Advanced Programming; Wiring Diagram; Monitor Settings - golmar Tekna-S Gtwin Quick Manual

ADVANCED PROGRAMMING

Continued from previous page
- Exiting programming mode:
To exit 'programming mode,' press button
1 short and 2 long audible tones will confirm this and the status LED will
turn off, indicating that button can be released.
Note: When exiting programming mode, if 'doctor mode' has been activated, the
monitor's status LED will blink (green), see p.1.

MONITOR SETTINGS

SW1 configuration switch:
DIP switch 1: Must be OFF.
DIP switches 2 to 8: To configure the desired code (2 = most
significant bit and 8 = least significant bit).
Below is an example of a site with 22 apartments:
EL632/GTWIN
Code Monitor
/telephone
ON
C.126
C. 00
1 2 3 4 5 6 7 8
ON
C. 10 C. 09
1 2 3 4 5 6 7 8
ON
C. 08 C. 07
1 2 3 4 5 6 7 8
EL60 D 6
ON
C. 06 C. 05
1 2 3 4 5 6 7 8
ON
C. 04 C. 03
1 2 3 4 5 6 7 8
ON
C. 02 C. 01
1 2 3 4 5 6 7 8
EL610D
ON
C. 20 C. 19
1 2 3 4 5 6 7 8
ON
C. 18 C. 17
1 2 3 4 5 6 7 8
ON
C. 16 C. 15
1 2 3 4 5 6 7 8
ON
C. 14 C. 13
1 2 3 4 5 6 7 8
ON
C. 12 C. 1
1 2 3 4 5 6 7 8
SW2 configuration switch:
INT: Define the internal code of the monitor/telephone in order to set it as master,
slave 1, slave 2 or slave 3 using the SW2 switch with a code from 0 to 3 respectively.
ON ON ON
1 2 1 2 1 2
( )
*
( ) Factory setting. INT 0 INT 1 INT 2
*
I mportant: For optional programming, optional connections and more
information, see the TTEKNA S GTWIN manual (code 50120265).
https://doc.golmar.es/search/manual/ 5012 0265

WIRING DIAGRAM

4
O
ne building with 1 column of up to 127 monitors and 1 main video
panel (buttons).
for more than 5 seconds,
J2
MASTER
F. Line
MONITOR
ON (Z)
SW2
ON
1 2
INT 0
J2
MASTER
F. Line
MONITOR
ON (Z)
SW2
ON
1 2
INT 0
SW1 SW2
1 2 3 4 5 6 7 8 9 10 1 2
J2
MASTER
F. Line
MONITOR
ON (Z)
SW2
ON
1 2
INT 0
J2
MASTER
F. Line
MONITOR
Code Monitor
ON (Z)
SW2
/telephone
ON
ON
1 2
1 2 3 4 5 6 7 8 INT 0
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
Remove the jumper from all of the
( )
*
ON
distributors except the last.
1 2 3 4 5 6 7 8
1 ( ) To configure the SAV-GTWIN call
ON
repeater, see the TTEKNA-S GTWIN
1 2 3 4 5 6 7 8
manual, p. 16.
ON
( )
2 To connect
1 2 3 4 5 6 7 8
supply to
protector, see the TGTWIN SYSTEM
ON
MANUAL, p. 44.
1 2 3 4 5 6 7 8 ( )
3 To connect the secondary AC lock
ON release (Golmar), see the TGTWIN
SYSTEM MANUAL, p. 45.
1 2 3 4 5 6 7 8
Main panel
ON
Video door
entry system
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
ON
1
1 2 3 4 5 6 7 8
( ) SE2
3
Lock release
ON
max 12 Vdc/270 mA.
Remember: Button panel up to 122 apartments.
1 2
Important: For further information about the door panel, sections, distances,
INT 3
other wiring diagrams, etc., see the TGTWIN SYSTEM MANUAL,
code 50122345).
https://doc.golmar.es/search/manual/5012
COLUMN
D4L-GTWIN
DISTRIBUTOR
LINE OUT
LINE LINE
LINE IN LINE IN
3 4
LINE OUT Apartment Apartment LINE OUT
( ) Z=ON
CP front *
front CP
door call door call
S+
S+
S- S-
LINE LINE
LINE IN
LINE IN
1 2
Apartment
LINE OUT
Apartment LINE OUT
LINE IN
CP
front
front
CP
door call
S+ door call
S+
S-
S-
TO THE FOLLOWING DISTRIBUTORS
D4L-GTWIN
DISTRIBUTOR
LINE OUT
LINE LINE
LINE IN LINE IN
3 4
LINE OUT Apartment LINE OUT
Apartment
Z=OFF
CP front
front CP
door call
door call
S+
S+
S- S-
LINE LINE
LINE IN
LINE IN
1 2
LINE OUT Apartment
LINE OUT
LINE IN Apartment
CP front
front CP
door call
S+ door call
S+
S-
S-
S+
S-
SAV-GTWIN
1 ( )
call repeater
the FA-Gtwin power
the filter and line
LINE
PA Exterior door
release button
LINE~
SP
NC CONTACT =
SE+
DOOR CLOSED
SE-
NOTE: If it is not used,
join the 'SP' terminals with a cable.
2345
5
Tekna-S Gtwin
J2
MASTER
F. Line
MONITOR
SW2 ON (Z)
ON
1 2
INT 0
J2
MASTER
F. Line
MONITOR
SW2 ON (Z)
ON
1 2
INT 0
J2
MASTER
MONITOR F. Line
SW2 ON (Z)
ON
1 2
INT 0
J2
MASTER
F. Line
MONITOR
ON (Z)
SW2
ON
1 2
INT 0
QUICK GUIDE
FA-GTWIN
POWER SUPPLY
( )
2
LINE 1
08940- Cornellá de Llobregat
LINE 2
230
Golmar se reserva el derecho a cualquier modificación sin previo aviso.
0
Golmar se réserve le droit de toute modification sans préavis .
Golmar reserves the right to make any modifications without prior notice.
Code 50120265 TTEKNA S GTWIN EN QG REV.0319
golmar@golmar.es
Sistemas de comunicación S.A.
Monitor
GOLMAR S.A.
C/ Silici, 13
SPAIN
www.golmar.es