TDK-LAMBDA GEN 40-85ABCDE Manuals

Manuals and User Guides for TDK-LAMBDA GEN 40-85ABCDE. We have 1 TDK-LAMBDA GEN 40-85ABCDE manual available for free PDF download: User Manual

TDK-Lambda GEN 40-85ABCDE User Manual

TDK-Lambda GEN 40-85ABCDE User Manual (96 pages)

2U GENESYS 3.3kW Programmable DC Power Supplies GEN 3300W series

Brand: TDK-Lambda | Category: Power Supply | Size: 2 MB

Table of Contents

Table of Contents
5
Warranty
9
English Safety Instructions
10
Francais (French)
13
Deutsch (German)
16
Italiano (Italian)
19
Portuges (Portugese)
22
Español (Spanish)
25
1 General Information

28
- User Manual Content
  28
- Introduction
  28
- Accessories
  30
  - General
    30
  - Serial Link Cable
    30
  - Misc. Hardware
    30
  - Ac Cables
    30
2 Specifications

32
- Output Rating
  32
- Input Characteristics
  32
- Constant Voltage Mode
  32
- Constant Current Mode
  32
- Analog Programming and Monitoring
  32
- Programming and Readback (Rs232/485, Optional Ieee Interface)
  32
- Protective Functions
  33
- Front Panel
  33
- Environmental Conditions
  33
- Mechanical
  33
- Safety/Emc
  33
- Supplemental Characteristics
  34
3 Installation

36
- General
  36
- Preparation for Use
  36
- Initial Inspections
  37
- Rack Mounting
  37
- Location, Mounting and Cooling
  38
- Ac Source Requirements
  38
- Ac Input Power Connection
  38
  - Ac Input Connector
    38
  - Ac Input Cord
    39
  - Ac Input Wire Connection
    39
- Turn-On Checkout Procedure
  40
  - General
    40
  - Prior to Operation
    40
  - Constant Voltage Check
    40
  - Constant Current Check
    41
  - Ovp Check
    41
  - Uvl Check
    41
  - Foldback Check
    42
  - Address Setting
    42
  - Baud Rate Setting (Rs-232 and Rs-485 Only)
    42
- Connecting the Load
  42
- Local and Remote Sensing
  49
  - Sense Wiring
    49
  - Local Sensing
    49
  - Remote Sensing
    50
  - J2 Sense Connector Technical Information
    50
- Repackaging for Shipment
  50
4 Front and Rear Panel Controls and Connectors

51
5 Local Operation

58
- Introduction
  58
- Standard Operation
  58
  - Constant Voltage Mode
    58
  - Constant Current Mode
    59
  - Automatic Crossover
    59
- Over Voltage Protection (Ovp)
  59
- Under Voltage Limit (Uvl)
  60
  - Setting the Uvl Level
    60
- Foldback Protection
  60
  - Setting the Foldback Protection
    60
  - Resetting Activated Foldback Protection
    61
- Output On/Off Control
  61
- Output Shut-Off (So) Control Via Rear Panel J1 Connector
  61
- Enable/Disable Control Via Rear Panel J1 Connector
  62
- CV/CC Signal
  62
- Ps_Ok Signal
  62
- Safe-Start and Auto-Restart Modes
  63
  - Auto-Restart Mode
    63
  - Safe-Start Mode
    63
  - Over Temperature Protection (Otp)
    63
- Last Setting Memory
  63
- Series Operation
  64
  - Series Connection for Increased Output Voltage
    64
  - Series Connection for Positive and Negative Output Voltage
    65
- Parallel Operation
  66
  - Basic Parallel Operation
    66
    
    1.Setting up the Master Unit
    66
    
    2.Setting up the Slave Units
    66
    
    3.Daisy Chain Connection: (See Fig. 5-6)
    67
    
    4.Setting over Voltage Protection
    67
    
    5.Setting Foldback Protection
    67
    
    6.Connection to the Load
    67
  - Advanced Parallel Operation
    67
    
    1.Advanced Parallel Configuration
    68
    
    2.Connection to the Load
    68
    
    3.Setting the Units as Master or Slave
    68
    
    4.Master and Slave Units Default Operation
    68
    
    5.Current Display Accuracy
    69
    
    6.To Release Units from Slave Mode
    69
- Daisy-Chain Connection
  70
- Front Panel Locking
  71
  - Unlocked Front Panel
    71
  - Locked Front Panel
    71
6 Remote Analog Programming

72
7 Rs232 & Rs485 Remote Control

76
- Introduction
  76
- Configuration
  76
  - Default Setting
    76
  - Address Setting
    76
  - Rs232 or Rs485 Selection
    76
  - Baud Rate Setting
    76
  - Setting the Unit into Remote or Local Mode
    76
  - Rs232/Rs485 Port in Local Mode
    77
  - Front Panel in Remote Mode
    77
- Rear Panel Rs232/Rs485 Connector
  77
- Connecting Power Supplies to Rs232 or Rs485 Bus
  78
  - Single Power Supply
    78
  - Multi Power Supply Connection to Rs232 or Rs485 Bus
    79
- Communication Interface Protocol
  79
  - Data Format
    79
  - Addressing
    79
  - End of Message
    79
  - Command Repeat
    80
  - Checksum
    80
  - Acknowledge
    80
  - Error Message
    80
  - Backspace
    80
- Error Messages
  80
- Command Set Description
  80
  - General Guide
    80
  - Command Set Categories
    81
  - Initialization Control Commands
    81
  - ID Control Commands
    81
  - Output Control Commands
    81
- Global Output Commands
  83
  - Description
    83
- Fast Queries
  84
  - Fast Test for Connection
    84
  - Fast Read Registers
    85
  - Read Power-On Time
    85
  - Service Request Messages
    86
- Status and Error Commands
  86
- Status, Error, and Srq Registers
  87
  - General Description
    87
  - Conditional Registers
    88
  - Service Request: Enable and Event Registers
    89
    
    1.Fault Enable Register
    89
    
    2.Fault Event Register
    89
    
    3.Status Enable Register
    90
    
    4.Status Event Register
    90
- Serial Communication Test Set-Up
  91
  - Equipment
    91
  - Pc Set-Up
    91
  - Power Supply Set-Up
    91
  - Communication Test
    91
8 Isolated Analog Programming Option

92
9 Maintenance

95
- Introduction
  95
- Units under Warranty
  95
- Periodic Maintenance
  95
- Adjustments and Calibration
  95
- Parts Replacement and Repairs
  95
- Troubleshooting
  95
- Fuse Rating
  96

Advertisement

Advertisement

Related Products

TDK-LAMBDA Categories

Power Supply

Power Supply Media Converter Cables and connectors Racks & Stands Portable Generator

More TDK-LAMBDA Manuals