Advertisement
Other settings
LED display on/off ()
To set the control panel's LED display to be on all the time, or to
automatically sleep when not in use:
1.
Select
in the control menu and press ENTER.
2.
Select
and press ENTER.
3.
Select
(display on) or
(display off when not in use).
4.
Press ENTER to save your selection.
LCD display inversion ()
To invert the control panel's LED display for easier reading:
1.
Select
in the control menu and press ENTER.
2.
Select
and press ENTER.
Select to invert the display.
3.
4.
Press ENTER to save your selection or MENU to escape.
Manual mode ()
Effects can be set from the control panel. To keep the effect
settings, do not exit the menu.
See the 9-channel mode DMX table for command values. To set
effects from the control panel:
1.
Enter the control menu and scroll to
. Press ENTER.
2.
Scroll to the color or effect to adjust. Press ENTER.
Press ▼ or ▲ to specify a value from 0 to 255 for the effect.
3.
4.
Press ENTER to set the effect.
5.
Press MENU and repeat for the other colors or effects.
Auto test ()
To test all of the fixture functions select and press ENTER.
Press MENU to exit the test routine.
Fixture readouts
Hours: To display the fixture's total operating hours select
and press ENTER. Press MENU to exit.
Firmware: To display the firmware version number, select
and press ENTER. Press MENU to exit.
Settings reset
To return all user settings to the factory default values, select
in the control menu. Press ENTER to confirm or MENU to
escape.
Remote control operation
The remote control works with all Compact PAR 64 LED fixtures
within range.
To operate the Compact PAR 64 LED with the remote control:
1.
Verify that the fixture is not connected to a DMX controller.
2.
Press MENU to enter the control menu.
3.
Scroll to
and press ENTER.
4.
Select
and press ENTER.
5.
Select
to disable Show Mode. Press ENTER.
6.
To execute commands, point the remote control towards the
front of the fixture and the press corresponding button. See
table below.
Remote Control Commands
Button
Function
BL
Toggle LEDs on/off
SP
Adjust speed (4 levels). Use with JU, FA, and SU.
Dimming (4 levels)
FL
Strobe (4 speeds)
R
Adjust Red intensity (off, 4 levels)
G
Adjust Green intensity (off, 4 levels)
B
Adjust Blue intensity (off, 4 levels)
W
Adjust White intensity (off, 4 levels)
A
Adjust Amber intensity (off, 4 levels)
UV
Adjust UV intensity (off, 4 levels)
Jump Mode – snaps thru pre-programmed colors.
JU
Adjust speed with SP.
Fade Mode – Fades thru pre-programmed colors.
FA
Adjust speed with SP.
AU
Auto-trigger mode.
Music-triggered Sound Mode. Adjust sensitivity level
SU
with SP.
CM+
Next color
CM-
Previous color
Replacing the wireless remote control battery
The wireless remote control uses a single CR 2025
coin/button/cell 3 V lithium battery. To replace the battery:
1.
Depress the battery tray lock on the reverse of the remote
control and slide out the battery tray. Remove the old battery.
2.
Insert a fresh battery with the positive terminal towards the
back of the remote. A diagram on the remote control
indicates the correct orientation.
3.
Align the battery tray to the remote control and re-insert the
tray ensuring that the locking mechanism is secure.
4.
Dispose of used batteries in accordance with local regulations.
If the coin/button/cell battery compartment does not close securely, stop
using the product and keep away from children and animals. Contact
Martin Professional for service and support.
Troubleshooting
Symptom
Potential Causes
Remedies
Ensure that the mains
supply is connected
and supplying power
Power supply issue
to the fixture
No light from
such as blown fuse,
Check all power
fixture, control
faulty connector or
connections and
panel dead
damaged cable
cables
Check and if
necessary replace the
fuse
Ensure that fixture's
DMX address
matches address set
on DMX control
device
Check DMX cables
Fault in the DMX
and connections
network due to
Fixture does not
Ensure that DMX link
connector or cable
is terminated
respond to DMX
damage, incorrect
control
Reduce number of
DMX addressing, or
fixtures on DMX link
signal interference
Attempt to control the
fixture with another
DMX control device
Move or shield link if it
is close to unshielded
high-voltage cables
Fixture set to run as
Change master/slave
slave
setting master
Sound trigger
Enable sound trigger
disabled
Fixture does not
Change DMX state
respond in Show
Show Mode disabled
setting to Show Mode
Mode
or no show selected
Select a show
Increase sensitivity
Microphone
sensitivity too low
Disconnect or turn off
Fixture receiving
DMX controller
Fixtures don't
multiple control
Verify there is only
respond in
signals
one fixture master
master/slave
fixture
mode
Set first fixture in
No master fixture
chain as master
Remote control out of
Move closer to fixture
range
Fixture does not
respond to remote
Battery exhausted
Replace battery
control
Incorrect menu
Verify show mode is
disabled (- = )
settings
Information
subject
to
change
without
notice.
HARMAN
Professional Denmark ApS disclaims liability for any injury,
damage, direct or indirect loss, consequential or economic loss or
any other loss occasioned by the use of, inability to use or reliance
on the information contained in this document.
©2017
HARMAN
Professional
Denmark
ApS.
All
®
reserved. Martin
is a registered trademark of HARMAN Professional
Denmark
ApS
registered
in
the
United
States
and
countries. Features, specifications, and appearance are subject to
change without notice.
HARMAN Professional Denmark ApS
Olof Palmes Allé 18 • 8200 Aarhus N • Denmark
www.martin.com
Document revision: A
rights
other
Advertisement
