, Uhlenbrock* Intellibox) you can choose between two methods of programming after having started the programming mode: CV programming Online programming With the Central Station or the Mobile Station of Märklin* you can... - Page 17 LD-G-10 English Starting the programming mode Switch on the central unit or perform a reset at the central unit. Set the current address or address 80. Set all functions to "off". For current address Intellibox? or address 80: Set MM I Format.
- Page 18 English LD-G-10 Notice: Some types of central units do not allow you to access to the programming mode when the Motorola II format is set (e.g. Intellibox from Uhlenbrock*). These central units must be set to Motorola I format for the current address or the address "80". As soon as the decoder is in the programming mode, the central unit must be set back to Motorola II format.
- Page 19 LD-G-10 English CV-no. Range of values Factory settings Remarks 1, 2, 3 ... 255 Address 1, 2, 3 ... 80 Starting velocity 1, 2, 3 ... 80 Acceleration delay 1, 2, 3 ... 80 Braking delay 1, 2, 3 ... 63...
- Page 20 English LD-G-10 CV-no. Range of values Factory settings Remarks 1, 2, 3 ... 80 Lowest value of load control parameters * 30, 31 ... 255 Highest value of load control parameters * * Proceed in small steps when altering the CV#48 und #49. For most motors the factory settings meet the optimum.
- Page 21 LD-G-10 English Setting the locomotive´s address Start the programming The locomotive´s lighting flashes regularly. mode (see above) Enter the desired locomotive´s address. Switch on and off The entered address is saved. "function" (f0) once After having saved the locomotive´s address...
-
Page 22: Operation
English LD-G-10 Setting the starting and the maximum velocity Start the programming The locomotive´s lighting flashes regularly. mode (see above) Switch on function F3 The locomotive´s lighting flashes intermittently. Switch off the function F3. Turn the speed control knob until the locomotive drives with the desired starting velocity. -
Page 23: Faq
LD-G-10 English Switching the shunting gear In Motorola II format the shunting gear can be switched on and off via the auxiliary function F4. In Motorola I format the shunting gear cannot be activated. § Parts are getting too hot and/or start to smoke. -
Page 24: Manufacturer's Note
English LD-G-10 § The locomotive stops and the locomotive´s lighting starts to flash. Possible cause: The decoder has got too hot and the overheating protection has been activated. à Possibly the decoder overheating can be prevented by better cooling. à It is possible to reduce the sensitivity of the overheating protection (CV#11). -
Page 25: Conditional Warranty
LD-G-10 English Conditions of warranty This product is guaranteed for two years. The warranty includes the correction of faults which can be proved to be due to material failure or factory flaw. guarantee adherence technical specifications of the circuit when assembled and connected according to the manual. - Page 26 LD-G-10 LD-G-10 Fig. 1: Anschlussplan – Plan de connexion - Connections - Aansluitplan X1 orange / orange / orange / oranje: Motoranschluß 1 / Motor connection 1 Connexion moteur 1 / Motoraansluiting 1 X2 grau / grey / gris / grijs: Motoranschluß...
- Page 27 LD-G-10 LD-G-10 Fig. 2: Schaltplan - Circuit diagram - Schéma de principe - Schakelschema Seite - Page - Page - Pagina II Seite - Page - Page - Pagina II...
- Page 28 Actuele informatie en tips: http://www.tams-online.de Garantie und Service: Warranty and service: Garantie et service: Garantie en service: Tams Elektronik GmbH Rupsteinstraße 10 D-30625 Hannover fon: +49 (0)511 / 55 60 60 fax: +49 (0)511 / 55 61 61 e-mail: info@tams-online.de...