• The product warranty relies on the correct use, maintenance, and repair of the tool and its component parts. • Damage to parts that occurs as a result of inadequate maintenance or performed by parties other than Desoutter or their Certified Service Partners during the warranty period is not covered by the warranty.
General overview EABA tools are cordless angle-head nutrunners. They are hand-held by the operator and powered by a Desoutter battery pack. On delivery, the tool display is protected by a password. Tools are delivered with 6 Psets which are configurable from the tool display or from CVI CONFIG.
Installation Installation Installation Instructions Inserting the battery pack Insert the battery pack in front or behind the tool until a locking sound can be clearly heard. There is no ON/OFF switch: the tool is ready to operate as soon as a battery pack is mounted. When the tool is powered on, tool LEDs are blinking.
Operation Operation Configuration Instructions How to configure the tool Icons and buttons The password is enabled. The password is disabled. Press the button "Validate/Run reverse". Press the right button. Press the left button. "Validate/Run reverse" button Right button Left button Validate Save Quit...
Page 9
Operation Press this button during 2 seconds. Press this button to reach Configuration. Go to Enter password, then Pset password, use the buttons to display "1", save and and validate. The red padlock turns green. The procedure is the same to disable the Maintenance password. How to set up new passwords To set new passwords, current passwords must be disabled and the green padlock displayed.
Page 10
Operation • in.lb • kg.m • kg.cm • oz.in • dNm To change the torque unit, go to the main screen. Press this button during 2 seconds. Press this button to reach Configuration. Go to Torque unit, use the buttons to select the torque unit and validate. How to set up the reverse mode Go to the main screen.
Operation Parameter Description Start torque This is the torque value that must be reached to declare the Pset as started. Below this value, neither result or report will be generated. Angle threshold This is the torque threshold value used to start counting the angle.
Page 12
Operation Go to Enable, tick the box to enable this Pset, save and validate. Starting the tool Fit the tool with a suitable socket. Select the appropriate Pset. Hold the tool by means of the handle and apply to the fastener to be tightened. WARNING Risk Of Injury As the reaction force increases in proportion to the tightening torque, there is a risk of severe bodily injury of the operator as a result of unexpected behavior of the tool.
Page 13
Operation Angle control with torque monitoring Abort torque Max. torque Min. torque Angle threshold Pset start torque Min. angle Target angle Max. angle For tools running in severe applications, it may happen that reports are null when the battery is low. Reporting LEDs Green Yellow...
Operation LED color Description Action to do Yellow Incomplete rundown Tighten again. Yellow and red (orange) Reject report Loosen and tighten again. Above max. limits Remove and replace the fastener. How to reverse the rotation Run reverse button Press this button. Red and green LEDs are blinking alternatively.
Operation Launch CVI MONITOR to collect and display the last 100 results. Refer to the user manual of CVIMONITOR available at https://www.desouttertools.com/resource-centre. Results collection and analysis Connect the tool to a PC by using the eDOCK device. Launch CVI ANALYZER to collect and display the last 1000 results. CVI ANALYZER CVI ANALYZER is intended to analyze and import/export tightening data with results, curves, filters, profiles.
Service Service Firmware version on tool display The firmware version of the tool is displayed in the menu "Maintenance/Tool". AX.YY.ZZ. Tool information from tool display Go to "Maintenance/Tool" menu to get the following information: Total counter Number of tightenings since the manufacturing of the tool. Battery The current voltage value is displayed.
Service Right hand thread When reassembling: Apply the recommended glue. Tighten to the required torque. Lubricate with the required grease or oil. Do not apply too much grease on gears or bearings; a thin coat shall be sufficient. Instructions for transducerized tools •...
This function is set in the "Maintenance" menu. Enter the Maintenance password in the "Configuration" menu. Insert a torque transducer in line with the tool and connect it to any measuring unit from the Desoutter range. Go to "Maintenance/Calibration". Select the number of tightenings required to execute the calibration and press OK.
It is mandatory to calibrate the tool equipped with the fixed accessory before use. Upgrading tool firmware Click this icon. Click Upgrade tool firmware. Contact your Desoutter representative to get the last firmware version. Follow the instructions on screen. 06/2020 19 / 24...
1- The tool tightening counter has been reached. I038 Tool logs 1- Unexpected tool software exception. 2- Log file has been generated by the tool. 3- Contact your Desoutter representative for support. I046 Abnormal battery current 1- Abnormal battery current consumption. Check the Pset settings.
Page 21
2- Check the tool cable is not damaged. W212 Result not stored 1- It is not possible to store the tightening result in the system. 2- Contact your Desoutter representative for support. W216 Current high 1- Maximum current exceeded. 2- Contact your Desoutter representative for support.
Page 22
Procedure E223 Drive init error 1- Software failure. 2- Restart the system. 3- If the problem occurs again, contact your Desoutter representative for support. E227 Motor stalled 1- Motor stalled (could be missing phase, wrong motor tune or power electronics failure) 2- Try once again.
Page 24
Original instructions Founded in 1914 and headquartered in France, Desoutter Industrial Tools is a global leader in electric and pneumatic assembly tools serving a wide range of assembly and manufacturing operations, including Aerospace, Automotive, Light and Heavy Vehicles, Off-Road, General Industry.
Need help?
Do you have a question about the EABA 15-900 and is the answer not in the manual?
Questions and answers