Table of Contents
Advertisement
Installation Instructions
Installing the RF Receiver
Use any ADEMCO 5800 Series Wireless Receivers, such
as:
RF Receiver
5881L/5882L
5881M/5882M
5881H/5882H,
5883, FA260RF FA148CP = up to 26 plus 8 buttons
1. Set Device Address to "00" as described in its
instructions (set all switches to the right, "off" position).
2. Mount the receiver, noting that the RF receiver can
detect signals from transmitters within a nominal
range of 200 feet.
3. Connect the receiver's wire harness to the control's
keypad terminals. Plug the connector at the other end
of the harness into the receiver. Refer to the
installation instructions provided with the receiver
for further installation procedures regarding antenna
mounting, etc.
NOTE
CIRCUIT BOARD IS MOUNTED IN
CONTROL'S CABINET. GROUNDING
LUGS (2) PROVIDED MUST BE INSERTED
IN LEFT-HAND TERMINALS OF ANTENNA
BLOCKS AND SECURED TO CABINET.
(SEE RECEIVER'S AND CONTROL'S
INSTRUCTIONS)
MOUNTING
HOLES
Figure 9. 5881/5882 RF Receiver (cover removed)
Installing a 5800TM Module
1. Mount the 5800TM next to the RF receiver (between
one and two feet from the receiver's antennas) using
its accompanying mounting bracket. Do not install
within the control cabinet.
2. Connect the 5800TM to the control panel's keypad
connection terminals as shown on the Summary of
Connections diagram and set to address 28.
Installing the Transmitters
1. To be sure reception of the transmitter's signal at the
proposed mounting location is adequate, perform a
Go/No Go Test, described in the Testing the System
section.
2. Install transmitters in accordance with the
instructions provided with each.
3. Set 5827, 5827BD, 5804BD wireless keypads to the
programmed House ID (field *24), using its DIP
switches (5827) or follow the instructions provided
with the device.
ULC NOTE: In accordance with ULC standards, the
RF supervision period for the FA168CPS-CN and
FA148CP-CN is three hours for Fire zones (Zone Type 9
and 16) and 12 hours for all other zone types.
2-8
No. of Zones
up to 8
up to 16
FA168CPS = up to 40 plus 16 buttons
ANTENNAS
(INSERT IN
RIGHT-HAND
TERMINALS)
INSERT IN
RIGHT- HAND
TERMINALS
YELLOW
RED
MODEL NO. IS INDICATED ON CIRCUIT BOARD
BLACK
GREEN
5882
DIP
LOCATION
SWITCH
INTERFERENCE
INDICATOR
LED
CIRCUIT BOARD
PLUG
SOCKET
TO RELEASE CIRCUIT BOARD,
REMOVE SCREWS AND
BEND BACK TABS
Notes
• The receiver is supervised and a trouble report is
sent ("CHECK 100" displayed) if communication
between the panel and receiver is interrupted, or if
no valid RF signals from at least one supervised
transmitter are received within 12 hours.
If the receiver is mounted remotely:
• Place the RF receiver in a high, centrally located
area for best reception.
• Do not locate the receiver or transmitters on or
near metal objects. This will decrease range
and/or block transmissions.
• Do not locate the RF receiver in an area of high
RF interference (indicated by frequent or
prolonged lighting of the LED in the receiver;
random flicker is OK).
• Do not locate RF receiver closer than 10 feet from
any keypads to avoid interference from the
microprocessors in those units.
WIRELESS ZONE NUMBERS
FA168CPS: transmitter zones 9-48
TO CONTROL'S
REMOTE KEYPAD
CONNECTION
POINTS.
WIRING OPENING
FA148CP:
KNOCKOUT AREA
FOR SURFACE WIRING
5881-003-V0
Notes
• Use this module only if you are using one or more
wireless bi-directional keypads or keyfobs with a
wireless Receiver; 5800TM is not necessary if
using a Transceiver (e.g., 5883).
• The 5800TM must be set to address 28 (cut red-
W1 jumper).
• The 5800TM can be used in partition 1 only.
• For additional information regarding the
5800TM, refer to the 5800TM's instructions.
Notes
• Refer to the table of compatible devices at the
back of this manual.
• Supervised transmitters
the receiver at 70-90 minute intervals. If at least
one check-in message is not received from each
transmitter within a 12-hour period, the "missing"
transmitter number(s) and "CHECK" is displayed.
†
Hand-held transmitters (e.g., 5802, 5802CP, 5804,
5804BD, 5827, 5827BD) do not send check-in signals.
U L
The following transmitters are not intended for use
in UL installations: 5802MN, 5802MN2, 5804, 5804BD,
5814, 5816TEMP, 5819, 5819WHS & BRS, and 5850.
The 5827BD and 5800TM can be used in UL Listed
Residential Burglar installations.
button zones 49-64
transmitter zones 9-34
button zones 49-56
†
send check-in signals to
Advertisement
Table of Contents
