QUANTUM QVOIP SERIES MANUAL QUANTUM Q9000VOiP SERIES MANUAL Version 042018 TABLE OF CONTENTS Limitation of Liability Function Code 15: Initializing Event Recording Function Code 16: Auto Unlock Schedule (AUS) Products Limited Warranty Function Code 17: Time Zone (TMZ) Function Code 18: Holiday Zone (HLD)
Pach and Company is not liable for any errors that might occur from use of this document, nor is any commitment to update the information herein implied. Pach and Company does not assume any liability for any damages, which may arise in installation or use of the Quantum Q9000VOIP Series Pach and Company does not assume liability for any incompatibility between the Quantum Q9000VOIP Series and users devices.
Pach & Company thanks and congratulates you on the purchase of your Quantum Q9000VOIP Series Telephone Entry Access Control Systems. The manual is designed to guide you through the proper programming and use of the Quantum Q9000VOIP Series It is important for you to read and follow the manual completely.
QUANTUM QVOIP SERIES MANUAL 2-PIN GREEN TERMINAL BLOCK (2) QATA2 VOIP ANALOG TERMINAL ADAPTER FOR GOOGLE VOICE (1) QUICK GUIDE (1) CHAPTER 2 Installation and Wiring Diagram Follow the wiring diagram carefully. Improper installation will void the warranty. Please call technical support in case you have any difficulties during the installation.
Page 5
QUANTUM QVOIP SERIES MANUAL Figure 2.1 General Wiring Diagram 2.2 Power Wiring Diagram file:///C|/PACH-CO.COM-2020/online_manual/q9000voip_series_manual.htm[1/17/2020 10:02:05 AM]...
Page 6
Power Wiring Diagram 2.3 VOIP Telephone Wiring Diagram Compatibility issue may occur between the Quantum Q9000VOIP Series and your VOIP line. The Q9000VOIP Series can be connected to your analog dial tone without using our QATA2 as below file:///C|/PACH-CO.COM-2020/online_manual/q9000voip_series_manual.htm[1/17/2020 10:02:05 AM]...
Page 7
QUANTUM QVOIP SERIES MANUAL Figure 2.3 VOIP Wiring Diagram 2.4 Door Strike Wiring Diagram Figure 2.4 file:///C|/PACH-CO.COM-2020/online_manual/q9000voip_series_manual.htm[1/17/2020 10:02:05 AM]...
Page 8
QUANTUM QVOIP SERIES MANUAL Door Strike Wiring Diagram 2.5 Input Device and Door Sensor Wiring Diagram Figure 2.5 Input Device and Door Sensor Wiring Diagram 2.6 Satellite System Wiring Diagram file:///C|/PACH-CO.COM-2020/online_manual/q9000voip_series_manual.htm[1/17/2020 10:02:05 AM]...
QUANTUM QVOIP SERIES MANUAL Figure 2.6 Satellite System Wiring Diagram Assuming all wiring has been done properly according to chapter 2 then turn the system s power on as shown on figure 2.1 number 10. The LCD will go into a cycling mode as below LCD Display OK --- Flash OK --- RTC OK --- DTMF OK --- INIT START --- INIT COMPLTE --- SCROLLING CHAPTER 3...
QUANTUM QVOIP SERIES MANUAL Enter name up to 16 characters (name can be a person real name, apartment number, etc., directory will be sorted in alphabetical order) then press # Enter the tenant phone number up to 16-digit (phone number can be land line number, cellular number or Voice over IP (VOIP) number. Note: VOIP phones may have problems releasing door) then press #.
Page 12
QUANTUM QVOIP SERIES MANUAL if directory does not exist Function Code 04 - Clear All Tenant Directories Log-in to programming Enter 04 then # Do the following: - Press 1 (to clear all directories) then press # - Press * to cancel Function Code 05 - Call Forwarding Enable or disable call.
Page 13
QUANTUM QVOIP SERIES MANUAL Enter door 1 or 2, or 3 for both, then press # Enter time zone 1-3 then press # Enter 00 hours) - 20 see function code 17 then press # Enter satellite system ID 0-7 (enter 0 if no satellite connected to the QR5) then press # Enter...
Page 14
QUANTUM QVOIP SERIES MANUAL 1 to clear all access code then press # * to cancel Function Code 09 - Access Code Digit Log-in to programming Enter 09 then #| 3. Enter 4, 5, 6, 7 or 8 (default setting is 4 digit) then press # Function Code 10 - Add New Card Log-in to programming Enter 10 then #...
Page 15
QUANTUM QVOIP SERIES MANUAL Enter 0= no more additional time zone then press # and return to step 3 to add program another card 1= add additional time zone then press # and return to step 6 * = exit programming Function Code 11 - Delete Card Log-in to programming Enter 11 then #...
QUANTUM QVOIP SERIES MANUAL the press # Function Code 14 - Set Date Log-in to programming Enter 14 then # Enter YYYY/MM/DD YYYY= year MM= Month DD= Date then press # Enter 0= Sunday, 1= Monday, 2= Tuesday, 3= Wednesday, 4= Thursday, 5= Friday, 6= Saturday then press # 5.
