Delfield 200 Series Original Instructions Manual
Hide thumbs
Also See for 200 Series:
- Brochure (8 pages) ,
- Installation, operation and maintenance manual (16 pages)
Subscribe to Our Youtube Channel
Related Manuals for Delfield 200 Series
Summary of Contents for Delfield 200 Series
- Page 1 200 & 300 Series Original Instructions Installation, Operation and Maintenance Manual This manual is updated as new information and models are released. Visit our website for the latest manual. Part Number: 9291456 11/17...
- Page 2 Safety Notices Warning This product contains chemicals known to the State Warning of California to cause cancer and/or birth defects or Read this manual thoroughly before operating, installing other reproductive harm. Operation, installation, and or performing maintenance on the equipment. Failure servicing of this product could expose you to airborne to follow instructions in this manual can cause property particles of glasswool or ceramic fibers, crystalline...
-
Page 3: Table Of Contents
Table of Contents Section 1 General Information Model Numbers ........................4 Serial Number Location ..................... 4 Warranty Information ......................4 Regulatory Certifications ....................4 Domestic Models ............................4 Export Models ............................4 Section 2 Installation Location ..........................5 Clearance Requirements ....................6 Weight Of Equipment ...................... -
Page 4: General Information
Verify warranty information, Drop-in water and ice station • View and download a copy of your warranty, 204P Drop-in ice chest with cover at www.delfield.com/warranty Drop-in ice chest with cover Drop-in glass filler Regulatory Certifications N225-E Drop-In Freezer with Export Voltage... -
Page 5: Installation
Section 2 Installation Warning DANGER This equipment is intended for indoor use only. Do not Installation must comply with all applicable fire and install or operate this equipment in outdoor areas. health codes in your jurisdiction. Caution DANGER Do not position the air intake vent near steam or heat Use appropriate safety equipment during installation exhaust of another appliance. -
Page 6: Clearance Requirements
Installation Section 2 Clearance Requirements Dimensions Model Cabinet DANGER Capacity Minimum clearance requirements are the same for 20.25” 20.25” 23.25” 90lbs (51cm) (51cm) (59cm) (41kg) noncombustible locations as for combustible locations. 24” 21” 22.6” 45lbs The flooring under the appliance must be made of a (61cm) (53cm) (57cm) -
Page 7: Cutout Installation Dimension
Section 2 Installation Cutout Installation Dimension 240 Details Ice chest with cover, model 240 can be set on a counter Mounting Model Cutout Size or plate shelf. Select the desired location. Mark the drain Studs location and drill a 1.50” (4cm) diameter hole. 19.25”... -
Page 8: N225 & N227 Standard Installation Details
Installation Section 2 N225 & N227 STANDARD INSTALLATION DETAILS 3. Place the condensing unit through the counter cutout. For any non-standard installation consult the factory. 4. Extend the telescoping duct from the front of the condensing unit to the back of the louver. Export 1. -
Page 9: N225 & N227 Alternate Installation Details
Section 2 Installation N225 & N227 ALTERNATE INSTALLATION DETAILS 3. Louver cutout must extend to bottom of cabinet. NOTE: This installation is not recommended as it will limit NOTE: Any restriction to the proper air flow will void the access to the control. compressor warranty. -
Page 10: Electrical Service
Installation Section 2 Electrical Service RATED AMPERAGES, HORSEPOWER, VOLTAGE & POWER CORD CHART DANGER Model V/Hz/Ph H.P. Plug Check all wiring connections, including factory terminals, before operation. Connections can become 204P loose during shipment and installation. Warning N225-E 230-240/50/1 CEE 7/7 This appliance must be grounded and all field wiring N225P 115/60/1... -
Page 11: Refrigeration
Section 2 Installation Refrigeration Water Connection Warning Design System Evap BTU/ Model Charge Load BTU Cap. BTU TD/Temp Connect to a potable water supply only. All 1/2” (13mm) IPS water inlets must be field connected 204P following local code requirements. Drain N225-E 20/20°/-23°... - Page 12 Installation Section 2 THIS PAGE INTENTIONALLY LEFT BLANK Part Number: 9291456 11/17...
-
Page 13: Operation
Section 3 Operation 115Volt N225P & N227P Operation DANGER The models N225P and N227P are designed to hold The on-site supervisor is responsible for ensuring that refrigerated or frozen product. They are set at the factory at operators are made aware of the inherent dangers of a temperature range of -5°F to 5°F (-21°C to -15°C).Available operating this equipment. -
Page 14: Temperature Control & Display
Operation Section 3 TEMPERATURE CONTROL & DISPLAY Press upper or lower right button. • Display show actual set-point (blinking). • If buttons untouched for 3 seconds returns to normal. • Increase set-point by pressing upper button. Max value depends on parameters in control. •... -
Page 15: Changing Display From Fahrenheit To Celsius On Erc112 Control
Section 3 Operation CHANGING DISPLAY FROM FAHRENHEIT TO CELSIUS 6. -F should be displayed indicating Fahrenheit. Use ON ERC112 CONTROL the down arrow to change it to -C for Celsius and hit the stand-by button (lower left button) to enter the 1. -
Page 16: 230-240V Export N225-E & N227-E Operation
Operation Section 3 230-240V Export N225-E & N227-E Operation The models N225-E and N227-E are designed to hold frozen products at a temperature range of 5°F to -5°F (-15°C to -21°C). After installation, the unit will begin operating simply by plugging it into the proper outlet. If the unit does not operate after being plugged in, check to see if the thermostat is in the OFF position. -
Page 17: Maintenance
Section 4 Maintenance DANGER DANGER It is the responsibility of the equipment owner to Disconnect electric power at the main power disconnect perform a Personal Protective Equipment Hazard for all equipment being serviced. Observe correct Assessment to ensure adequate protection during polarity of incoming line voltage. -
Page 18: N225 & N227 Cleaning The Condenser Coil
Maintenance Section 4 Wipe surfaces with a damp cloth rinsed in water to remove N225 & N227 CLEANING THE CONDENSER COIL dust and dirt from the unit. Always rub with the “grain” of In order to maintain proper refrigeration performance, the the stainless steel to avoid marring the finish. - Page 20 DELFIELD 980 SOUTH ISABELLA ROAD, MOUNT PLEASANT, MI 48858 800-733-8821 WWW.DELFIELD.COM WWW.WELBILT.COM Welbilt provides the world’s top chefs, and premier chain operators or growing independents with industry leading equipment and solutions. Our cutting-edge designs and lean manufacturing tactics are powered by deep knowledge, operator insights, and culinary expertise.
Need help?
Do you have a question about the 200 Series and is the answer not in the manual?
Questions and answers