TDK-Lambda GEN 8-400 ABCDE User Manual page 6

3.8.1. GENERAL ...............................................................................................................................................36
3.8.2. PRIOR TO OPERATION.........................................................................................................................36
3.8.3. CONSTANT VOLTAGE CHECK.............................................................................................................36
3.8.4. CONSTANT CURRENT CHECK ............................................................................................................37
3.8.5. OVP CHECK ...........................................................................................................................................37
3.8.6. UVL CHECK............................................................................................................................................37
3.8.7. FOLDBACK CHECK ...............................................................................................................................38
3.8.8. ADDRESS SETTING ..............................................................................................................................38
3.8.9. BAUD RATE SETTING (RS-232 AND RS-485 ONLY)...........................................................................38
3.9.CONNECTING THE LOAD ................................................................................................................................38
3.9.1. LOAD WIRING ........................................................................................................................................38
3.9.2. CURRENT CARRYING CAPACITY........................................................................................................39
3.9.3. WIRE TERMINATION .............................................................................................................................39
3.9.4. NOISE AND IMPEDANCE EFFECTS.....................................................................................................40
3.9.5. INDUCTIVE LOADS................................................................................................................................40
3.9.6. MAKING THE LOAD CONNECTIONS ...................................................................................................40
3.9.7. CONNECTING SINGLE LOADS, LOCAL SENSING (DEFAULT). ........................................................43
3.9.8. CONNECTING SINGLE LOADS, REMOTE SENSING..........................................................................43
3.9.9. CONNECTING MULTIPLE LOADS, RADIAL DISTRIBUTION METHOD..............................................43
3.9.10.MULTIPLE LOAD CONNECTION WITH DISTRIBUTION TERMINALS................................................44
3.9.11.GROUNDING OUTPUTS .......................................................................................................................44
3.10.LOCAL AND REMOTE SENSING ...................................................................................................................45
3.10.1.SENSE WIRING......................................................................................................................................45
3.10.2.LOCAL SENSING ...................................................................................................................................45
3.10.3.REMOTE SENSING ...............................................................................................................................46
3.10.4.J2 SENSE CONNECTOR TECHNICAL INFORMATION .......................................................................46
3.11.REPACKAGING FOR SHIPMENT ...................................................................................................................46
4.FRONT AND REAR PANEL CONTROLS AND CONNECTORS ........................................................................47
4.1.INTRODUCTION ................................................................................................................................................47
4.2.FRONT PANEL CONTROLS AND INDICATORS .............................................................................................47
4.3.REAR PANEL CONNECTIONS AND CONTROLS ...........................................................................................49
4.4.REAR PANEL SW1 SETUP SWITCH................................................................................................................50
4.4.1. SW1 POSITION FUNCTION...................................................................................................................51
4.4.2. RESETTING THE SW1 SWITCH ...........................................................................................................51
4.5.REAR PANEL J1 PROGRAMMING AND MONITORING CONNECTOR .........................................................52
4.5.1. MAKING J1 CONNECTIONS..................................................................................................................52
5.LOCAL OPERATION ............................................................................................................................................54
5.1.INTRODUCTION ................................................................................................................................................54
5.2.STANDARD OPERATION..................................................................................................................................54
5.2.1. CONSTANT VOLTAGE MODE...............................................................................................................54
5.2.2. CONSTANT CURRENT MODE ..............................................................................................................55
5.2.3. AUTOMATIC CROSSOVER ...................................................................................................................55
5.3.OVER VOLTAGE PROTECTION (OVP)............................................................................................................55
5.3.1. SETTING THE OVP LEVEL....................................................................................................................55
5.3.2. ACTIVATED OVP PROTECTION INDICATIONS ..................................................................................56
5.3.3. RESETTING THE OVP CIRCUIT ...........................................................................................................56
5.4.UNDER VOLTAGE LIMIT (UVL) ........................................................................................................................56
5.4.1. SETTING THE UVL LEVEL ....................................................................................................................56
5.5.FOLDBACK PROTECTION................................................................................................................................56
5.5.1. SETTING THE FOLDBACK PROTECTION ...........................................................................................56
5.5.2. RESETTING ACTIVATED FOLDBACK PROTECTION .........................................................................57
5.6.OUTPUT ON/OFF CONTROL............................................................................................................................57
5.7.OUTPUT SHUT-OFF (SO) CONTROL VIA REAR PANEL J1 CONNECTOR ..................................................57
5.8.ENABLE/DISABLE CONTROL VIA REAR PANEL J1 CONNECTOR...............................................................58
5.9.CV/CC SIGNAL ..................................................................................................................................................58
5.10.PS_OK SIGNAL ...............................................................................................................................................58
5.11.SAFE-START AND AUTO-RESTART MODES ...............................................................................................59
5.11.1.AUTO-RESTART MODE ........................................................................................................................59
2
83503001 Rev G