QUANTUM QVOIP SERIES MANUAL Enter AUS (0-9) then press # Enter 0= Delete the existing AUS the press # 1= Add AUS then press # Enter open time in military then press # Enter close time in military then press # Enter 0= Sunday, 1= Monday, 2= Tuesday, 3= Wednesday, 4= Thursday, 5= Friday, 6= Saturday then press #...
QUANTUM QVOIP SERIES MANUAL 0= Delete the existing time zone then press # 1= add new time zone then press # Enter start time in military then press # Enter end time in military then press # Enter 0= Sunday, 1= Monday, 2= Tuesday, 3= Wednesday, 4= Thursday, 5= Friday, 6= Saturday then press # Return to step 3 to program more time zone Function Code 18 - Holiday Zone (HLD)
QUANTUM QVOIP SERIES MANUAL changed to 2,3 or 4 digit. It also uses to do direct call. Log-in to programming Enter 19 then # Enter 2, 3 or 4 digit then press # Function Code 20 - AUXIN1 AUXIN1 is used for input device such as postal lock, infrared sensor, exit button, etc..AUXIN1 is associated with relay 1 Log-in to programming Enter 20 then # 3.
QUANTUM QVOIP SERIES MANUAL Function Code 23 Lock-out Count The system will be disabled in about 60 seconds after pressing invalid access code or swiping invalid card as specified on the Lock-out Count. Log-in to programming 2. Enter 23 then # 3.
QUANTUM QVOIP SERIES MANUAL Function Code 27 Talk Time The amount of time the visitor can talk to the tenant. The timer starts as soon as the system is off-hook. Log-in to programming 2. Enter 27 then # 3. Enter 10-240 seconds then press # Function Code 28 Unlock Relay 1 Time The amount of time for relay 1 to trigger.
QUANTUM QVOIP SERIES MANUAL 4. Enter code number 01-10 then press # Enter 4-8 digit code, see digit setting on function code 09 Chapter 3 for keypad layout 6. Enter name then press # 7. Enter 1= relay 1(door 1), 2= relay 2 (door 2) or 3= both relay then press # 8.
QUANTUM QVOIP SERIES MANUAL 4. Enter code 01-10 then press # 5. Enter 4-8 digit code, see digit setting on function code 09 Chapter 3 for keypad layout 6. Enter name then press # 7. Enter 1= relay 1(door 1), 2= relay 2 (door 2) or 3= both relay then press # 8.
QUANTUM QVOIP SERIES MANUAL 5. Present the card or fob in front of the black window, the system will register the card or fob 8-digit number printed then press # Chapter 3 for keypad layout 6. Enter name and press # 7.
QUANTUM QVOIP SERIES MANUAL 5. Enter 4-8 digit code, see digit setting on function code 09 Chapter 3 for keypad layout 6. Present the card or fob in front of the black window, the system will register the card or fob 8-digit number printed then press # 7.
QUANTUM QVOIP SERIES MANUAL Log-in to programming 2. Enter 39 then # 3. Press 0= disable remote access 1= enable remote access (default) then press # Function Code 40 DTMF Relay 1 By default the DTMF remote opening relay 1 (door 1) key number is set to 9 means pressing 9 will remotely trigger relay 1 (door 1). The number can be changed by selecting 1-9 to trigger relay 1 (door 1).
QUANTUM QVOIP SERIES MANUAL 3. Enter 1= door control, 2=trigger simultaneously as relay 1, 3= alarm mode (see function code 24), 4= turn relay 2 on/off remotely (DTMF key 7/6), then press # Function Code 43 Do Not Disturb Time Zone If you do not want to be disturbed from someone calling you from the system during certain hours of the days, you can create Do Not Disturb Time Zone.
QUANTUM QVOIP SERIES MANUAL Enter 0= Delete the existing time zone then press # 1= add new time zone then press # Enter start time in military then press # Enter end time in military then press # Enter 0= Sunday, 1= Monday, 2= Tuesday, 3= Wednesday, 4= Thursday, 5= Friday, 6= Saturday then press # Return to step 3 to program more time zone Function Code 45 Relay 1 and 2 Unlock Timer...
QUANTUM QVOIP SERIES MANUAL Function Code 48 PBX Enable If the system is installed behind a Private Branch Exchange (PBX) then 9 is necessary before dialing an outside line. If this function is enabled then the system can only be dialing an outside line, it cannot dial the extension. Log-in to programming 2.
Page 30
5.4 Opening Door Using Card, Temporary Card, and Special Card The Quantum Q9000VOIP Series has built-in card reader. The door can be access using UFOB, UCLAM or UISO. Card Standard Operation is used to open the door and door will be closed automatically, see...
Page 31
QUANTUM QVOIP SERIES MANUAL 5.5 Extending Talk Time The talk time timer is set on function code 27. The warning beep will be heard one minute before the talk time is expired. It can be extended more another full cycle by pressing # 5.6 Call the System from Remote Location The system must be install in Intercom and Call Forwarding Mode Wiring Diagram...