Dmx Linking; Dmx Personalities; Wireless Operation; Initial Setup - Chauvet WELL Fit User Manual

Setup

DMX Linking

DMX
Personalities
Wireless
Operation

Initial Setup

Configuration

Product Pairing

Storage Notes

-8-
The WELL Fit will work with a DMX controller using a wireless DMX connection. If using other
DMX-compatible products with the WELL Fit, you can control each individually with a single
DMX controller.
The WELL Fit uses a wireless DMX data connection for the 4 Ch, 6 Ch, 10Ch, HSI and HSV

DMX personalities.

·
Refer to the Introduction
·
Refer to the Operation
personalities.
·
The DMX Values section provides you with detailed information regarding the DMX
personalities.
If you are not familiar with or need more information about DMX standards, Master/Slave
connectivity, or the DMX cables needed to link this product to a DMX controller,
download the DMX Primer from the Chauvet website: www.chauvetprofessional.com.
In optimal conditions, the WELL Fit can operate up to 300 m (900 ft) away from the W-DMX
transmitter. The W-DMX receiver in the WELL Fit must be paired with the W-DMX transmitter
for wireless operation.
Once a WDMX receiver has been linked to a specific WDMX transmitter, it will remain
linked to that specific transmitter until it is linked to a different one.
1. Turn the W-DMX transmitter on.
2. Connect the W-DMX transmitter to a DMX controller.
3. Place the WELL Fit within 300 m from the W-DMX transmitter.
4. Disconnect any DMX cable from the WELL Fit.
5. Turn the WELL Fit on.
1. From the WELL Fit's control panel, go to DMX Address.
2. Select the start address, as with any other DMX compatible product.
3. Go to Wireless Setting > Receive.
4. Select On. (The Signal Strength Indicator will show a ? in front of the bars)
5. Press the reset button on the W-DMX transmitter. (The Signal Strength Indicator on the
WELL Fit will show a ϟ in front of the bars for 3 seconds while a connection is established.)
If the WELL Fit has already been paired with the W-DMX transmitter, the Signal Strength
Indicator in the middle of the LCD screen will show the strength of the signal. In this case, the
WELL Fit is ready to work in Wireless mode.
Pairing the WELL Fit and a new W-DMX transmitter:
1. From the WELL Fit's control panel, go to Wireless Setting.
2. Select Reset. The Signal Strength Indicator on the WELL Fit will show a ? in front of the
bars.
3. From the W-DMX transmitter, press <RESET> (the Signal Indicator on the transmitter will
flash).
4. Once the transmitter has found the WELL Fit, the Signal indicator on the W-DMX
transmitter will illuminate solid.
5. The Signal Strength Indicator in the middle of the LCD screen on the WELL Fit will show the
strength of the signal.
·
Store charged product(s) in a dry environment, away from direct sunlight.
·
Charge or discharge the battery to approximately 50% of capacity before storage.
·
Lithium-Ion batteries continue to slowly discharge (self-discharge) when not in use or while
in storage. Routinely check the battery's charge status
·
Store the battery at temperatures between 41 °F and 68 °F (5 °C and 20 °C).
· Always store the product in an upright position (≤ 10° tilt).
W-DMX operation can be interrupted or inhibited by liquid masses between the
transmitter and receiver such as water, snow, or people. For best results, keep the area
between the transmitter and receiver clear of any liquid mass.
chapter for a brief description of each DMX personality.
chapter to learn how to configure the WELL Fit to work in these
WELL Fit User Manual Rev. 5