Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Planika Galio GAS-60-023
Summary of Contents for Planika Galio GAS-60-023
- Page 1 INSTALLATION MANUAL Galio Insert Manual G20/G25 (Natural Gas) G30/G31 (Propane-Butane/Propane) [mm] 1160 1132 Manufactured by Planika Sp. z o.o. Bydgoska 38 86-061 Brzoza Poland Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02 29.06.2020...
-
Page 2: Table Of Contents
Checking the flame appearance........................17 MAINTENANCE AND UPKEEP ..........................18 8.1. Testing and cleaning ............................18 8.2. Glass cleaning ..............................18 TROUBLESHOOTING ..............................18 TECHNICAL SPECIFICATION ..........................19 MANUFACTURER’S CONTACT DETAILS ....................... 19 Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02 29.06.2020... -
Page 3: Introduction
In case of noticing any sort of gas leaks the fireplace as well as the main valve of the gas cylinder need to be • turned off. After use turn off the gas cylinder valve. • Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02 29.06.2020... -
Page 4: Safety Instruction Regarding The Use Of The Gas Cylinder
4x bag of decorative stones • 1x 4 metre rubber gas linkage – installed (only LPG version) • 1x pressure regulator (37mbar) – installed (only LPG version) • 1x installation manual • 1x user’s manual • Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02 29.06.2020... -
Page 5: Unboxing And Installation
10 cm (Photo 2). Photo 2 If all the points were completed according to the instruction the gas cylinder can be • now connected. Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02 29.06.2020... -
Page 6: Montage
Additionally, Planika materials doesn't recommend placing heat-sensitive objects above the fireplace as it may shorten their lifetime. Planika will not be responsible for any damage caused by high temperature affecting objects installed above the fire. Ventilation grate or slot with ventilation... -
Page 7: Directions Of How To Design A Housing For The Fireplace
Level the plane of the cavity. The level deviation must not exceed 2 mm Ventilation grate or slot with ventilation area of minimum 150cm2 Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02 29.06.2020... -
Page 8: Possible Housing Variants
WARNING! It is crucial to manufacture a slot in the side of the housing where the insert is placed for the gas linkage and the pressure regulator (only in case of LPG version). Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02... - Page 9 • If in future a need arises of having to take the insert out of the housing it may only be done when the device is turned off and cooled down and the valve on the gas cylinder is closed. • Keep this instruction manual for the lifetime of the device. Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02...
-
Page 10: Installation Of The Gas Linkage
Quick-release: For this type of connection no tool is required. On/off regulation of gas connection is made • through a switch on the regulator or on a special connector. In case of using a connector with a thread Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02... - Page 11 4. To let the gas flow in turn the switch into the ON the bottle counter-clockwise. position (or into the flame image). Place the gas cylinder in a correct distance from the fireplace (min 1,5 metres away). • Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02 29.06.2020...
- Page 12 REPLACE the linkage closer or cap on the REPLACE the tightening cap on an empty or empty or partially full bottle if it’s not being partially full bottle if it’s not being used. used. Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02 29.06.2020...
-
Page 13: Pressure Regulator Replacement (Lpg Version)
(philips) or a flat wrench. Move the clamp away from the stub of gas regulator. 6. Take off the linkage from the stub of regulator. 7. Attach a new linkage on the stub of regulator. Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02 29.06.2020... -
Page 14: Operating Instructions
(Photo 3). Photo 3 6.1. Start-up of the device Make sure that the knob is placed in „OFF” position (all the way clockwise) (Photo 4). • Photo 4 Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02 29.06.2020... -
Page 15: Regulation Of The Flame Size
• clockwise or counter-clockwise. To achieve a higher flame turn the know clockwise to “Hi” position. To achieve a lower flame turn the knob • counter- clockwise to “Lo” position (Photo 7). Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02 29.06.2020... -
Page 16: Device Shutdown
The battery is placed in the container located on the control pane next to the flame regulation knob Unscrew the ignition button • Remove the battery and place the new one into the container. WARNING! Remember about proper • polarization of the battery. Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02 29.06.2020... -
Page 17: Testing
Remember not to cover the cover, which houses the ignition and the pilot flame, with stones. WARNING!!! • Turn on the fireplace and check the appearance of the flame once again. • Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02 29.06.2020... -
Page 18: Maintenance And Upkeep
The cylinder valve has opened rapidly. regulator. A vivid/ bright orange and smoky Holes blocked in the apparatus producing the Unmount the burner and clean/ unblock the flame of the burner. gas and air mixture. apparatus’ holes. Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02 29.06.2020... -
Page 19: Technical Specification
Safety device Gas control valve BS190 Flexible hose (4 m) Ø9mm MANUFACTURER’S CONTACT DETAILS Manufacturer: Planika Sp. z o.o. Address: Bydgoska 38 86-061 Brzoza Poland Telephone: + 48 52 364 11 60 Copyright Planika Sp. z o.o. www.planikafires.com IG0265#02 29.06.2020...
Need help?
Do you have a question about the Galio GAS-60-023 and is the answer not in the manual?
Questions and answers